Aia Cad Standards 5h456s

ERDC/ITL TR-06-X

A/E/C CADD Standard Release 3.0

The A/E/C CADD Standard is compliant with Version 3.1 of the U.S. National CAD Standard The A/E/C CADD Standard contains supplemental materials and DoD specific requirements not addressed in the U.S. National CAD Standard.

for facilities, infrastructure, and environment

The CADD/GIS Technology Center

September 2006

Approved for public release; distribution is unlimited.

ERDC/ITL TR-06-X September 2006

A/E/C CADD Standard Release 3.0

Approved for public release; distribution is unlimited

Prepared for

U.S. Army Engineer Research and Development Center Vicksburg, MS 39180-6199

DISCLAIMER: The contents of this report are not to be used for advertising, publication, or promotional purposes. Citation of trade names does not constitute an official endorsement or approval of the use of such commercial products. All product names and trademarks cited are the property of their respective owners. The findings of this report are not to be construed as an official Department of the Army position unless so designated by other authorized documents.

Contents Preface ................................................................................................................. vii Introduction................................................................................................... vii United States National CAD Standard......................................................... viii 1—Introduction......................................................................................................1 Acronyms.........................................................................................................1 Scope................................................................................................................2 Purpose ............................................................................................................2 Background......................................................................................................2 International System of Units (SI) Considerations ..........................................3 Future Technologies ........................................................................................3 Target Systems.................................................................................................4 Design Applications and Other Applications ..................................................4 Coordination with Design Agent .....................................................................4 Additions/Revisions.........................................................................................5 2—Drawing File Organization...............................................................................6 Design Area .....................................................................................................6 Available drawing area..............................................................................6 File accuracy (units) ..................................................................................6 International Feet versus Survey Feet (V8)...............................................7 Origin (global origin) ................................................................................8 Model Files and Sheet Files.............................................................................8 Design Models and Sheet Models....................................................................9 Drawing Sheet Assembly.................................................................................9 Option 1 – Use of Design Model and Sheet Model.................................10 Option 2 – Use of Design Model Only....................................................10 Electronic Drawing File Naming Conventions..............................................11 Project Code ............................................................................................11 Model file naming convention ................................................................12 Sheet file naming convention ..................................................................17 Coordination Between Sheet File Name and Sheet Identifier .......................23 3—Graphic Concepts...........................................................................................24 Presentation Graphics ....................................................................................24 Line widths..............................................................................................24 Line types/styles......................................................................................25 Line color ................................................................................................26

iii

Screening.................................................................................................27 Text styles/fonts ......................................................................................27 Abbreviations ..........................................................................................30 Plotting ....................................................................................................30 Border Sheets.................................................................................................30 Sheet sizes ...............................................................................................30 Title block ...............................................................................................31 Drawing Scales ..............................................................................................34 Dimensioning.................................................................................................37 Dimensioning in Metric (SI)..........................................................................38 Millimeters ..............................................................................................38 Meters......................................................................................................38 Large units of measure ............................................................................39 Dual units ................................................................................................39 4—Level/Layer Assignments ..............................................................................40 Levels/Layers.................................................................................................40 Level/layer naming convention ...............................................................42 ISO format...............................................................................................43 Model Files ....................................................................................................43 Level/layer assignment tables .................................................................44 Border sheet model files..........................................................................46 Reference files (XREFs) .........................................................................46 Sheet Files......................................................................................................47 Level/layer assignment tables .................................................................47 Development of sheet files ......................................................................49 5—Standard Symbology ......................................................................................50 Introduction....................................................................................................50 Electronic Version of the Symbology/Elements............................................50 Deliverables.............................................................................................50 Line styles ...............................................................................................50 Tabulated Version of the Symbology/Elements ............................................51 References ............................................................................................................52 Appendix A: Model File Level/Layer Assignment Tables .................................A1 Appendix B: Sheet File Level/Layer Assignment Tables ................................... B1 Appendix C: Color Comparison.......................................................................... C1 Appendix D: A/E/C CADD Standard Symbology ..............................................D1

List of Figures

iv

Figure 2-1.

Sheet file composition ..................................................................9

Figure 2-2.

Sheet file composition using Design Model and Sheet Model .........................................................................................10

Figure 2-3.

Sheet file composition using only the Design Model.................11

Figure 2-4.

Model file naming convention ...................................................12

Figure 2-5.

Sheet file naming convention .....................................................18

Figure 2-6.

Typical border sheet title block with sheet identification block ...........................................................................................23

Figure 3-1.

Vertical title block ......................................................................32

Figure 3-2.

Designer identification block .....................................................33

Figure 3-3.

Issue block..................................................................................33

Figure 3-4.

Management block .....................................................................33

Figure 3-5.

Project identification block/sheet title block ..............................34

Figure 3-6.

Sheet identification block...........................................................34

Figure 3-7.

Dimension in millimeters. Always shown as a whole number........................................................................................38

Figure 3-8.

Dimension in meters. Always shown as a real number (with decimal) ............................................................................38

Figure 3-9.

Proper dimension presentations for metric measurements with four or fewer digits.............................................................39

Figure 3-10.

Proper dimension presentations for metric measurements with five or more digits ..............................................................39

Figure 4-1.

Typical levels/layers contained in a sheet file............................40

Figure 4-2.

Sheet- and model-specific information ......................................41

Figure 4-3.

Level/layer naming format .........................................................42

Figure 4-4.

ISO 13567-2 level/layer naming method ...................................43

Figure 4-5.

Model file level/layer assignment table......................................45

Figure 4-6.

Sheet file level/layer assignment table .......................................48

List of Tables

Table 2-1.

Discipline Designators ...............................................................13

Table 2-2.

Model File Types .......................................................................13

Table 2-3.

Discipline Designators with Level 2 Designators ......................19

Table 2-4.

Sheet Type Designators..............................................................22

Table 3-1.

Comparison of Line Widths .......................................................24

Table 3-2.

Standard Line Types/Styles........................................................26

Table 3-3.

Screen Color Comparison ..........................................................26

v

vi

Table 3-4.

Screened Colors..........................................................................27

Table 3-5.

Comparison of Font Types.........................................................29

Table 3-6.

ISO, ANSI, and Architectural Sheet Size Comparison ..............31

Table 3-7.

Typical Drawing Scales .............................................................35

Table 3-8.

Inch-pound Text Sizes and Line Type Scales ............................36

Table 3-9.

Metric Text Sizes and Line Type Scales ....................................37

Table 4-1.

Status (Phase) Codes ..................................................................46

Preface Introduction The A/E/C CADD Standard Manual has been developed by the CADD/GIS Technology Center (CGTC) for Facilities, Infrastructure, and Environment to eliminate redundant Computer-Aided Design and Drafting (CADD) standardization efforts within the Department of Defense (DoD) and the Federal Government. The manual is part of an initiative to develop a nonproprietary CADD standard that incorporates existing industry, national, and international standards and to develop data standards that address the entire life cycle of facilities within the DoD. The A/E/C CADD Standard Manual is part of a set of standards being developed by the CGTC. Additional manuals include the following: a. Contract Language Guidelines for Acquiring Geospatial Data (CADD, GIS, CAFM) System Deliverables from ArchitectEngineer (A-E) Consulting Firms, https://idoc-pub.cinepelis.org/cdn-cgi/l/email-protection" class="__cf_email__" data-cfemail="c48aa5aaa7bdea8eea86a8bda8a1b684acb5f4f6eab1b7a5a7a1eaa5b6a9bdeaa9ada8">[email protected]) Information on these standards, unless otherwise noted, can be obtained from the CGTC’s Web page at https://tsc.wes.army.mil. Mr. James T. Wilson is the Acting Chief of the CGTC, which is located in the Information Technology Laboratory (ITL), U.S. Army Engineer Research and Development Center (ERDC), Vicksburg, MS. The Director of ITL is Dr. Jeffery P. Holland, and the Assistant Director is Dr. Deborah F. Dent. At the time of publication of this report, the Director of ERDC was Dr. James R. Houston. Commander of ERDC was COL Richard B. Jenkins.

vii

United States National CAD Standard In 1995, the combined resources of the CGTC, the American Institute of Architects (AIA), the Construction Specifications Institute (CSI), the United States Coast Guard, the Sheet Metal and Air Conditioning Contractors National Association (SMACNA), the General Services istration (GSA), and the National Institute of Building Sciences’ (NIBS) Facility Information Council began an effort to develop a single CADD standard for the United States. Working together, these organizations agreed to develop an integrated set of documents that collectively would represent the U.S. National CAD Standard (NCS). A Memorandum of Understanding (MOU) was signed on August 8, 1997. In accordance with that MOU, Release 3.0 of the A/E/C CADD Standard follows, utilizes, or references the work developed by each of the signatories. The two main documents referenced within Release 3.0 of the A/E/C CADD Standard are: •

“Uniform Drawing System” The Construction Specifications Institute 99 Canal Center Plaza, Suite 300 Alexandria, VA 22314-1588 http://www.csinet.org

•

“AIA CAD Layer Guidelines” The American Institute of Architects 1735 New York Avenue, NW Washington, DC 20006-5292 http://www.aia.org

Each of these documents is available as part of the U.S. National CAD Standard. Additional information on the U.S. National CAD Standard can be obtained from NIBS Facility Information Council National Institute of Building Sciences 1090 Vermont Avenue NW, Suite 700 Washington, DC 20005-4905 http://www.nationalcadstandard.org

viii

1

Introduction

Acronyms First, a few useful acronyms:

Chapter 1

•

A-E – Architect-Engineer

•

A/E/C – Architectural, Engineering, and Construction

•

AIA – American Institute of Architects

•

ANSI – American National Standards Institute

•

ASTM – American Society for Testing and Materials

•

BIM – Building Information Modeling

•

CAD – Computer-Aided Design

•

CADD – Computer-Aided Design and Drafting

•

CGTC – The CADD/GIS Technology Center

•

CSI – Construction Specifications Institute

•

DoD – Department of Defense

•

FM – Facility Management

•

GIS – Geographic Information System

•

IAI – International Alliance for Interoperability

•

IFC – Industry Foundation Class

•

ISO – International Organization for Standardization

•

NCS – National CAD Standard

Introduction

1

•

NIBS – National Institute of Building Sciences

•

SI – International System of Units (Le Système International d’Unités)

•

UDS – Uniform Drawing System

Scope This manual provides guidance and procedures for preparing Computer-Aided Design and Drafting (CADD) products within the Department of Defense (DoD). Chapters 1-5 of this manual address topics such as presentation graphics, level/layer assignments, electronic file naming, and standard symbology. Appendices A-D contain tables on model and sheet file level/layer names, color comparisons, as well as Architectural, Engineering, and Construction (A/E/C) CADD symbology.

