Engineering Drawing Lab Manual 223v53
This document was ed by and they confirmed that they have the permission to share it. If you are author or own the copyright of this book, please report to us by using this report form. Report 3b7i
Overview 3e4r5l
& View Engineering Drawing Lab Manual as PDF for free.
More details w3441
- Words: 8,201
- Pages: 52
ENGINEERING GRAPHICS (2013-2014)
MAHARAJA AGRASEN INSTITUTE OF TECHNOLOGY ENGINEERING GRAPHICS (2013 (2013-2014) 2014) LAB MANUAL
NAME: - __________________ _______________________________ _____________ ROLL NO: - ________________ ___________________________ ______________ GROUP: - ____________________________ _______________________________ BRANCH: - __________________________ ______________________________ GROUP TEACHER:________________________ For video lecture: www.CrazyProf.in
Page 1
ENGINEERING GRAPHICS (2013-2014)
GENERAL INSTRUCTIONS FOR ENGG. GRAPHICS LAB. (ETME-159) 1) Students are required to draw sheet in the class (lab) itself.
2) 3)
4) 5) 6)
7)
8)
Students can take back their sheets only after final evaluation. On being absent in the lab, the sheet will not be assessed and will be awarded zero (0). Each student should get their sheets checked on the same day, otherwise it will be considered as late work and will be evaluated out of 5 marks. Name & Roll No. should be written in Ink i.e. with PEN. Each student should make at least 11 drawing sheets in the whole semester. 10 marks will be awarded by the faculty concerned on the basis of performance of the student in quiz and 10 marks for internal viva-voice. At the end of the semester, best of 10 sheets shall be considered for final assessment. These 100 marks will be converted into 20 marks. At the time of external examination, all the sheets shall be submitted to the faculty concerned as below: a. All the sheets should be properly arranged in the serial order. b. All the sheets should be rolled together in a Plastic Sheet Holder.
For video lecture: www.CrazyProf.in
Page 2
ENGINEERING GRAPHICS (2013-2014) SYLLABUS Paper Code: ETME-159 Paper: Engineering Graphics Lab
L 0
P 2
C 1
UNIT - I General: Importance, Significance and scope of engineering drawing, Lettering, Dimensioning, Scales, Sense of proportioning, Different types of projections, Orthographic Projection, B.I.S. Specifications, Projections of Point and Lines: Introduction of planes of projection, Reference and auxiliary planes, projections of points and Lines in different quadrants, traces, inclinations, and true lengths of the lines, projections on Auxiliary planes, shortest distance, intersecting and nonintersecting lines.
UNIT - II Planes other than the Reference Planes: Introduction of other planes (perpendicular and oblique), their traces, inclinations etc., Projections of points and lines lying in the planes, conversion of oblique plane into auxiliary Plane and solution of related problems. Projections of Plane Figures: Different cases of plane figures (of different shapes) making different angles with one or both reference planes and lines lying in the plane figures making different given angles (with one of both reference planes). Obtaining true shape of the plane figure by projection.
UNIT - III Projection of Solids: Simple cases when solid is placed in different positions, Axis faces and lines lying in the faces of the solid making given angles. CADD
UNIT - IV Isometric Projection Nomography : Basic Concepts and use.
TEXT BOOKS: 1. Engineering drawing by N.D.Bhatt (Charotar Publications). 2. Engineering Graphics by Roop Lal & Ramakant Rana (Acme Learning Publications).
