Boson Netsim 8.0 25665w

Boson NetSim 8.0 (Full Version) | 87.34MB | Patch included minimum requirements Windows XP NetSim for CCNP 8.0 is designed to help you learn the Cisco IOS command structur e, and it s the technologies and skills required for the recently revised CCNP certification. NetSim for CCNP includes new labs for the ROUTE, SWITCH and TSHOOT technologies. In addition to new content, NetSim for CCNP 8.0 contains a new and improved int erface that makes completing labs, compiling new labs and deg network topo logies easier than ever before. The network topology, device consoles and lab in structions can share the screen in NetSim 8.0 with easy-to-use panes. NetSim 8.0 also s multiple monitors. Everything you need to create and compile new labs from the NetMap topology desi gner, to the device configuration window, to the saving and merging of files are all in one easily navigable window. Completing NetSim labs and creating your ow n labs have never been so easy. Additional Resources NetSim 8.0 Manual. (Best viewed when using Acrobat viewer.) How to compile a lab using NetSim 8.0. (PDF) NetSim for CCNP 8.0 Enhancements Vastly improved interface External lab document viewer enables the use of multiple monitors Telnet mode enables the to open a separate Telnet session for each device i n the simulated topology New labs ing ROUTE, SWITCH and TSHOOT technologies s EIGRP debugging Improved EIGRP less processor intensive for HSRP, MHSRP and VRRP Boson NetSim for CCNP 8.0 Network Simulator Offers Hands-on experience without the hardware A Network Designer that s 42 routers and 6 switches Up to 200 devices per network Virtual Packet Technology: software-created packets that are routed and switched through the simulated network The ability to populate the WAN slots with a broad range of Network Modules A Telnet mode that allows you to configure devices in the simulated topology usi ng the Windows telnet program The functionality of a full rack of equipment on your laptop Automatic lab-grading capability The ability to load and save your network configurations The ability to paste real router configurations into the devices The ability to configure your own ISDN and Frame Relay switch mappings The benefit of connecting your devices over simulated WANs without expensive ISP gear for IPv6 addressing NetSim for CCNP 8.0 Devices 42 Routers (Cisco devices) 6 Switches (Cisco devices) 5 PCs: TFTP, Traffic generator, AAA Server, VPN Client, workstation 1 IP Phone 48 total Cisco devices 54 total devices New CCNP Labs Include

Configuring EIGRP III EIGRP and Frame Relay Influence EIGRP Path Selection Optimizing EIGRP EIGRP Authentication Configuring Hot Standby Router Protocol Configuring Virtual Router Redundancy Protocol Configuring Multiple Hot Standby Router Protocol Troubleshooting EIGRP Routing Troubleshooting Hot Standby Router Protocol Configuring Hot Standby Router Protocol (HSRP) Configuring Virtual Router Redundancy Protocol (VRRP) Configuring Multiple Hot Standby Router Protocol (MHSRP) Labs for CCNP 2950 Deleting VLANs 2950 IP Addresses 2950 Spanning Tree 2950 Telnet 2950 Trunk 2950 VLANs 2950 VTP 2950 VTP with Client AAA AAA Authentication and Exec Authorization Access List Review Address Optimization Advanced Access Lists Advanced Router Config Applying Security Tools ARP Backing up a WAN Connection with IPSEC VPN Backup Interface Backup Using TFTP Basic Router Config Basic Show Commands BGP Catalyst 1900 Switch Config Catalyst 2950 Switch Config CDP CHAP and RIP Router Cisco Discovery Protocol Configuring a Switch for a WLAN Configuring Class-Based Header Compression Configuring EIGRP I Configuring EIGRP II Configuring EIGRP III Configuring FIFO and WFQ Queuing Mechanisms Configuring Frame Mode MPLS Configuring GRE Tunnels over IPsec using SDM Configuring Hot Standby Router Protocol Configuring IOS Security Part 1 VLAN ACL s Configuring IOS Security Part 2 TACACS+ Configuring IPv6 Configuring IPv6 Routing Configuring IPv6 Tunnels Configuring LFI Configuring Multiple Hot Standby Router Protocol Configuring NBAR Configuring OSPF

Configuring QoS Configuring QoS Preclassify Configuring QoS with Cisco AutoQoS Configuring Router Interfaces Configuring Static and OSPFv3 Routing Configuring for IP Telephony Configuring Switch Interfaces Configuring the LLQ Queuing Mechanism Configuring Virtual Router Redundancy Protocol Connectivity Test with TraceRoute Creating a Host Table Default Routes Demo Lab EIGRP and Frame Relay EIGRP and Wildcard Masks EIGRP Authentication I EIGRP Authentication II EIGRP Routes Extended Access Lists Extended Access Lists with RIP Frame Relay Frame Relay Full Mesh Frame Relay Hub-and-Spoke Frame Relay with Dial Backup Hierarchical IP Addressing IGRP IGRP Routes Implementing Multiple Spanning Tree Protocol Implementing NAT Implementing NAT II Influence EIGRP Path Selection Inter VLAN Routing Initial Config Introduction to MQC and the SDM QoS Wizard IOS Switching Initial Configuration IP Access Lists IP Addressing IPSEC ISDN ISDN BRI ISDN BRI-BRI Using Dialer Profiles ISDN BRI-BRI Using Legacy DDR ISDN Dialer Profiles ISDN PRI Using Dialer Profiles IS-IS Lab Primer Layer 3 Switching Layer 3 Switching and Layer 2 Security Loopback Interfaces Low Latency Queuing Many-to-One NAT Multi-Area OSPF Multi-Area OSPF and Routing Table Optimization Multicast Routing Multi-Site Frame Relay and Policy Routing Multi-Site Network Named Access Lists NAT This Product Covers: Certification

640-802 640-822 640-816 642-813 642-832 642-902

CCNA ICND1 (Interconnecting Cisco Networking Devices Part 1)-CCENT ICND2 (Interconnecting Cisco Networking Devices Part 2)-CCNA SWITCH-CCNP TSHOOT-CCNP ROUTE-CCNP