Purpose The purpose of this manual is to set a basic CADD standard to ensure consistent electronic deliverables (products) within the DoD. These consistent deliverables are part of a comprehensive installation life-cycle management strategy. This manual sets a CADD standard specifically for the A/E/C disciplines of facilities development and civil works projects. As this manual evolves, it will be integrated with other standards initiatives by the CADD/GIS Technology Center (CGTC) for Facilities, Infrastructure, and Environment such as Contract Language Guidelines and Building Information Modeling (BIM).

Background The immediate benefits of CADD standards are many: consistent CADD products for customers; uniform requirements for A-E deliverables; sharing of products and expertise; and collection, manipulation, and exchange of database information. Recognizing such potential benefits, each of the DoD agencies independently initiated efforts to establish CADD standards in the late 1980’s. The Air Force Logistics Command (1989) released the “Architectural and Engineering Services for CADD Implementation Within Air Force Logistics Command.” Headquarters, U.S. Army Corps of Engineers (1990), published Engineer Manual 1110-1-1807, “Standards Manual for U.S. Army Corps of Engineers Computer-Aided Design and Drafting (CADD) Systems.” In 1993, the 2

Chapter 1

Introduction

Naval Facilities Engineering Command distributed its “Policy and Procedures for Electronic Deliverables of Facilities Computer-Aided Design and Drafting (CADD) Systems.” To consolidate these efforts into a single standard, the CGTC was tasked to develop standards for the A/E/C disciplines. This manual presents the CGTC’s effort at standardizing CADD requirements for A/E/C design and construction documents.

International System of Units (SI) Considerations For this standard manual, the impact of the SI, more commonly referred to as the metric system, on such items as drawing scales, sheet sizes, and dimensioning is addressed. The SI was established by the General Conference of Weights and Measures of 1960, as interpreted or modified from time to time for the United States by the Secretary of Commerce under the authority of Public Law 94-168, the Metric Conversion Act of 1975, and the Metric Education Act of 1978. As of January 1, 1992, in accordance with Public Laws 94-168 and 100-418, the Omnibus Trade and Competitiveness Act of 1988, and Executive Order 12770, “Metric Usage in Federal Government Programs,” July 25, 1991, all new and revised construction standards and criteria must be developed using the SI.

Future Technologies There are several ongoing initiatives to create a universal language for collaborative work in the area of building and construction software. This work stems from the need to automate current building and construction tasks to become more efficient and cost effective. One of these initiatives is by the International Alliance for Interoperability (IAI), a nonprofit building industry alliance comprising architects, engineers, contractors, software vendors, government agencies, research laboratories, and universities. The goal of the IAI is to unite the A/E/C and Facility Management (FM) businesses by specifying Industry Foundation Classes (IFCs) as a universal language. The concept behind the IFCs is to create a series of standard intelligent software objects for the building industry that allow all process disciplines (i.e., architects, designers, engineers, builders, facilities managers) to exchange information. The IAI is developing IFCs that allow current software packages such as AutoCAD and MicroStation to share building and construction data. IFCs would improve the quality of the life cycle of a building from construction through maintenance and ultimately to demolition through reduced expense and delivery time, enhanced communications, and increased discipline proficiency.

Chapter 1

Introduction

3

Target Systems This manual does not target any specific CADD system or software. However, to ensure successful translations among CADD applications, certain system-specific characteristics were considered and the standard adjusted accordingly. During the preparation of the standard, several baseline decisions were made: •

The standard must be applicable to the latest release of commercially available CADD packages. AutoCAD and MicroStation were chosen based on their prevalence in the DoD.

•

The standard is based on CADD applications that utilize layer/level names and reference files.

•

The standard requires every final plotted drawing sheet to have its own separate electronic drawing file.

Since there have been considerable improvements and updates to CADD software, including changes to the file formats, it becomes more important to have a standard version of each appropriate CADD platform. Based on this, the following versions of the primary software products are considered the standard versions for use: •

MicroStation Version 2004 (ver. 8.5)

•

AutoCAD 2004

Design Applications and Other Applications Numerous design applications have been developed to run on top of basic CADD engines. These applications can be used by designers to generate graphics inside CADD files. Most notable are design software packages for civil/site and Building Information Modeling (BIM). Document management systems that contain attributes for individual files and have such features as title block integration are becoming standard tools for management of electronic files. Use of these systems to store searchable attribute information on files is encouraged.

Coordination with Design Agent With all the complexity and options currently available in the world of CADD, it becomes important to coordinate fundamental aspects of design work. The previously mentioned issues of basic platform, design

4

Chapter 1

Introduction

applications, and document management are only three of the issues that can affect the success of a project and the future usefulness of the final documents. As such, each project should have at its initiation discussions and agreements on such issues as this. Each software package being used should be approved and a determination made on how much of the ing electronic files should be provided to the customer as a part of the end product.

Additions/Revisions This standard is intended to be neither static nor all-inclusive and thus will be updated and enhanced as appropriate. Suggestions for improvements are strongly encouraged so that subsequent updates will reflect the input and needs of CADD s. Recommendations or suggested additions should be sent to: The CADD/GIS Technology Center U.S. Army Engineer Research and Development Center ATTN: CEERD-ID/Spangler 3909 Halls Ferry Road Vicksburg, MS 39180-6199 or by e-mail at: [email protected]

Chapter 1

Introduction

5

2

Drawing File Organization

Design Area Available drawing area

The two most extensively used CADD applications within the DoD, AutoCAD and MicroStation, both provide for a drawing area with infinite range in each positive and negative axis (x,y,z). File accuracy (units)

CADD systems allow the designer to work in “real-world” units. The most common units are feet:inches, feet:tenths of feet, and meters:millimeters. MicroStation’s approach to file accuracy allows the to set the working units (i.e., real-world units) as the following: •

Master Units = The largest unit that may be referred to when working in the design file (e.g., feet, meters)

•

Sub Units = Subdivisions of Master Units (e.g., inches, millimeters)

Note: For MicroStation V8, changing the Master Units in a drawing no longer changes the size of design file elements. For instance, if a design file was created in feet and a 1-ft line is drawn, changing the Master Units to inches results in the line measuring 12 in. For MicroStation V8, Positional Units have been eliminated (since these previously determined the size of the design cube and the ultimate accuracy of the file). Positional Units can still be set using the Settings – Design File – Working Units – Advanced button, but this is not recommended (unless the design file is going to be saved back to a MicroStation V7 file).

6

Chapter 2

Drawing File Organization

In AutoCAD, the basic drawing unit for any file is the distance between two fixed Cartesian coordinates. For example, the distance between coordinates (1,1,1) and (1,1,2) is one drawing unit. A drawing unit can correspond to any measurement (e.g., foot, inch, meter, mile, fathom). AutoCAD s may enter the Units display option to set the desired drawing units. The Units command of AutoCAD does not have a direct metric system setup. For metric designs, the recommended procedure is to choose the Decimal option in the Drawing Units dialogue box. This will allow each drawing unit to represent decimal meters, millimeters, etc., at the discretion of the . International Feet versus Survey Feet (V8)

Many sites have to deal with the initial question as to whether a particular project is designed using International Feet or Survey Feet. In some states, it is specified by statute that units of measure for grid coordinates have to be either International Feet or Survey Feet. The two units are defined as follows: •

International Feet: 1 foot = 0.3048000 m

•

U.S. Survey Feet: 1 foot = 0.3048006 m

Looking at this comparison, the difference between the two (0.0000006 m) may seem insignificant; however, ultimately this difference may cause coordinate values to be off by several feet, resulting in inaccurate design files. In MicroStation V8, the units.def file does contain a definition for Survey Feet (usually stored in Program Files\Bentley\Workspace\System\data), but it is disabled by default. To enable, scroll down the units.def file to the section English units (based on U.S. Survey Foot) and delete the # in front of #sf,ft, which will allow for the selection of Survey Feet from the Working Units box the next time MicroStation is started. Note: If a drawing has already been created using International Feet, changing the Master Units to Survey Feet will not automatically scale all elements in the drawing to Survey Feet. To address this problem, several Districts and A-E firms have developed macros to correctly scale existing elements, some of which also help bring V7 drawings into V8 while maintaining survey foot measurements.

Chapter 2

Drawing File Organization

7

Origin (global origin)

Positioned within every electronic drawing file is an origin (“global origin” in MicroStation and “origin” in AutoCAD). The origin of a drawing file is important because it serves as the point of reference from which all other elements are located. Origins are typically defined in a drawing file by the Cartesian coordinate system of x, y, and z. The benefit of standardizing the location of the origin of a drawing is most notable in the use of reference files (see section “Reference Files (XREFs)” in Chapter 4). A standardized origin is also helpful when translating files between CADD applications. The recommended global origin for 2D files in both AutoCAD and MicroStation drawings is x = 0 and y = 0. When 3D files are used, the z-origin should be set to allow for elevations below 0.