REFERENCE BOOKS: 1. Engineering Drawing by Venugopalan. 2. Engineering Drawing by P.S.Gill
For video lecture: www.CrazyProf.in
Page 3
ENGINEERING GRAPHICS (2013-2014)
SHEET NO.: 1 INTRODUCTION Introduction: Technical drawing is the language of engineers. It is graphical language which is universally accepted and used. Without the knowledge of engineering drawing, an engineer is unable to communicate his ideas and eventually would not have been able to construct the various magnificient structures or design intricate machinery. Therefore anyone connected in anyway with engineering construction, must understand this language of engineers. Technical drawing is therefore indispensable today and shall continue to be as long as engineering and technology continue to be part of human activities. The subject engineering graphics will help the students in many ways from drawing images images, describing the shape, size, finish, colour and finally constructing any object. Student will learn the basic concept of orthographic projection, projection of points, lines, planes, solids, section of solids, and development of surfaces of solids and Isometric projections. To express their ideas. This understanding will also help them in interpreting the expressions of others. Engineering Drawing is a universal graphic language of the engineers. It is used by them to develop and record their ideas and transmit them to others for execution. Every language has its own rules of grammar. Engineering Drawing also has its grammar in the theory of projection, its punctuation in the types of lines, its abbreviation’s, symbols & descriptions in the constructions. NEED & SCOPE OF ENGINEERING GRAPHICS: Engineering drawing offers students an insight into the methods to tackle engineering problems. It teaches us the principle of accuracy, exactness & positiveness with regards to the information necessary for the production of the engineering components. It develops the engineering imagination i.e. so essential for creation of successful design. Drawing Sheet: There are different qualities of papers available in the market. Quality of paper to be used depends upon the nature of drawing. The drawing sheet should be uniform in thickness, of such a quality that the erasing marks are not visible and the ink should not spread out. One side of the drawing sheet is rough and other side is smooth. Smooth side is used for drawing work. Sizes of Drawing Sheet: Standard sizes of trimmed and untrimmed sheets according to BIS are given in the table no.1.1:
For video lecture: www.CrazyProf.in
Page 4
ENGINEERING GRAPHICS (2013-2014)
For video lecture: www.CrazyProf.in
Page 5
ENGINEERING GRAPHICS (2013-2014) Layout of drawing Sheet: Given specification are to be followed before commencing the sheet work.
Note Note: all dimensions are in mm
Lists of drawing instruments: instruments:The following set of drawing instruments and materials are required in the preparation of engineering drawing sheet. 1. Drawing board (provided) 2. Drawing sheet(A-2 Size) 3. Mini Drafter 4. Instrument box containing com and dividers 5. Set squares 6. Drawing pin or clips or cello tape (30°-60°, 45°-45°) 7. Protractor 8. Drawing pencils (HB, H, 2H) 9. Eraser, Sharpener, Scale, 10. Plastic Sheet Holder. Circle Master, Dusting Cloth. Convention of lines: For video lecture: www.CrazyProf.in
Page 6
ENGINEERING GRAPHICS (2013-2014)
Arrow Head:
For video lecture: www.CrazyProf.in
Page 7
ENGINEERING GRAPHICS (2013-2014) It is used as terminator on dimension lines. The points of the arrow heads on leader lines and dimension lines must make the with the feature object line or extension line which represents the feature being dimensioned. The standard size ratio for all arrow heads on mechanical drawings is 3:1 (Length to Width).
Figure1.2: Dimensioning
For video lecture: www.CrazyProf.in
Page 8
ENGINEERING GRAPHICS (2013-2014) Dimensioning: 1. Dimensions should be placed outside the views, except when they are cleaner more easily readable inside. 2. Dimension lines should not cross each other 3. As far as possible, dimension should not be shown between the dotted lines. 4. Dimension lines should be placed at about 6mm from the outlines. 5. Head should be pointed and filled in. they are made in ratio 3 to1 (Length) Lettering: - Writing titles, dimension, notes and other important particulars on a drawing is called lettering should therefore be done properly in clear, legible and uniform style preferably freehand and speedily. Types of letters:1. Single stoke letters:- in these letters, the thickness o line of the letter should be such as is obtained in one stoke of the pencil Single stoke letters of two types:(1) Vertical (2) Inclined Inclined letters lean to the right at angle of with the horizontal. The ratio of height to width various but in case of most of the letters it is 7:4. These are shown in following figure Gothic letters: - if stems of single stroke letters, are given more thickness, the letters are known as gothic letters.
For video lecture: www.CrazyProf.in
Page 9
ENGINEERING GRAPHICS (2013-2014)
QUESTION OF SHEET NO.1 1. Write alphabets in capital and numerals in single stroke with 7:4 ratio only (Without Using Scale). 2. Draw the Conventional of lines with there description. 3. Draw the Figure No.1.2 with proper dimensioning as per rules.