Model Files and Sheet Files Two distinct types of CADD files are addressed in this standard: model files and sheet files. A model file contains the physical components of a building (e.g., columns, walls, windows, ductwork, piping, etc.). Model files are drawn at full scale and typically represent plans, elevations, sections, etc. Model files can be generated either by placing graphics or from BIM model extractions. A sheet file is synonymous with a plotted CADD drawing file. A sheet file is a selected view or portion of referenced model file(s) within a border sheet. The addition of sheet-specific information (e.g., text, dimensions, and symbols) completes the construction of the document. In other words, a sheet file is a “ready-to-plot” CADD file. Figure 2-1 illustrates how different model files are referenced to a sheet file (notice that even the border sheet is a referenced model file). Again, a sheet file is the combination of referenced model files with sheetspecific text/symbols to create a final ready-to-plot CADD file. A useful rule of thumb was stated in the 2nd edition of the American Institute of Architects’ (AIA) CAD Layer Guidelines (AIA 2005): “Model files are always referenced by other files, while sheet files are never referenced by other files.”

8

Chapter 2

Drawing File Organization

Figure 2-1. Sheet file composition

Design Models and Sheet Models Inside each CADD file can exist Design Models (or Model Space for AutoCAD s) and Sheet Models (or Paper Space for AutoCAD s). Design Models are where model files are developed or possibly where model files are assembled together prior to creation of the Sheet Model (see the following section “Drawing Sheet Assembly”). Design Models contain graphic information in a model file format. For example, it may contain the entire Architectural Floor Plan model file for a building. It is this model file that is used as a reference for creating individual sheet files. By contrast, a Sheet Model shows the presentation of model file graphics as they would appear on an individual drawing sheet. This assembly area would contain referenced individual model files, one of which would be a border sheet.

Drawing Sheet Assembly Two main options for drawing sheet assembly may be used. Each involves assembling individual model files and a border sheet model file to create final plotted sheets. There are some differences that are explained in the following paragraphs. One similarity in both assembly processes is that nested referenced border sheet model files are not allowed. The method used should be defined at the start of a project, and all files should be built in the same manner.

Chapter 2

Drawing File Organization

9

Option 1 – Use of Design Model and Sheet Model

This option is the preferred method of drawing assembly (new to MicroStation s, but common to AutoCAD s, who are used to Paper Space). It consists of using a sheet file that contains a Design Model and a Sheet Model. The Design Model is used to assemble all the individual reference files necessary to display the graphics. This may include references to individual views of Design Models in other files, or even coincident references. The Design Model should also contain real-world graphics such as northing and easting coordinate values of points. The Sheet Model contains a reference to the project border sheet model file (at 1:1), plus a reference to the Design Model in the active sheet file, scaled to fit into the Sheet Model (Figure 2-2).

Figure 2-2. Sheet file composition using Design Model and Sheet Model

Option 2 – Use of Design Model Only

This option consists of using the Design Model only (the Sheet Model (or Paper Space) is not used). This Design Model would have all model files referenced to it, including the border sheet model file. Since all work would be done in the Design Model, a determination should be made at the start of any project using this option on whether to scale up the border sheet model file to fit around the 1:1 model files, or scale down the model files to fit inside the 1:1 border sheet model file (Figure 2-3). Whichever method is chosen, it should be consistent throughout the project.

10

Chapter 2

Drawing File Organization

Figure 2-3. Sheet file composition using only the Design Model

Electronic Drawing File Naming Conventions Naming conventions for electronic drawing files (both model files and sheet files) allow CADD s to determine the contents of a drawing without actually displaying the file. They also provide a convenient and clear structure for organizing drawing files within project directories. Project Code

The Model File naming convention and the Sheet File naming convention both allow for a 0- to 20-character Project Code at the beginning of the file name. Use of a Project Code is recommended and should be identified at the start of each project to ensure consistent file names within that project. Some examples of Project Codes are: •

The official agency project number

•

The project number defined by the agency system manager for their record system

The use of Project Codes in file names is highly recommended, because it prevents the same file name from existing in different directories. When this field is used, standard naming should consider use of a special character such as an underscore “_” for all model files so that folder sorting routines group like files together. When a project includes multiple sites or buildings, it is important to identify each file with the appropriate feature. This should be done as a part of the Project Code. For example, a model file for project P123, building 2, could possibly use a Project Code of “_P123-Bldg2”.

Chapter 2

Drawing File Organization

11

Model file naming convention

The model file naming convention (Figure 2-4) has one optional field, followed by three mandatory fields. While the first field is optional and may be omitted, the remaining fields must be used and in the correct sequence.

Figure 2-4. Model file naming convention

Following the optional Project Code field, the first two-character field represents the Discipline Designator. The allowable characters for the first character in the Discipline Designator are listed in Table 2-1. The second character of the Discipline Designator field is always a hyphen “-”. The next two-character field represents the Model File Type (Table 2-2). The final four-character field is Definable. Note: Several CADD Standards implementation packages use the file name conventions to determine the type of file being created, so certain character fields need to be located in the same position in every file name. If not all of the Definable characters are needed, placeholders must be used for these implementation tools to function properly. Example. The model file name for a project at the U.S. Army Engineer Research and Development Center (ERDC), Building 8000, 1st floor, Architectural Floor Plan could be: ERDC8000A-FPF1XX.dgn/dwg where ERDC8000 is the Project Code, A- is the Discipline Designator, FP is the Model File Type (Floor Plan), and F1 is a -definable set of characters for Floor 1. Since not all of the -definable characters were used, the characters XX were used as placeholders.

12

Chapter 2

Drawing File Organization

Table 2-1 Discipline Designators Discipline

Designator

General

G

Hazardous Materials

H

Survey/Mapping

V

Geotechnical

B

Civil

C

Landscape

L

Structural

S

Architectural

A

Interiors

I

Equipment

Q

Fire Protection

F

Plumbing

P

Process

D

Mechanical

M

Electrical

E

Telecommunications

T

Resource

R

Other Disciplines

X

Contractor/Shop Drawings

Z

Operations

O

Table 2-2 Model File Types Discipline

Code

Definition

General

BS

Border Sheet

Hazardous Materials

Survey/Mapping

CS

Cover Sheet

KP

Key Plan

DT

Detail

EL*

Elevation

LG

Legend

PP

Pollution Prevention Plan

QP*

Equipment Plan

SC

Section

XD*

Existing/Demolition Plan

AL

Existing Airfield Lighting Plan



Existing Communication System Plan

EU

Existing Electrical Utilities Plan

HP

Existing Hydrographic Survey and Mapping Plan

HT

Existing HTCW Utilities Plan

LG

Legend

PB

Property Boundary

PR

Existing Profile

SC

Existing Section

* = No Model File Table available in Appendix A

Chapter 2

Drawing File Organization

(Continued)

13

Table 2-2 (Continued) Discipline

Code

Definition

Survey/Mapping

SP

Survey and Mapping Plan

UP

Existing Utilities Plan

Geotechnical

Civil

Landscape

Structural

DT

Detail

JP

t Layout Plan

LB

Boring Log

LG

Legend

PV

Pavement Site Plan

SC

Section

SH*

Schedule

SI

Subsurface Investigation Plan

AF

Airfield Plan

BR

Beach Renourishment Plan

DT

Detail

EL

Elevation

ER

Eco-Restoration Plan

FC

Flood Control Plan

GP

Grading Plan

IP*

Installation Plan/Base Map

JP

t Layout Plan

KP*

Staking Plan

LG

Legend

NG

Navigation/Dredging Plan

PL*

Project Location Map

PR

Profile

SC

Section

SH*

Schedule

SP

Site Plan

TS

Transportation Site Plan

UP

Utilities Plan

XD*

Existing/Demolition Plan

DT

Detail

EL*

Elevation

IP

Irrigation Plan

LG

Legend

LP

Landscape Plan

SC*

Section

SH*

Schedule

XD*

Existing/Demolition Plan

3D

Isometric/3D

BP

Bridge Plan



Column Plan

CW

Misc. Small Civil Works Structures

DT

Detail

EL

Elevation

EP

Enlarged Plan

FC

Flood Control Structures

* = No Model File Table available in Appendix A

14

(Continued)

Chapter 2

Drawing File Organization

Table 2-2 (Continued) Discipline

Code

Definition

Structural

FP

Framing Plan

LD

Locks and Dams

Architectural

Interiors

Fire Protection

Plumbing

LG

Legend

NP

Foundation Plan

SC

Section

SH

Schedule

XD*

Existing/Demolition Plan

3D*

Isometric/3D

AC

Area Calculations/Occupancy Plan



Reflected Ceiling Plan

DT

Detail

EL

Elevation

EP*

Enlarged Plan

FP

Floor Plan

LG

Legend

QP

Equipment Plan

RP

Roof Plan

SC

Section

SH*

Schedule

XD*

Existing/Demolition Plan

3D*

Isometric/3D

DT

Detail

EL

Elevation

EP*

Enlarged Plan

FL

Floor Patterns

LG

Legend

QP*

Equipment Plan

RP

Furniture Plan

SC*

Section

SH*

Schedule

SP

Signage Placement Plan

WP

System Furniture Plan

XD*

Existing/Demolition Plan

3D*

Isometric/3D

DG*

Diagram

DT

Detail

FA

Fire Alarm/Detection Plan

FP

Fire Suppression Plan

LG

Legend

LP

Life Safety Plan

SH*

Schedule

XD*

Existing/Demolition Plan

3D*

Isometric/3D

DG

Diagram

DT

Detail

* = No Model File Table available in Appendix A

Chapter 2

Drawing File Organization

(Continued)