For video lecture: www.CrazyProf.in
Page 10
ENGINEERING GRAPHICS (2013-2014)
Sheet No.: 2 PROJECTION OF POINTS Projection: If straight lines are drawn from various points on the contour of an object, to meet a plane of projection, the object is said to be projected on that plane. The figure formed by ing, in correct sequence. The he points at which these lines meet the plane of projection, is called projection of the object. The line from the object to the plane of projection is called project projectors as shown in following figure:
Figure 2.1: Projection Orthographic Projection Projection:: When projectors are parallel to each other and also perpendicular to the plane of projection the projection is called Orthographic projection. The necessary condition for orthographic projections is that the observer should be at infinite distance w.r.t. object. For video lecture: www.CrazyProf.in
Page 11
ENGINEERING GRAPHICS (2013-2014) Planes of Projection: Two planes used for the orthographic projection are called reference planes or principal plane of projection. They intersect each other at right angles. They are known as:(i) Vertical Plane (VP) (ii) Horizontal Plane (HP) The vertical plane is often called the frontal plane and denoted by the letters F.P. Projection on vertical plane (VP) is called front view or elevation. Projection on the HP is called the top view or the plan. The line of intersection of vertical plane and Horizontal Plane is called reference line and is denoted by letter XY. Profile Plane: A plane perpendicular to HP and VP is called profile plane. Projection on profile plane is called side view or end view. Four Quadrants: When the planes of projection are extended beyond the line of intersection, they form four quadrants or dihedral angles. They are numbered as first, second, third and fourth quadrant. The object may be situated on any one of the quadrants. The position of the object relative to planes is described as above or below HP in front of or behind the VP. The planes of projections are assumed to be transparent. The projections are obtained by drawing projectors from the object to the planes (VP and HP) by looking from the front or from the above. The quadrants are shown in figure 2.2.
For video lecture: www.CrazyProf.in
Page 12
ENGINEERING GRAPHICS (2013-2014)
Figure 2.2 2.2: The four Quadrants When the object lies in the first quadrant; it means it may lie: • Above HP and in front of VP • Or on HP and in front of VP • Or on VP and above HP When the object lies in the second quadrant, it means it may be: • Above HP and behind VP • Or on HP and behind VP • Or above HP and on VP When the object lies in the third quadrant, it means it may be: • Below HP and behind VP • On HP and behind VP • Below HP and on VP When object lies in the fourth quadrant, it means it ma mayy be: • Below HP and front of VP • On HP and in front of VP • Below HP and on VP
For video lecture: www.CrazyProf.in
Page 13
ENGINEERING GRAPHICS (2013-2014)
Figure 2.3:: Front View (Elevation) & Top View (Plan) First Angle Projection:: (i) The object lies between observer and plane of projection. (ii) In this method, when views are drawn in their relative position, the top view comes below the front view. In other words, the view seen from above is placed on other side (i.e. below) the front view. (iii) Similarly left hand and view is drawn on the right side of front view and right hand side view is drawn on the left of front view. Convention of first angle projection:
Third Angle Projection: (i) Plane of Projection is lies between object and observer. (ii) In this method, when views are drawn in their relative position, the top comes above the front view. In other words, the view
For video lecture: www.CrazyProf.in
Page 14
ENGINEERING GRAPHICS (2013-2014)
(iii)
seen from above is placed on the same side (i.e. above) of front view. Left hand end view is drawn at left hand of front view and right hand end view is drawn at the right side of front view.
Convention of third angle projection
Note: Students are required to draw on drawing sheets in 1st Angle Projection. ode of practice for general engineering Drawing, As per Indian code published ed in 1973, the committee responsible for preparation has left the option of selecting first or third angle projection method to s. Projection of points in different quadrants 1. Point A is h mm above HP and g mm in front of VP. Point A is in first quadrant.
2. Point B is in the h mm above HP and g mm behind VP. Hence B in the second quadrant.
For video lecture: www.CrazyProf.in
Page 15
ENGINEERING GRAPHICS (2013-2014)
To draw a projection i.e. front view b’ and top view b on the paper, once the third quadrant is open, HP coincide with VP and both HP & VP are above the XY line. 3. Point C is h mm below HP and g mm behind VP. Hence point C in the third quadrant.
To draw the projections (c’ and c) on the paper, once the third quadrant is open, HP lies above XY line and VP below the XY line and draw top view above the XY line and front view below the XY line. 4. Point D is h mm below HP and g mm in front of VP. Hence point D is in the fourth quadrant. To draw projections (Front view d’ and top view d), once the 1st quadrant is opened, HP concedes with VP and both will be below the XY line. Hence front view and top view will be below the XY line.
For video lecture: www.CrazyProf.in
Page 16
ENGINEERING GRAPHICS (2013-2014)
Note: (i) (ii)
Distance of the point above the HP or below the HP indicate the position of front view. Distance of the point in front of VP or behind VP indicate the position of top view.
For video lecture: www.CrazyProf.in
Page 17
ENGINEERING GRAPHICS (2013-2014)
QUESTION OF SHEET NO.2 1.
Draw the projections of the following points taking common reference line, keeping the distance between any two consecutive points as 20mm. (i) Point A 35 mm in front of VP and 35 mm above HP. (ii) Point B is in HP and 30 mm in front of VP (iii) Point C is 30 mm above HP and 45 mm behind VP. (iv) Point D is in VP and 45 mm above HP. (v) Point E is 35 mm below HP and 55 mm behind VP (vi) Point F is in VP and 45 mm below HP. (vii) Point G is both HP and the VP.