15

Table 2-2 (Concluded) Discipline

Code

Definition

Plumbing

EL*

Elevation

EP*

Enlarged Plan

Mechanical

Electrical

Telecommunications

LG

Legend

PP

Piping Plan

SH*

Schedule

XD*

Existing/Demolition Plan

3D*

Isometric/3D

DG

Diagram

DT

Detail

EL

Elevation

EP*

Enlarged Plan

HP

HVAC Plan

HS

Hydraulic Systems

HT

HTCW Utilities Plan

LG

Legend

MD

Machine Design Plan

MH

Material Handling Plan

QP*

Equipment Plan

SC

Section

SH*

Schedule

SP

Specialty Piping and Equipment Plan

XD*

Existing/Demolition Plan

AL

Airfield Lighting Plan

AP*

Auxiliary Power Plan



Exterior Communication Systems Plan

DG

Diagram

DT

Detail

EU

Electrical Utilities Plan

GP

Grounding System Plan

LG

Legend

LP

Lighting Plan

PP

Power Plan

SH*

Schedule

SS

Special Systems Plan

XD*

Existing/Demolition Plan

DG

Diagram

DT

Detail

LG

Legend

SH*

Schedule

TP

Telephone/Data Plan

XD*

Existing/Demolition Plan

* = No Model File Table available in Appendix A

16

Chapter 2

Drawing File Organization

Existing/Demolition model file naming. There are instances when a facility is being renovated and the as-built designs need to be revised to show demolition and new items. These revisions would not be made on existing as-built model files, but on copies to ensure the original as-builts are not modified. A model file type, Existing/Demolition (XD), has been added to the standard to allow s to make revisions to as-built files. This model file type is used to aid s in separating existing-to-remain items from items that will be demolished. Example. An architect has an existing as-built floor plan model file for Building 1000, 2nd floor. For the current project, walls will be demolished and new walls constructed on the 2nd floor. First, a copy would be made of the original as-built file (B1000A-FPF2XX.dgn/dwg) , and the copy would be named B1000RENA-XDF2XX.dgn/dwg (B1000REN is the Project Code, A- is the Discipline Designator, XD is the Model File Type (Existing/Demolition Plan), and F2XX are -definable characters (F2=Floor 2)). The architect would open this file and move all demolition items to demolition levels/layers (see Chapter 4, “Status (phase) levels/layers”). When the new items in the Floor Plan are drawn, the architect would open a new model file called something like B1000RENA-FPF2XX.dgn/dwg (B1000REN is the Project Code, A- is the Discipline Designator, FP is the Model File Type (Floor Plan), and F2XX are -definable characters (F2=Floor 2)). The file B1000RENA-XDF2XX.dgn/dwg would be referenced in with the demolition levels/layers turned off. The architect would then use the Floor Plan active levels/layers to construct the new items for that project. Sheet file naming convention

The sheet file naming convention (Figure 2-5) has one optional field for the Project Code, followed by four mandatory fields. Similar to the format for model file naming, all mandatory fields must be used and in the correct sequence. The first field is entirely optional and can be used for a 0- to 20character Project Code (see “Model file naming convention”). The next two characters are the Discipline Designator with Level 2 Designator (Table 2-3). The next character is the Sheet Type Designator (Table 2-4) followed by a two-character Sheet Sequence Number (01-99).

Chapter 2

Drawing File Organization

17

Figure 2-5. Sheet file naming convention

The remaining three characters are definable. Note: If the sheet sequence number goes above 99 sheets for a particular discipline, the first character in the Definable field could be used to expand the limit of sheets per discipline to 999. However, if more than 99 sheets are required for one discipline’s drawings, the might want to consider using the Level 2 Designator in the Discipline Designator to further subdivide the discipline (Table 2-3). Note: Occasionally, more than one Sheet Type (e.g., plan, elevation, detail) will be represented in one sheet file. If this is the case, the dominant Sheet Type determines the Sheet Type Designator. For example, the sheet file name for a project at ERDC, Building 8000, 1st floor, Quadrant B, Architectural Floor Plan, sheet sequence 02 could be: ERDC8000A-102F1B.dgn/dwg where ERDC8000 is the Project Code, A- is the Discipline Designator, 1 is the Sheet Type Designator (Plan), 02 is the Sheet Sequence Number, and F1B is a -definable set of characters for Floor 1, Quadrant B.

18

Chapter 2

Drawing File Organization

Table 2-3 Discipline Designators with Level 2 Designators Discipline

Designator Description

Content

General

G-

All General

All or any portion of subjects in the following Level 2 Designators

GI

General Informational

Drawing index, code summary, symbol legend, orientation maps

GC

General Contractual

Phasing, schedules, contractor staging areas, fencing, haul routes, erosion control, temporary and special requirements

GR

General Resource

Photographs, soil borings

H-

All Hazardous Materials

All or any portion of subjects in the following Level 2 Designators

HA

Asbestos

Asbestos abatement, identification, or containment

HC

Chemicals

Toxic chemicals handling, removal or storage

HL

Lead

Lead piping or paint removal

HP

PCB

PCB containment and removal

HR

Refrigerants

Ozone depleting refrigerants

V-

All Survey/Mapping

All or any portion of subjects in the following Level 2 Designators

VA

Aerial Survey

VF

Field Survey

VH*

Hydrographic Survey

VI

Digital Survey

VU

Combined Utilities

Geotechnical

B-

All Geotechnical

All or any portion of subjects in the following Level 2 Designators

Civil

C-

All Civil

All or any portion of subjects in the following Level 2 Designators

CB*

Civil Beach Renourishment

Beach Disposal and Renourishment

CD

Civil Demolition

Structure removal and site clearing

CE*

Civil Ecosystem Restoration

Environmental restoration

CF*

Civil Flood Control

Levees, spillways, pump stations

CG

Civil Grading

Excavation, grading, drainage, erosion control, retention ponds

CI

Civil Improvements

Pavers, flagstone, exterior tile, furnishings, retaining walls, and water features

CN*

Civil Navigation

Navigation, harbors, dredging

CO*

Civil Operation and Maintenance

Repair and O&M structures



Civil Paving

Roads, driveways, parking lots

CH*

Civil Shore Protection

Erosion protection structures on shoreline

CR*

Civil Recreation

Recreation facilities

CS

Civil Site

Plats, topographic, dimension control

CX*

Civil Security

Security-related work

CT

Civil Transportation

Waterways, wharves, docks, trams, railways, airfields, and people movers

CU

Civil Utilities

Water, sanitary sewer, storm sewer, power, communications, natural gas, and steam systems

Hazardous Materials

Survey/Mapping

* = Not in NCS 3.1

Chapter 2

Drawing File Organization

(Continued)

19

Table 2-3 (Continued) Discipline

Designator Description

Content

Landscape

L-

All Landscape

All or any portion of subjects in the following Level 2 Designators

LD

Landscape Demolition

Protection and removal of existing landscape

LI

Landscape Irrigation

LP

Landscape Planting

S-

All Structural

All or any portion of subjects in the following Level 2 Designators

SD

Structural Demolition

Protection and removal

Structural

Architectural

Interiors

Equipment

Fire Protection

SS

Structural Site

SB

Structural Substructure

SF

Structural Framing

Floors and roofs

A-

All Architectural

All or any portion of subjects in the following Level 2 Designators

AS

Architectural Site

Foundations, piers, slabs, and retaining walls

AD

Architectural Demolition

Protection and removal

AE

Architectural Elements

General architectural

AI

Architectural Interiors

AF

Architectural Finishes

AG

Architectural Graphics

I-

All Interiors

ID

Interior Demolition

IN

Interior Design

All or any portion of subjects in the following Level 2 Designators

IF

Interior Furnishings

IG

Interior Graphics

Murals and visuals

Q-

All Equipment

All or any portion of subjects in the following Level 2 Designators

QA

Athletic Equipment

Gymnasium, exercise, aquatic, and recreational

QB

Bank Equipment

Vaults, teller units, ATMs, drive-through

QC

Dry Cleaning Equipment

Washers, dryers, ironing, and dry cleaning

QD

Detention Equipment

Prisons and jails

QE

Educational Equipment

Chalkboards, library

QF

Food Service Equipment

Kitchen, bar, service, storage, and processing

QH

Hospital Equipment

Medical, exam, and treatment

QL

Laboratory Equipment

Science labs, planetariums, observatories

QM

Maintenance Equipment

Housekeeping, window washing, and vehicle servicing

QP

Parking Lot Equipment

Gates, ticket, and card access

QR

Retail Equipment

Display, vending, and cash

QS

Site Equipment

Bicycle racks, benches, playgrounds

QT

Theatrical Equipment

Stage, movie, rigging systems

QV

Video/Photographic Equipment

Television, darkroom, and studio

QY

Security Equipment

Access control and monitoring, surveillance

F-

All Fire Protection

All or any portion of subjects in the following Level 2 Designators

FA

Fire Detection and Alarm

FX

Fire Suppression

Fire extinguishing systems and equipment

* = Not in NCS 3.1

20

(Continued)

Chapter 2

Drawing File Organization

Table 2-3 (Continued) Discipline

Designator Description

Content

Plumbing

P-

All Plumbing

All or any portion of subjects in the following Level 2 Designators

PS

Plumbing Site

Extensions and connections to Civil Utilities

PD

Plumbing Demolition

Protection, termination, and removal

PP

Plumbing Piping

Piping, valves, and insulation

PQ

Plumbing Equipment

Pumps and tanks

PL

Plumbing

Domestic water, sanitary and storm drainage, fixtures

D-

All Process

All or any portion of subjects in the following Level 2 Designators

DS

Process Site

Extension and connection to civil utilities

DD

Process Demolition

Protection, termination, and removal

DL

Process Liquids

Liquid process systems

DG

Process Gases

Gaseous process systems

DP

Process Piping

Piping, valves, insulation, tanks, pumps, etc.