2.
A point P is 15 mm above HP and 20 mm infront of VP. Another part Q is 25 mm behind the VP and 40 mm below HP. Draw the projections of P and Q, keeping the distance between their projectors 75 mm, draw straight lines ing their (i) top views (ii) Front views.
3.
Two point A and B are in HP. Point A is 30 mm infront of VP, while B is behind the VP. The distance between their projectors 75 mm and line ing their top views makes an angle of 45° with XY. Find the distance of the point B from the VP.
4.
A point P is 25 mm below HP and its shortest distance form XY(reference line) is 50mm. the point P lies in the third quadrant. Draw its projection.
For video lecture: www.CrazyProf.in
Page 18
ENGINEERING GRAPHICS (2013-2014)
SHEET NO.:3 PROJECTION OF STRAIGHT LINES-I A straight line is the shortest distance between the two points. Hence projection of straight line may be drawn by ing the respective position of its ends, which are points. The position of straight line is described with reference two reference planes. It may be 1. Parallel to HP and VP. 2. Perpendicular to HP and parallel to VP or perpendicular to VP and parallel to HP. 3. Inclined to HP and parallel to VP or Inclined to VP and parallel to HP. 4. Inclined to HP and VP.
I. A line AB is parallel to HP and VP Since line AB is parallel to HP and VP. Its front view a`b` and top view ab will show true length of line AB and will be parallel to XY line
II. A line AB is perpendicular HP and parallel to VP Since a line is perpendicular to HP. It will be automatically parallel to VP since it is parallel to VP, front view will show true length of line AB and top view will be a point, where points a & b will meet.
For video lecture: www.CrazyProf.in
Page 19
ENGINEERING GRAPHICS (2013-2014) III. A line AB is perpendicular to VP and parallel to HP. Since the line AB is parallel to HP. Top view will show true length of line AB and will be perpendicular to any line. Front view will be point, where both points a and b will meet.
IV. A line AB is Inclined to HP and parallel to VP. Since the line AB is parallel to VP. From view will show true length of line and true inclination with HP so knowing the position of point A (as given in question) projection of end A are drawn. From the point A, line a`b` is drawn equal to length of line AB at an angle Ɵ with HP since the line AB is parallel to VP, top view ab will be parallel to XY.
A line AB included to VP and parallel to HP. Since the line AB is parallel to HP. Top view ab will show true length of line AB and true inclination with VP (ɸ). Projection of points A as per given in the question drawn as a’ and a. Draw line ab as top view at angle ɸ with VP. Front view a`b` will be parallel to xy line. V.
For video lecture: www.CrazyProf.in
Page 20
ENGINEERING GRAPHICS (2013-2014)
QUESTION OFSHEET NO.3 1. Straight line AB 40 mm long makes an angle of 30 to the HP. The end A is 10 mm above the HP and 15 mm infront of the VP. Draw the top view and front view of the line AB. 2. Straight line AB 60 mm long makes an angle of 55 to the VP and 25 to the HP. The end A is 10 mm above the HP and 10 mm infront of the VP. Draw the projections of the line AB. 3. Straight line AB 60 mm long makes an angle of 55 to the VP and 25 to the HP. The one end of the straight line AB lies in the HP and is 20 mm infront of the VP. Draw the projections of the line AB. 4. A straight line AB is 50 mm long. Its one end A is 40 mm from the H.P. and 10 mm from V.P. and other end B is 30 mm from the V.P. and 20 mm from the H.P. Draw the projections.
For video lecture: www.CrazyProf.in
Page 21
ENGINEERING GRAPHICS (2013-2014)
Sheet No.:4 PROJECTION OF STRAIGHT LINES-II A given line may be inclined to both the reference planes i.e. HP and VP. In such cases, length of line and its inclination with HP and VP may be given; it may be required to draw its projections. In another case, projections of line may be given, and it may required to determine its true length and its inclinations with HP an VP. I Case:
Length of line AB and its inclination and with HP and with VP are given. Position of point A is also given. Projections are to be drawn.