DQ

Process Equipment

Systems and equipment for thermal, electrical, materials handling, assembly and manufacturing, nuclear, power generation, chemical, refrigeration, and industrial processes

DE

Process Electrical

Electrical exclusively associated with a process and not the facility

DI

Process Instrumentation

Instrumentation, measurement, recorders, devices and controllers (electrical and mechanical)

M-

All Mechanical

All or any portion of subjects in the following Level 2 Designators

MS

Mechanical Site

Utility tunnels and piping between facilities

MD

Mechanical Demolition

Protection, termination, and removal

Process

Mechanical

Electrical

MH

Mechanical HVAC

Ductwork, air devices, and equipment

MP

Mechanical Piping

Chilled and heating water, steam

MI

Mechanical Instrumentation

Instrumentation and controls

MY*

Mechanical Hydraulic Systems

Pump stations, spillways, slide gates

E-

All Electrical

All or any portion of subjects in the following Level 2 Designators

EA*

Electrical Airfield Lighting and Navaids

Visual air navigation systems

ES

Electrical Site

Exterior electrical systems (power, lighting, auxiliary)

EC*

Electrical Cathodic Protection

Cathodic protection systems

EG*

Electrical Grounding

Grounding, lightning protection devices

ED

Electrical Demolition

Protection, termination, and removal

EP

Electrical Interior Power

Interior power

EL

Electrical Interior Lighting

Interior lighting

EI

Electrical Instrumentation

Controls, relays, instrumentation, and measurement devices

EY

Electrical Interior Auxiliary Alarms, nurse call, security, CCTV, PA, music, clock, and Systems program

* = Not in NCS 3.1

Chapter 2

Drawing File Organization

(Continued)

21

Table 2-3 (Concluded) Discipline

Designator Description

Content

Telecommunications

T-

All Telecommunications

All or any portion of subjects in the following Level 2 Designators

TD*

Telecommunications Demolition

Protection, termination, and removal

TA

Audio Visual

Cable, music, and CCTV systems

TC

Clock and Program

Time generators and bell program systems

TI

Intercom

Intercom and public address systems

TM

Monitoring

Monitoring and alarm systems

Resource

TN

Data Networks

Network cabling and equipment

TS*

SCADA

Supervisory Control and Data Acquisition (SCADA) systems and equipment

TT

Telephone

Telephone systems, wiring, and equipment

TY

Security

Access control and alarm systems

R-

All Resource

All or any portion of subjects in the following Level 2 Designators

RC

Resource Civil

Surveyor's information and existing civil drawings

RS

Resource Structural

Existing facility structural drawings

RA

Resource Architectural

Existing facility architectural drawings

RM

Resource Mechanical

Existing facility mechanical drawings

RE

Resource Electrical

Existing facility electrical drawings

Other Disciplines

X

Contractor/Shop Drawings

Z

Operations

O

* = Not in NCS 3.1

Table 2-4 Sheet Type Designators

22

Sheet Type

Designator

General (symbols legend, notes, etc.) Plans (horizontal views) Elevations (vertical views) Sections (sectional views) Large-Scale Views (plans, elevations, or sections that are not details) Details Schedules and Diagrams Defined Defined 3D Representations (isometrics, perspectives, photographs)

0 1 2 3 4 5 6 7 8 9

Chapter 2

Drawing File Organization

Coordination Between Sheet File Name and Sheet Identifier In asg a sheet identifier (for use in the sheet identification block, reference bubbles, etc.), the should coordinate with the name assigned to the electronic sheet file. The sheet identifier should consist of the discipline designator, sheet type designator, and the sheet sequence number (Figure 2-6).

Figure 2-6. Typical border sheet title block with sheet identification block

As far as the sequence of the discipline designators in a drawing set, the National CAD Standard mandates that the disciplines follow the order as shown in Table 2-1.

Chapter 2

Drawing File Organization

23

3

Graphic Concepts

Presentation Graphics The first step in establishing an effective CADD standard is the development of a uniform approach to presentation graphics. Presentation graphics typically consist of drawing elements such as lines, arcs, shapes, text, and their attributes (line color, line width, and line style). This chapter presents brief overviews of the characteristics of presentation graphics and the philosophy used to standardize them. Line widths

Although “monotone” line work is not contractually improper, varied line widths substantially improve readability. Most commercial CADD systems provide an extensive variety of line widths. However, for the majority of A/E/C drawings, the eight line widths defined in Table 3-1 are considered sufficient and should not be expanded unless an appreciable improvement in drawing clarity or contrast can be realized. Table 3-1 shows information about the various allowed line widths. Table 3-1 Comparison of Line Widths Line Thickness

mm

Fine

0.18 0.007 wt = 0

Patterning

Thin

0.25 0.010 wt = 1

Dimension lines, dimension leader/witness lines, note leader lines, long break lines, schedule grid lines, and objects seen at a distance

in.

MicroStation Line Weight

Typical Use

Medium

0.35 0.014 wt = 2

Minor object lines

Wide

0.50 0.020 wt = 3

Major object lines, cut lines, section cutting plane lines, and titles

Extra Wide

0.70 0.028 wt = 5

Minor title underlining, match lines, schedule outlines, large titles, and object lines requiring special emphasis

XX Wide

1.00 0.040 wt = 7

Major title underlining and separating portions of drawings

XXX Wide

1.40 0.055 wt = 10

Border sheet outlines and cover sheet line work

XXXX Wide

2.00 0.079 wt = 15

Border sheet outlines and cover sheet line work

24

Chapter 3

Graphic Concepts

•

Fine (0.18 mm). Fine lines should be used sparingly, mostly for hatching/patterning (this line thickness typically does not reproduce well in blue-line format and/or in photocopies).

•

Thin (0.25 mm). Thin lines should be used for depicting dimension lines, dimension leader/witness lines, note leader lines, line terminators (arrowheads, dots, slashes), phantom lines, hidden lines, center lines, long break lines, schedule grid lines, and object lines seen at a distance.

•

Medium (0.35 mm). Medium lines should be used for depicting most object lines, text (dimensions, notes/callouts, and schedule), and schedule grid accent lines.

•

Wide (0.50 mm). Wide lines should be used for major object lines, cut lines, section cutting plane lines, and titles.

•

Extra wide (0.70 mm). Extra-wide lines should be used for minor title underlining, schedule outlines, large titles, and object lines requiring special emphasis. For very large scale details drawn at 3 in. = 1 ft-0 in. or larger, the extra-wide width should be used for the object lines. Extra-wide widths are also appropriate for use as an elevation grade line, building footprint, or top of grade lines on section/foundation details.

•

XX Wide (1.00 mm). This line weight should be used for major title underlining and separating portions of drawings.

•

XXX Wide (1.40 mm). This line weight should be used for border sheet outlines and cover sheet line work.

•

XXXX Wide (2.00 mm). This line weight should be used for border sheet outlines and cover sheet line work.

Line types/styles

The predominant line types/styles used in this standard are listed in Table 3-2. The CGTC has created line style files for MicroStation and AutoCAD (called tsaec.rsc and tsaec.lin, respectively), which include the line styles in Table 3-2, as well as additional discipline custom line styles (see Appendix D). These files are available on the CGTC’s Internet site at https://tsc.wes.army.mil.

Chapter 3

Graphic Concepts

25

Table 3-2 Standard Line Types/Styles ID Description

MicroStation Designator

AutoCAD Designator

0

Continuous

0

Continuous

1

Dotted

1

Dot

2

Dashed

2

Hidden

3

Dashed spaced

3

Dashed

4

Dashed dotted

4

Dashdot

6

Dashed double-dotted

6

Divide2

7

Chain

7

Center

Example

Line color

The primary reason to use color in CADD drawings is to improve the clarity of the drawing on a computer monitor. The variety of colors available in a CADD application depends on the capabilities of the computer monitor and its video card. Today, most systems are capable of displaying up to 16.8 million colors. For consistency, this manual recommends that all A/E/C drawings be created using the basic colors presented in Table 3-3 whenever possible. Note: The recommended colors are best viewed on a monitor with a black background. Appendix C contains a 256-color map for the AutoCAD and MicroStation color palettes. The table maps AutoCAD’s default color palette to MicroStation’s default color palette. The color table is provided for those s who require more colors than the eight shown in Table 3-3. Table 3-3 Screen Color Comparison Color Number

Ratios of RGB

Color

AutoCAD

MicroStation

Red

Green

Blue

Blue

5

1

0

0

255

Gray

8

9

128

128

128

Green

3

2

0

255

0

Red

1

3

255

0

0

Yellow

2

4

255

255

0

Magenta

6

5

255

0

255

Cyan

4

7

0

255

255

White

7

0

255

255

255

Note: Color numbers for AutoCAD and MicroStation were taken from default color tables.

26

Chapter 3

Graphic Concepts

Screening

Screened images are created through a process in which the density and pattern of black and white dots are varied to simulate different shades of gray. Varying the intensity of gray scales allows s to distinguish different aspects of a drawing when it is plotted. For example, an area on a site designated for demolition can be assigned a color that has been assigned a screening percentage. When plotted, the area will be shown at a lighter shade compared with other elements in the drawing. This will allow the contractor to immediately identify the demolition area on the drawing. Table 3-4 lists colors recommended to be used for screening along with a recommended screening percentage. Optionally, when variations in screening are not important, a single screening can be applied to all screened graphics. Table 3-4 Screened Colors AutoCAD

MicroStation Screen percent

Gray Scale Ratios (RGB)

Color No.

Screen percent

Color No.

Red

Green

Blue

250

60

8

60

102

102

102

251

50

200

50

128

128

128

252

40

168

40

153

153

153

253

30

120

30

179

179

179

254

20

56

20

204

204

204

Text styles/fonts

Each of the two major CADD platforms contains sets of fonts that have been designed for use in CADD drawing presentation. MicroStation has various fonts stored in font resource files, with each resource file capable of containing multiple fonts. AutoCAD has individual fonts as shape files. In addition, each platform has the ability to True Type fonts that are installed on the individual computer. Although True Type fonts present a very useful alternative for fonts, there are drawbacks with their use. The most notable drawback is the longer time for rendering the drawing on the screen, and the longer time required for actual plotting. Each application also has the ability to create additional fonts for its use. Since projects designed in CADD are planned for use many years into the future and files will be used by many different individuals, use of any nonstandard font is not recommended. This includes fonts for symbology, logos, business titles, etc.

Chapter 3

Graphic Concepts

27

There is not a direct relationship between MicroStation resource files and AutoCAD shape files. Therefore it is important that font use be reviewed at the start of a project and decisions made on fonts that are then used consistently throughout the project by all disciplines. If a project is to be exchanged between CADD platforms either because individual offices require different CADD applications, or because the end requires a specific software format, a general guideline would be to use True Type fonts. This would allow direct translations between the applications. If a project is to be designed in a single CADD application and there is no likelihood that there will be a need to translate it to a different CADD platform, then the native CADD application fonts should be used. Contrasting text styles (or fonts) are used within a drawing to delineate types of information. In most A/E/C drawings, the fonts shown in Table 3-5 should be sufficient.

28

•

Monotext font. This font creates text characters that are evenly spaced. Monotext font should be used where text fields need to be aligned such as in schedules or, in some cases, title blocks.

•

Proportional font. This font creates text where the characters are proportionally spaced. It is appropriate for general notes, labels, or title blocks.

•

Slanted font. A slanted font is used where text needs to be easily distinguished from other text.

•

Filled font. Filled fonts are used primarily for titles and on cover sheets.

•

Outline font. When a pen plotter is used for final output, the outline font is used as a substitute for filled fonts for major titles such as cover sheet information to save plotting time.

•

Symbology font. This font should be used in cases where Greek symbols are representations for technical information.

Chapter 3

Graphic Concepts

Chapter 3

Graphic Concepts

29

Abbreviations

Abbreviations for words or phrases frequently used in plans, sections, elevations, or details should follow the abbreviations as established in the NCS (UDS Module 5 – and Abbreviations). When possible, the use of abbreviations should be kept to a minimum. Other abbreviations, particularly discipline-unique abbreviations, may be used but must not conflict with those established in the NCS. The NCS Standard is available for purchase from the National Institute of Building Sciences at http://www.nibs.org/ncsorderform.html. Plotting

Printers and plotters are controlled by files called pen tables or feature tables. These files (tables) convert thicknesses and/or color in an electronic file to line thicknesses on a paper drawing. This manual standardizes presentation graphics as they relate to electronic drawing files (screen display) and not the final printed or plotted paper drawing. By employing pen tables, each agency can ensure that consistent drawings are produced from an electronic file regardless of the type of printer or plotter used. It is the responsibility of each field activity to develop pen tables based on the printer/plotter used at that activity.

Border Sheets Sheet sizes

Typical A/E/C projects (contract documents) will be prepared on American National Standards Institute (ANSI) D sheets (ANSI E may be used for large maps (i.e., installation master plans and drawings for civil works projects)). For international projects, International Organization for Standardization (ISO) A1 sheets are to be used (ISO A0 may be used for large maps). Other industry standard sizes may be used depending on specific customer requirements. Table 3-6 lists the standard sizes of all sheets.

30

Chapter 3

Graphic Concepts

Table 3-6 ISO, ANSI, and Architectural Sheet Size Comparison Width

Length

ANSI Equivalent

Architectural Equivalent

ISO Designation

mm

in.

mm

in.

Letter

in.

Letter

in.

NA

NA

NA

NA

NA

F

28.0 x 40.0

F

30.0 x 42.0

A0

841

33.11

1189

46.81

E

34.0 x 44.0

E

36.0 x 48.0

A1

594

23.39

841

33.11

D

22.0 x 34.0

D

24.0 x 36.0

A2

420

16.54

594

23.39

C

17.0 x 22.0

C

18.0 x 24.0

A3

297

11.69

420

16.54

B

11.0 x 17.0

B

12.0 x 18.0

A4

210

8.27

297

11.69

A

8.5 x 11.0

A

9.0 x 12.0

To develop the graphics for the sheet border, the following guidelines are to be used: • Top and bottom margin: 3/4 inch (20 mm) • Left margin: 1-1/2 inch (40 mm) • Right margin: 3/4 inch (20 mm) Note: s plotting A1 size drawings on ANSI D-size paper should reduce the width of the A1 border from 594 mm (23.39 in.) to 559 mm (22.0 in.). The length can remain the same. This revised border will fit on an ANSI D-size sheet (22 by 34 in.) and can be reproduced on standard office photocopiers. Title block

The CGTC recommends the use of a vertical title block placed in the right-hand margin of the border sheet as shown in Figure 3-1. Use of the vertical title block provides the most usable drawing space on a sheet. The vertical title block also ensures that the most prevalent and pertinent information remains at the bottom right of the sheet. In compliance with the Uniform Drawing System (Construction Specifications Institute (CSI) 2004), title block data will include the following: •

Designer identification block

•

Issue block

•

Management block

•

Project identification block/sheet title block

•

Sheet identification block

Note: Local standards may modify the content of the title block but should not alter its size or configuration if possible. See the Uniform Drawing System for additional recommendations.

Chapter 3

Graphic Concepts

31

Figure 3-1. Vertical title block

Designer identification block. The designer identification block (Figure 3-2) contains the logo or name of the agency that designed the sheet. This space could also be expanded by reducing the size of the issue block to accommodate professional seals when required. Issue block. The issue block (Figure 3-3) contains a history of revisions, addenda, and/or clarifications to the sheet. The first entry should be placed on the lower left-hand line of the issue block and subsequent entries should be made above it. Management block. The management block (Figure 3-4) contains information about the designer, reviewer, and submitter. This block can also be used to maintain filing information about the drawing, such as the file name, plot scale, and drawing code (this information is sometimes plotted outside the drawing sheet cut line). If an A-E has developed the drawings, there is room for information about the firm in the lower left portion of the block. The management block can also contain authorization block information. This is typically where the principals of the design agent would sign drawings, either for a whole project or by individual disciplines. Also, sometimes a disclaimer is included stating whether the project was designed by a Government agency or through a contract with a Government agency.

32

Chapter 3

Graphic Concepts

Figure 3-2. Designer identification block

Figure 3-3. Issue block

Figure 3-4. Management block

Project identification block/sheet title block. The project identification block/sheet title block (Figure 3-5) contains two sets of information. First, the project name is identified, possibly with the location or phase of the project identified. If small enough, a project logo can be presented in this block. The second set of information contains a description of the

Chapter 3

Graphic Concepts

33

content of the sheet (e.g., Architectural Floor Plan). If more than one type of information is presented on the sheet (i.e., plans, schedules, details), the most important information is identified.

Figure 3-5. Project identification block/sheet title block

Sheet identification block. The sheet identification block (Figure 3-6) contains the sheet identifier. This sheet identifier is composed of the discipline designator, the sheet type designator, and the sheet sequence number described in the section, “Electronic Drawing File Naming Conventions” (Chapter 2). The “number of sheets” listing is optional and can contain either the total number of sheets for the entire project drawing set or the number of sheets for that particular discipline designator.

Figure 3-6. Sheet identification block

Drawing Scales Typical drawing scales for both SI and inch-pound measurements are indicated in Table 3-7. The National CAD Standard (National Institute of Building Sciences (NIBS) 2005) recommends that the minimum text height for plotted CADD files is 3/32” (2.4 mm). However, to maintain legibility in half-size 34

Chapter 3

Graphic Concepts

drawings, most sites go no lower than 1/8” (3 mm) in text height. Table 3-8 lists recommended text sizes for common inch-pound scales, as well as line type scale factors for those scales. Table 3-9 lists recommended text sizes for common metric scales. (Note: The scales shown are not all-inclusive. Scales used should be limited to those commonly found on hand-held architectural, mechanical, and engineering scales.) Table 3-7 Typical Drawing Scales Drawing Type

Metric

Inch-Pound

Site Plans

1:200

1" = 20'

1:400

1" = 30'

1:500

1" = 40'

1:600

1" = 50'

Floor Plan

1" = 60'

1:1000

1" = 100'

1:2000

1" = 200'

1:5000

1" = 400'

1:6000

1" = 500'

1:10000

1" = 1000'

1:20000

1" = 2000'

1:50

1/4" = 1' - 0"

1:100

1/8" = 1' - 0"

1:200

1/16" = 1' - 0"

Roof Plan

1:200

1/16" = 1' - 0"

Exterior elevations

1:100

1/8" = 1' - 0"

1:200

1/16" = 1' - 0"

Interior Elevations Cross sections

Chapter 3

1:700

1:50

1/4" = 1' - 0"

1:100

1/8" = 1' - 0"

1:50

1/4" = 1' - 0"

1:100

1/8" = 1' - 0"

1:200

1/16" = 1' - 0"

Wall sections

1:20

1/2" or 3/4" = 1' - 0"

Stair details

1:10

1" or 1-1/2" = 1' - 0"

Details

1:5

3" = 1' - 0"

1:10

1" or 1-1/2" = 1' - 0"

Graphic Concepts

35

Table 3-8 Inch-pound Text Sizes and Line Type Scales

36

Scale

Text Size

Line Type Scale

12" = 1' - 0" or Full Size

0.125"

1

6” = 1’-0”

0.25”

2

3" = 1' - 0"

0.50"

4

1-1/2" = 1' - 0"

1"

8

1" = 1' - 0"

1.5"

12

3/4" = 1' - 0"

2"

16

1/2" = 1' - 0"

3"

24

3/8" = 1' - 0"

4"

32

1/4" = 1' - 0"

6"

48

3/16" = 1' - 0"

8"

64

1/8" = 1' - 0"

12"

96

3/32" = 1' - 0"

16"

128

1/16" = 1' - 0"

24"

192

1/32" = 1' - 0"

48"

384

1" = 5'

7.5"

60

1" = 10'

1.25’

120

1" = 20'

2.5’

240

1" = 30'

3.75’

360

1" = 40'

5’

480

1" = 50'

6.25’

600

1" = 60'

7.5’

720

1" = 100'

12.5’

1200

1" = 200'

25’

2400

1" = 400'

50’

4800

1" = 500'

62.5’

6000

1" = 1000'

125’

12000

1" = 2000'

250’

24000

Chapter 3

Graphic Concepts

Table 3-9 Metric Text Sizes and Line Type Scales Scale

Text Size

Line Type Scale

1:1 or Full Size

3 mm

1

1:2.5

7.5 mm

2.5

1:5

15 mm

5

1:10

30 mm

10

1:20

60 mm

20

1:30

90 mm

30

1:40

120 mm

40

1:50

150 mm

50

1:60

180 mm

60

1:100

300 mm

100

1:200

600 mm

200

1:400

1.2 m

400

1:500

1.5 m

500

1:600

1.8 m

600

1:700

2.1 m

700

1:1000

3.0 m

1000

1:2000

6.0 m

2000

1:5000

15 m

5000

1:6000

18 m

6000

1:10000

30 m

10000

1:20000

60 m

20000

Dimensioning As far as the appearance of dimensions, the NCS is very specific. Dimension text heights should match the size of the text in the rest of the drawing (i.e., notes and callouts) and the location of the dimension text should be at the midpoint and top of the dimension line (where possible). Dimension lines should be offset a minimum of 9/16” (14.5 mm) and extension lines should be offset a minimum of 1/16” (1.5 mm) from the element being dimensioned. Slashes are recommended by the NCS for dimension terminators; however, filled arrowheads are allowed in the A/E/C CADD Standard, as long as the arrowhead width is 1.5 * TH (TH = dimension text height) and the height is 0.5 * TH. This achieves the NCS requirement of 3:1 filled arrowheads. Dimension terminator selection should be consistent across the entire set of drawings.