a’b’1 = Front view of Line AB ab1 = Top view of Line AB Procedure: - Draw the front view a’ and top view a of the point A as per given question:- From a’ draw line a’b’ equal to true length of line AB and at angle Ɵ with the HP. - From the point a, draw a line ab equal true length of line AB and at angle ɸ with VP. For video lecture: www.CrazyProf.in
Page 22
ENGINEERING GRAPHICS (2013-2014) - Draw locus ef, rs, pq and cd from the b’,a’, a and b respectively, parallel to XY line. For example ef is locus of point b’. - If a’b’ is true length of line AB a’b’2 projected length of a’b’ and is equal to length of top view of line AB. - Further project the point b’2 on locuslinepq such that a’b2 = ab2 = length of top view. - Now bring the point b2 on the locus of point b i.e. line cd. Take a as centre and radius equal to ab2, draw arc b2b1. a to b1. ab1 is the length of top view. - Similarly of ab is true length of line AB, ab3 = a`b`3 = length of front view. - Take a’ as centre and radius equal to a`b`3, and draw arc b3’b1’ to bring point b3’ on locus of point b’ i.e. ef a’ to b’1 Hence ab3 = a’b3’ = a’b’1 = length of front view. Note: Point b1 and b1’ projections of point b should lie on the same vertical line. II Case:
Determination true length of a line and its inclination with HP and VP when projections are given.
Front view a’b’ and top view ab of line AB are given. Determine true length of line AB and inclination Ɵ with HP and ɸ with VP. Problem can be solved by two method. (i) Method of rotation. (ii) Trapezoid Method.
METHOD OF ROTATION Principle: Now if front view a’b’ is made parallel to XY, the line AB becomes parallel to HP and its projection ab1 on HP shows its true length and true inclination with VP. For video lecture: www.CrazyProf.in
Page 23
ENGINEERING GRAPHICS (2013-2014) Similarly if top view ab of line AB is made parallel to VP, the line AB becomes parallel to VP and its projection on VP show its true length and true inclination with HP
Procedure: Draw locus of point b’,a’, a and b i.e. lines ef, rs, pq and cd respectively parallel to XY. Take a’ as centre and radius equl to a’b’ and draw arc b’b2’ to make front view a’b’ parallel to XY and line AB becomes parallel to HP. Project point b2’ on the locus of point b. a to b1. ab1 is true length of line AB and show true inclination ɸ with VP. Similarly take a as centre and radius equal to ab, draw an arc bb2, to make top view ab parallel to XY. Now line AB becomes parallel to VP and its projection on VP shows its true length and true angle of inclination with HP.
TRAPEZOID METHOD Procedure: Draw the projections i.e. front view and top view of line AB as per question. A the point a’ draw perpendicular a’A’ equal to distance of point A from XY. Further draw perpendicular b’B1 equal to distance of b from XY line. A1 to B1. A1B1 shows true length of line AB. Line A1B1 and a’b’ will make angle ɸ, inclination with VP if extended back. For video lecture: www.CrazyProf.in
Page 24
ENGINEERING GRAPHICS (2013-2014)
Similarly draw perpendicular aA2 at a equal to distance to distance of a’ from XY. Further draw perpendicular bB2 at b equal distance of b’ from XY A2 to B2. A2B2 shows the true length of line Ab. Line ab and A2B2 will make angle Ɵ, inclination with HP if extended back. Traces of a Line: When a line is inclined to a plane, it will meet that plane produced if necessary. The point of intersection of line and plane is called trace. Horizontal Trace (HT): If a line is inclined to HP, it will meet Horizontal plane then the point of intersection of line and HP is called horizontal trace (HT). Vertical Trace (VT): If a line inclined to VP; it will meet the vertical plane. The point of intersection of line (produced back if necessary) with the VP plane is called vertical trace. Note 1: If a line is inclined to HP and VP. A will have both HT and VT. Note 2: If a line is parallel to any reference plane it will have not trace with that plane.
For video lecture: www.CrazyProf.in
Page 25
ENGINEERING GRAPHICS (2013-2014) Determining Traces of A Line: (1) A line AB is inclined to HP and parallel to VP Draw the front view a’b’ and top view ab of line. Angle of inclination Ɵ with HP is shown by front view. Produced back front view a’b’ till it intersect XY line at point C. From C draw perpendicular on top view ab (produced back) at a point called HT.
(2) A line AB is inclined to VP and parallel to HP Draw the projections (Front view a’b’ and top view ab) of line ABM Angle of inclination ɸ with VP is shown by its top view. Produce back top view ab till it cuts the XY line at D. From D draw perpendicular on the extended front view a’b’. Point of intersection of front view and perpendicular from D is the vertical trace.
For video lecture: www.CrazyProf.in
Page 26
ENGINEERING GRAPHICS (2013-2014) (3)
A line AB is inclined to HP and VP:
Draw the projections (front view a’b’ and top view ab) of line AB. Produce back front view a’b’ till it cut the XY line at C. From C draw perpendicular on extended top view to get HT. Produce back top view ab. It cuts the XY line at D. From D draw perpendicular on the extended front view to get VT.
For video lecture: www.CrazyProf.in
Page 27
ENGINEERING GRAPHICS (2013-2014)
QUESTION OF SHEET NO. 4 PROJECTIONS OF LINES – II 1. A line AB, 65mm long, has its end A 20mm above HP and 25 in front of VP. The end B is 50mm above HP and 65 mm in front of VP. Draw the projections of line AB and show its inclination with HP & VP (Rotational Method). 2. A line AB has its end A 7 mm behind VP and 18mm below HP. The end B 38mm behind VP and 49mm below HP. The distance between the end projectors is 37mm. Draw the projection of line and find out , ∅, HT, VT & TL (Rotational Method). 3. The distance between the projectors of a line is 40 mm. The end A is 20 mm away from HP and 30 mm away from VP & the end B is 50 mm away from HP and 10 mm away from VP. Draw the projection of line AB and determine its , ∅, HT, VT & TL (Trapezoid Method). 4. The end A of line AB is in the HP and 25mm behind VP. The end B is in the VP and 50mm above the HP. The distance between the projectors is 75mm. Draw the projections of line AB, and determine its true length, traces, inclination with HP & VP (Trapezoid Method).
For video lecture: www.CrazyProf.in
Page 28
ENGINEERING GRAPHICS (2013-2014)
SHEET NO.: 5 PROJECTION OF PLANES Plane Surfaces: Plane surfaces have only two dimensions i.e. length and breadth. They do not have thickness. A plane surface may have triangular, rectangular, square, pentagonal or hexagonal shape. Types of Planes: Plain may be divided in two main types:(i) Perpendicular planes (ii) Oblique planes Perpendicular planes can be sub divided into following sub types: (a) Perpendicular to both the reference planes (b) Perpendicular to one reference plane and parallel to other (c) Perpendicular to one reference plane and inclined to other Oblique Planes: Planes which are inclined to both the reference planes are called oblique planes. Traces of Planes: If a plane is perpendicular or inclined to a reference plane, the line in which plane surface meet with reference plane is the trace of plane. The line in which, the plane meet the HP, is called Horizontal Trace (HT). The line in which it meets with VP is called vertical trace (VT). Perpendicular Planes: (i) A square plane is perpendicular to HP and VP: Projection are shown in fig. 5.1
For video lecture: www.CrazyProf.in
Page 29
ENGINEERING GRAPHICS (2013-2014)
Figure 5.1 (ii) A square plane perpendicular to HP and parallel to VP. Since the plane is parallel to VP front view a’b’c’d’ will show its true shape and top view will be a straight line parallel to XY as shown in fig. 5.2
Figure 5.2 Since the plane is perpendicular to HP, it has HT and no VT, since it is parallel to VP. (iii) A square plane perpendicular to VP and parallel to HP. Since the plane is parallel to HP, top view abcd will show its shape but no HT. Front view will be straight line parallel to XY and it also represent VT as in fig. 5.3
For video lecture: www.CrazyProf.in
Page 30
ENGINEERING GRAPHICS (2013-2014)
Figure 5.3 (iv) A square plane perpendicular to HP and inclined to VP. First assume, the plane is parallel to VO. Draw front view a’b’c’d’ first and project top view from the front view. In the second stage, rotate top view ad-bc at angle ɸ, inclination with VP. New top view will be ad – b1c1 Project points b1c1 to get point b’1 and c’1 in the front view to get final front view a’b’1c’1d’.
Figure 5.4
For video lecture: www.CrazyProf.in
Page 31
ENGINEERING GRAPHICS (2013-2014) (v) A square plane perpendicular to VP and inclined to HP First assume parallel to HP and perpendicular to VP top view abcd will show the true shape of square plane. Project front view a’d’-b’c’ from top view.
Figure 5.5 In the second stage rotate front view a’d’ –b’c’ by an angle Ɵ, inclination with HP to get new front view a’d’-b’1c’1. Project the point b’1c’1 on top view to get point b1 and c1 and to get new top view ab1c1d. (vi) Oblique Planes: The projection of planes, inclined to both the reference planes is drawn in three stages as per the conditions given in the question.
For video lecture: www.CrazyProf.in
Page 32
ENGINEERING GRAPHICS (2013-2014)
QUESTION OF SHEET NO.5 1.
A regular pentagon of 25 mm side has one of its side in the HP. Its plane is inclined at 450 to HP and perpendicular to VP. Draw its projections.