Chapter 3

Graphic Concepts

37

Dimensioning in Metric (SI) Methodologies for dimensioning metric (SI) drawings are based upon the recommendations of the Construction Metrication Council of NIBS, Washington, DC. These recommendations comply with the American Society for Testing and Materials (ASTM) E 621-94 (ASTM 1999). Millimeters

The preferred unit of measure for most A/E/C work is millimeters. Unit notations are unnecessary and should not be used. The dimension is provided as a whole number as shown in Figure 3-7. Also, a note should be added to the drawing stating, “All dimensions and/or dimensions shown in callouts/notes are in millimeters unless otherwise noted.” When meter measurements are included on the same sheet, the meter dimension is provided as a real number taken to three places past the decimal point (Figure 3-8). Again, unit notations are unnecessary.

Figure 3-7. Dimension in millimeters. Always shown as a whole number

Figure 3-8. Dimension in meters. Always shown as a real number (with decimal)

Note: In circumstances where very small dimensions are used (e.g., machine details), it is permissible to use real numbers for millimeter dimensions. A note should be placed on the detail regarding this fact. Meters

For site plans or other drawings drawn to scales over 1:200, the unit of measure is typically meters. Where greater accuracy is required, show dimensions to three decimal places (Figure 3-8). A note should be added to the drawing stating, “All dimensions and/or dimensions shown in callouts/notes are in meters unless otherwise noted.” 38

Chapter 3

Graphic Concepts

Large units of measure

Commas shall not be used when providing large units of measure; instead, a space replaces the traditional comma in numbers containing five or more digits (e.g., the number 45,000 is displayed as 45 000). In numbers containing four digits, no space is necessary (e.g., 5000). These methods are shown in Figures 3-9 and 3-10. Note: The automatic dimensioning features of AutoCAD do not allow s to replace commas with spaces in dimension text. The dimension text will presently have to be edited to provide the spacing required by ASTM E 621-94 (ASTM 1999).

Figure 3-9. Proper dimension presentations for metric measurements with four or fewer digits

Figure 3-10. Proper dimension presentations for metric measurements with five or more digits

Dual units

To avoid confusion, dual units (both inch-pound and metric) should not be used. As stated in Construction Metrication Council (1998), the use of dual units “increases dimensioning time, doubles the chance for errors, makes drawings more confusing, and only postpones the (metric) learning process.” Exceptions to this include certain “standard building designs” where dual dimensions ensure that the design can be used in either SI or inchpound projects and in situations where products/components used in an SI project are available only as inch-pound products.

Chapter 3

Graphic Concepts

39

4

Level/Layer Assignments

Levels/Layers CADD levels or layers are analogous to overlays in manual drafting systems and serve to separate graphic elements (lines, shapes, and text) according to the design discipline they represent (Figure 4-1).

Figure 4-1. Typical levels/layers contained in a sheet file

The types of information represented by individual levels/layers can be grouped into two primary types: model-file-specific information and sheet-file-specific information (Figure 4-2). Sheet-file-specific

40

Chapter 4

Level/Layer Assignments

information can then be broken down into two secondary types: designmodel-specific and sheet-model-specific.

Figure 4-2. Sheet- and model-specific information

•

Chapter 4

Model-file-specific information represents the physical form of a site, a building, or objects composing a building. This information is often shared between CADD files (both model file and sheet file) through the use of reference files. Examples include walls, doors, light fixtures, and room numbers. Model-file-specific information may be either literal (e.g., walls) or symbolic (e.g., electrical outlets).

Level/Layer Assignments

41

•

Sheet-file-specific information may include notes, annotative symbols, and titles. This type of information is usually not shared between CADD files or drawings. Design models inside a sheet file contain graphic information that would relate to real-world information (e.g., point coordinates), or information that would be sectioned off into multiple sheets (e.g., a floor plan that may take three sheets to present because of its size). Sheet-model-specific information would include items specific for the presentation of that sheet. This is one reason that sheet models should never be used as a reference file to other files.

A third type of information exists for BIM. The files created in BIM are different from model files and sheet files because they are not directly referenced as graphics in the generation of drawings. Information from BIM is extracted and used to create the traditional models used in CADD generation of drawings. To use and manipulate model-file- and sheet-file-specific information effectively, every level/layer must be defined (standardized) by its name and its use. Level/layer naming convention

The reuse, not duplication, of graphic information reduces drawing time and improves project coordination. The level/layer is the basic tool used in CADD for managing graphic information (Figure 4-3). The levels/layers defined within this standard are based on the recommendations set forth in “AIA CAD Layer Guidelines” (AIA 2005).

Figure 4-3. Level/layer naming format

A basic level/layer name consists of a two-character Discipline Designator (e.g., “A-“ for Architectural, “M-“ for Mechanical), a four-character Major Group (e.g., “DOOR” for Doors, “LITE” for Lighting Fixtures), and a four-character Minor Group (e.g., A-WALL-CNTR for wall center lines, M-HVAC-CDFF for HVAC ceiling diffs). For further differentiation, another four-character Minor Group may be used (e.g.,

42

Chapter 4

Level/Layer Assignments

A-WALL-FULL-EXTR for exterior full-height walls versus A-WALLFULL-INTR for interior full-height walls). An optional item to indicate Status or Phase can also be added to every level/layer name (See “Status (Phase) levels/layers” later in this chapter). ISO format

ISO 13567-2 (1SO 1998) presents an international method for level/layer naming (Figure 4-4). This method consists of 10 mandatory alphanumeric characters, followed by 10 optional alphanumeric characters. The first two-character field, Agent Responsible, correlates to the AIA’s Discipline Designator. The following six-character field, Element, can map to a shortened version of the AIA’s Major and Minor Groups (e.g., DOOR-FULL becomes DOORFU, DOOR-PRHT becomes DOORPR). The final two-character field in the mandatory level/layer name, Presentation, designates whether the level/layer information is Model information (i.e., model-specific information) or Page/Paper information (i.e., sheet-specific information). Appendix A gives a corresponding ISO Format level/layer name for each AIA Format level/layer name.

Figure 4-4. ISO 13567-2 level/layer naming method

Model Files As mentioned in Chapter 2, model files represent full-size drawings of building elements, systems, or information (e.g., the mechanical HVAC system, the architectural floor plan, details, or sections), and sheet files represent final plotted sheets. Model files are used as components in creating plotted sheet files. The information contained within a model file for a discipline may be referenced by other disciplines to create the particular model files or sheet files for that discipline.

Chapter 4

Level/Layer Assignments

43

A model file can be considered a work in progress. For instance, a mechanical engineer may reference the architect’s floor plan model file to begin development of the HVAC ductwork layout model file. Meanwhile, the architect can continue developing the floor plan to meet new requirements. Any changes to the floor plan would be immediately accessible to the mechanical engineer. The viewing of real-time updates eliminates a great deal of frustration for other disciplines because it allows for on-the-spot rather than after-the-fact modifications. Level/layer assignment tables

The level/layer assignment tables in Appendix A present the following (Figure 4-5 presents an excerpt): •

The levels/layers assigned to each model file.

•

An AIA and corresponding ISO format level/layer name for each level/layer.

•

A detailed description for each level/layer.

•

The recommended presentation graphics associated with each level/layer. This includes the line style, line width, and color. (Note: The recommended presentation graphics may be changed to aid in drawing clarity (e.g., to show hidden objects). However, the recommended presentation graphics should be adhered to as much as possible to maintain drawing consistency.)

•

The various model files that levels/layers can be created in.

Annotation levels/layers. The function of annotation levels/layers is to contain model-specific information that might not be required by other disciplines. These levels/layers are as follows with ** representing a Discipline Designator (e.g., A-, C-): **ANNO-DIMS Witness/extension lines, dimension terminators, and dimension text. **ANNO-KEYN Reference keynotes with associated leaders. **ANNO-NOTE General notes and remarks. **ANNO-NPLT Non-plotting graphic information.

44

Chapter 4

Level/Layer Assignments

**ANNO-PATT Patterning, poche, shading, and hatching. **ANNO-SYMB Miscellaneous symbols. **ANNO-TEXT Miscellaneous text and callouts with associated leaders. **ANNO-RDME Read-me information. **ANNO-REFR An AutoCAD -specific layer for use in attachment of external references (i.e., reference files).

Figure 4-5. Model file level/layer assignment table

Status (Phase) levels/layers. In some cases, levels/layers may be modified to show the status of a particular item in the drawing (e.g., to be demolished, to be moved, future work, etc.). In these cases, levels/layers may have a Status Field appended to them as shown in Figure 4-3. See Table 4-1 for the Status (Phase) codes.

Chapter 4

Level/Layer Assignments

45

Table 4-1 Status (Phase) Codes Code

Description

N

New work

E

Existing to remain

D

Existing to demolish

F

Future work

T

Temporary work

M

Items to be moved

X

Not in contract

1-9

Phase numbers

The use of the Status (Phase) code should be limited, since it can significantly increase the number of levels/layers in a model file. Most items can be shown through referenced model files or changing the line style of items. For instance, New Work can be shown in the current model file; Existing to Remain items can be shown through a screened reference file. Not in Contract items and Future Items could be shown with a dashed line style. Therefore, it is up to the to determine whether the use of the Status (Phase) code in level/layer names increases the readability of the model file. Border sheet model files

As mentioned before, a model file contains information that can be referenced by other disciplines to create other model files or final sheet files. Border sheets are referenced by all disciplines to create sheet files; therefore border sheets are model files. A border sheet model file contains border sheet linework, the title block, and project-specific symbols and text. Typically, each discipline will use the same border sheet and fill in sheet-specific information within the title block or revision block prior to printing the final sheet file (e.g., sheet number, designer names). Reference files (XREFs)

Reference files (external references or XREFs) enable designers to share drawing information electronically, eliminating the need to exchange hard copy drawings between the design disciplines. With the use of reference files, the structural engineer need not wait for the architect to complete the architectural floor plans before beginning the structural framing plan model file. Referencing electronic drawing information makes any changes later made by the architect apparent to the structural designer. This real-time

46

Chapter 4

Level/Layer Assignments

access to the work of others ensures accuracy and consistency within a set of drawings and helps promote concurrent design efforts. No longer does one discipline have to wait until another discipline is nearly finished before they begin their drawings. However, the use of level/layer assignments is a key component in the successful use of reference files. Proper use of levels/layers allows others to use the information in various model files efficiently by allowing levels/layers to be turned on only for the desired graphics.

Sheet Files Sheet files are the final project sheets that are ready to be plotted. A sheet file contains sheet-specific information (e.g., north arrows, scales, section cuts, title block information) in a sheet model (i.e., Paper Space for AutoCAD s). A design model inside the sheet files contains the model information assembled as it would be displayed on a sheet. This model would have real-world spatial alignment and would be used as the primary model for graphical information to be displayed and presented in the sheet model. (See Chapter 2 for more on drawing assembly.) Level/layer assignment tables

The level/layer assignment tables in Appendix B present the following (Figure 4-6): •

The levels/layers assigned to each sheet file.

•

An AIA and corresponding ISO format level/layer name for each level/layer.

•

A detailed definition for each level/layer.

•

The recommended presentation graphics associated with each level/layer. This includes the line style, line width, and color.

s should note that the first 13 level/layers of the sheet file type for every discipline are the same, with the exception that the Discipline Designator changes depending on the discipline for that sheet file type. The unique function of these Annotation levels/layers is to contain sheetspecific information. These levels/layers are as follows with ** representing a Discipline Designator (e.g., A-, C-): **ANNO-DIMS Sheet-specific witness/extension lines, dimension terminators, and dimension text. Chapter 4

Level/Layer Assignments

47

Figure 4-6. Sheet file level/layer assignment table

**ANNO-KEYN Sheet-specific keynotes with associated leaders. **ANNO-LEGN Legends and symbol keys. **ANNO-NOTE Sheet-specific notes and general remarks. **ANNO-NPLT Non-plotting graphic information. **ANNO-PATT Sheet-specific patterning and hatching (e.g., keyplan patterning). **ANNO-RDME Read-me information. **ANNO-REDL Redlines. **ANNO-REVS Revisions, amendments, addenda, and modifications. **ANNO-SCHD Schedules. **ANNO-SYMB Sheet-specific symbols (e.g., north arrow, scales). 48

Chapter 4

Level/Layer Assignments

**ANNO-TEXT Sheet-specific text and callouts with associated leaders. **ANNO-REFR An AutoCAD -specific layer for use in attachment of external references (i.e., reference files). Development of sheet files

As mentioned previously, referenced model files are used in the construction of sheet files. The opens the sheet file type from Appendix B that is appropriate to his/her discipline, then references existing model files into a design model. This design model is used to generate the sheet model for that file. At this point, information can be placed on the annotation layers for the model that has been assembled. For example, after the designer assembles the model files and creates the sheet model as described previously in Chapter 2, the designer would have to “turn off” levels/layers within each referenced model file to achieve the desired sheet file. Which method of drawing assembly is to be used determines how additional annotations are placed. In the design model/sheet model option, design-model-specific annotations can be placed in the design model. When a border sheet and the design model are referenced together to form the sheet model, the designer could then place sheet-specific annotations in the sheet model. When the single model approach is taken, the border sheet is referenced along with the design model (separate design file) into a sheet model and annotations are then placed in the sheet model. The sheet file levels/ layers such as P-ANNOTEXT would be used to fill in sheet-specific information (e.g., sheet number, designer name). Once the final sheet file is achieved, the resulting file is saved (with all reference files attached).

Chapter 4

Level/Layer Assignments

49

5

Standard Symbology

Introduction A “cell” in MicroStation and a “block” in AutoCAD are groups of graphical elements that can be manipulated as a single entity. Examples of typical cells/blocks are windows, doors, graphic scale keys, furniture, etc. The use of such symbology enhances CADD productivity and provides an excellent opportunity for CADD standardization.

Electronic Version of the Symbology/Elements Deliverables

Within the electronic deliverables available as part of the A/E/C CADD Standard, the following symbology is provided: •

MicroStation cells contained in cell libraries (.cel) and custom line styles contained in resource files (.rsc).

Note: Even though the symbols are provided in cell libraries, for MicroStation V8 each symbol is an individual .dgn file. The .cel files are groupings of those .dgn files. •

AutoCAD blocks, each in an individual drawing (.dwg) file, patterns in a pattern library file (.pat), multilines in a multiline library file (.mln), and custom line styles in a line type library file (.lin).

Line styles

Line style definitions determine the particular dash-dot sequence and relative length of dashes, blank spaces, and the characteristics of any included text or shapes. Working with line styles provides a means of distinguishing the purpose of one line from another.

50

Chapter 5

Standard Symbology

AutoCAD and MicroStation both provide a set of standard line styles, as well as allowing the to define custom line styles. In AutoCAD these custom line styles are defined in a line type library file (.lin) and a multiline library file (.mln). In MicroStation, custom line styles are contained in resource files (.rsc) (see Chapter 3, “Line types/styles” for more information. Note: Custom line styles do not readily translate between systems; therefore s should anticipate that translated custom line styles may revert into their primitive graphics.

Tabulated Version of the Symbology/Elements Graphical presentations of the entire symbology library are shown in Appendix D, “A/E/C CADD Standard Symbology.” The symbology library contains four types of elements: Lines, Patterns, Symbols, and Objects. Lines are defined as a graphical representation of linear drawing features (e.g., utility lines, fence lines, contours). Patterns are defined as repeated drawing elements (e.g., lines, dots, circles) within a defined area. Symbols are defined as MicroStation cells or AutoCAD blocks that are representative of objects (e.g., electrical outlets, smoke detectors). Objects are defined as MicroStation cells or AutoCAD blocks that retain their actual size no matter the scale of the drawing (e.g., 30- by 50-in. desk, 3’-0” door).

Chapter 5

Standard Symbology

51

References Air Force Logistics Command. 1989. Architectural and engineering services for CADD implementation within Air Force Logistics Command. American Institute of Architects. 1988. Architectural graphic standards. 8th ed. New York: John Wiley and Sons. American Institute of Architects. 2005. AIA CAD layer guidelines: U.S. national CAD standard version 3.1. Washington, DC: American Institute of Architects Press. American National Standards Institute. 1972. Graphic symbols for electrical wiring and layout diagrams used in architect and building construction. ANSI Y32.9-1972, Institute of Electrical and Electronics Engineers, New York. American Society for Testing and Materials. 1999. Standard practice for the use of metric (SI) units in building design and construction (Committee E-6 Supplement to E380). ASTM E 621-94. Philadelphia, PA. American Society of Heating, Refrigerating and Air-Conditioning Engineers, Inc. 1997. 1997 ASHRAE fundamentals handbook. Atlanta, GA. American Society of Mechanical Engineers. 1995. Decimal inch drawing sheet size and format. ASME Y14.1-1995. New York. __________. 1995. Metric drawing sheet size and format. ASME Y14.1M-1995. New York. American Society of Plumbing Engineers. 1998. Data book Volume 1: Fundamentals of plumbing engineering. Chicago, IL. Construction Metrication Council. 1998. Construction metrication. Vol 7, Issue 1. Washington, DC: National Institute of Building Sciences. Construction Specifications Institute. 2004. Uniform drawing system. Alexandria, VA. Department of Commerce/Department of Defense. 1997. United States of America nautical chart symbols, abbreviations, and . 10th ed. Washington, DC: Department of Commerce.

52

References

Headquarters, U.S. Army Corps of Engineers. 1990. Standards manual for U.S. Army Corps of Engineers Computer-Aided Design and Drafting (CADD) systems. Engineer Manual 1110-1-1807. Washington, DC. International Organization for Standardization. 1982. Technical drawings — General principles of presentation. ISO 128. Switzerland. __________. 1998. Technical product documentation - Organization and naming of layers for CAD - Part 2: Concepts, format and codes used in construction documentation. ISO 13567-2. Switzerland. National Fire Protection Association. 1999. Standard for fire safety symbols. NFPA 170. Quincy, MA. National Institute of Building Sciences. 2005. United States National CAD Standard. Washington, DC. Naval Facilities Engineering Command. 1993. Policy and procedures for electronic deliverables of facilities computer-aided design and drafting (CADD) systems. MIL-HNDBK-1006/7. Alexandria, VA. Sheet Metal and Air Conditioning Contractors’ National Association. 1995. HVAC duct construction standards-metal and flexible. 2nd ed. Chantilly, VA. The CADD/GIS Technology Center. 2001. A/E/C CADD standard: Main text and appendices A-D. Vicksburg, MS: U.S. Army Engineer Research and Development Center.

References

53