2.
To project the front view and top view of a hexagon ABCDEF of 25 mm side with its base on or above H.P. and inclined to V.P. at 600.
3.
A circular plate (ABCDEFGH) of diameter 80 mm is 15 mm above HP such that it makes an angle 300 to the HP. The top view of diameter DH makes an angle of 600 with VP. Draw the projections.
4.
A square ABCD of 50 mm side has its corner A on the HP. Its diagonal AC is inclined at 300 to HP and its diagonal BD is inclined at 450 to VP and parallel to HP. Draw its projections.
For video lecture: www.CrazyProf.in
Page 33
ENGINEERING GRAPHICS (2013-2014)
SHEET NO.: 6 PROJECTION OF SOLIDS A solid has three dimensions, viz. length, breadth and thickness. To represent a solid on flat surface having only length and breadth, at least two orthographic views are necessary. Sometimes, additional views is projected on Auxiliary planes, if necessary to make the description of a solid complete. Solids may be divided into two main groups:(i) Polyhedra (ii) Solids of revolutions
Polyhedra: Polyhedra are defined as solid bounded by planes called faces. When all the faces are equal and regular, the polyhedron is said to be regular. There are five regular 34olyhedral which may defined as stated below:(i) Tetrahedron: It has four equal faces, each one is equilateral triangle. (ii) Cube or hexahedron: It has six faces, each face is square. (iii) Octahedron: It has eight faces. Each face is an equilateral triangle. (iv) Dodecahedron: It has twelve equal faces and each face is regular pentagon. (v) Icosahedrons: It has twenty faces. Each face is an equilateral triangle.
Prism: Prism is a polyhedron having two equal and similar faces called its ends or bases, parallel to each other and ed by other faces, which are parallelograms. The imaginary line ing the centre of the bases is called axis. A right regular prism its axis perpendicular to the bases. The bases may be triangular, square, pentagonal or hexagonal in shape.
For video lecture: www.CrazyProf.in
Page 34
ENGINEERING GRAPHICS (2013-2014) Accordingly they called as triangular, square, pentagonal hexagonal prism.
Pyramid: Pyramid is a polyhedron having a plane figure as base and number of triangular faces meting at a point called the vertex or apex. The imaginary line ing the apex with the centre of base is its axis. A right and regular pyramid has its axis perpendicular to base which is a regular plane figure. Its faces are equal isosedes triangle. As per shape of the base, they are called as Triangular, square, pentagonal and hexagonal pyramid. TRIANGULAR PYRAMID
For video lecture: www.CrazyProf.in
SQUARE PYRAMID
PENTAGONALPYRAMID
Page 35
ENGINEERING GRAPHICS (2013-2014) SOLID OF REVOLUTIONS: A right circular cylinder is a solid generated by the revolution of a rectangle about one of its sides which remain fixed. It has two circular bases. The ing the center of the bases is the axis. It is perpendicular to the bases. A right circular cone is a solid generated by the revolution of a right angled triangle about one of its perpendicular sides which is fixed. It has one circular base. Its axis the apex with the centre of the base to which it is perpendicular. Straight lines drawn from the apex to the circumference of the base circle are all equal and are called generators of the cone. The length of generator is the slant height of the cone.
CYLINDER
CONE SPHERE Figure 6.1: SOLIDS
A sphere is a solid generated by the revolution of a semicircle about its diameter as the axis. The midpoint of diameter is the centre of sphere.
Frustum of a solid: When a pyramid or a cone is cut by a plane parallel to its base, thus removing the top portion, the remaining portion is called its frustum.
Truncated Solid: When a solid is cut by a plane inclined to the base, it said to be truncated. A solid may be inclined to one or both the reference planes. Accordingly projections are drawn in two and three stages respectively.
For video lecture: www.CrazyProf.in
Page 36
ENGINEERING GRAPHICS (2013-2014)
QUESTION OF SHEET NO.6 1.
Draw the projections of a pentagonal prism, base 25 mm side and 50 mm long, resting on one of its rectangular faces on HP with its axis inclined at 45˚ to VP.
2.
Draw the projections of a cylinder 75 mm diameter 100 mm long, lying on the HP with its axis inclined 30˚ to VP and parallel to HP.
3.
A hexagonal pyramid, base 25 mm side and axis 50 mm long, has an edge of its base on the HP. Its axis is inclined at 30˚ to HP and parallel to VP. Draw the projections.
4.
Draw the projections of a cone, base 75 mm diameter and axis 100 mm long, lying on the HP on one of its generator, with the axis parallel to VP.
5.
Draw the projection of cone, base 50 mm diameter and axis 55 long, when it is resting on the HP on its base circle with the axis making an angle of 30˚ with HP and its top view making 45˚ with the VP.
For video lecture: www.CrazyProf.in
Page 37
ENGINEERING GRAPHICS (2013-2014)
SHEET NO.: 7 SECTION OF SOLIDS In the projected views of an object, invisible features are shown by dotted lines. But when such features are too many, these lines make the view more complicated and difficult to interpret. In such cases, it is customary to imagine the object as being cut through or sectioned by planes. This imaginary plane is called the sectioned plane or the cutting plane. The part of the object between cutting plane and observer is assumed to be remove and the view is than shown in sections The projection of the section along with remaining portion of the object is called sectional view. The surface produced by cutting the object by the section plane is called the section. It is indicated by thin section line uniformly spaced and inclined at 45o. Section planes:- section planes or cutting planes are generally perpendicular planes. They may be perpendicular to one of the reference planes and either perpendicular parallel or inclined to other reference plane. They are usually described by their traces. It is important to note that projection of the section plane, on the plane to which it is perpendicular, is a straight line, this line will be parallel, perpendicular or inclined to XY, depending upon the section plane being parallel, perpendicular, or inclined respectively to other reference plane. This straight line coincides with the trace of section plane. True shape of the section:The projection of the section on a reference plane, parallel to the section plane, will show the true shape of the section. Thus when, section plane is parallel to HP, the true shape of the section will be seen in sectional top view. When it is parallel to VP, the true shape will be visible in the sectional front view. But when the section plane is inclined the section has to be projected on an auxiliary plane, parallel to the section plane, to get the true For video lecture: www.CrazyProf.in
Page 38
ENGINEERING GRAPHICS (2013-2014) shape. When the section plane is perpendicular to both the reference planes, the sectional side view will show the true shape of the section.
Table 7.1: Conventions of Materials
For video lecture: www.CrazyProf.in
Page 39
ENGINEERING GRAPHICS (2013-2014)
QUESTION OF SHEET NO.7 1) A right regular pentagonal pyramid side of base 40 mm and ht. 60 mm rest on its base in HP with one of its base edge perpendicular to VP. A section plane parallel to the HP cuts the axis of the pyramid at a distance of 25 mm from its base draw its front view and sectional top view. 2) A right regular pentagonal prism, base edge 40 mm and ht. 70mm is held on HP one of its base edge such that its axis is parallel to the VP and inclined to HP at 30o. An auxiliary horizontal plane cuts the prism, intersecting its axis at a distance of 17 mm from its top end. Draw its front view and sectional top view. 3) A right regular pentagonal pyramid, side of base 40mm and ht. 70mm, rest on its base on HP, such that one its base edges perpendicular to the VP. A section plane parallel to VP cuts the pyramid and is at a distance of 8mm from the axis. Draw its top view and sectional front view. 4) A right circular cone diameter of base 60mm and ht. 70mm, rest on its base on HP. A section planes perpendicular to VP and inclined to HP at 45o, cuts the cone meeting its axis at the distance 36mm from its base. Draw its front view, sectional top view and true shape of section.
For video lecture: www.CrazyProf.in
Page 40
ENGINEERING GRAPHICS (2013-2014)
SHEET NO.: 8 ORTHOGRAPHIC PROJECTION - 1 PROJECTIONS AND PROJECTION LINES (PROJECTORS): When different straight lines are drawn from various points on the contour of the object on to the plane of drawing sheet, the figure obtained on the sheet by ing different points in the correct order is known as Projection of that object (Refer the Following Figure 8.1). And the lines drawn from various points on thecontour of the object on to the plane of drawing sheet are called Projectors or Projection Lines.
Figure 8.1: Projection and projection lines ORTHOGRAPHIC PROJECTION: The image of the object obtained on the plane of projection when the projectors are from the various points on the object, parallel to each other and perpendicular to the plane of projection, then the image obtained on the plane of projection is called Orthographic Projection.
For video lecture: www.CrazyProf.in
Page 41
ENGINEERING GRAPHICS (2013-2014) In case of simple object, only two orthographic views are required to show the length, breadth and height of the object. But in some cases, it becomes essential to show three orthographic projections of the object to give complete information needed for the construction of an object.
For video lecture: www.CrazyProf.in
Page 42
ENGINEERING GRAPHICS (2013-2014)
QUESTION OF SHEET NO.8 1. Following figure shows the pictorial view of a block. Draw to a full size scale, the following views in first angle projection: a. Front View (Elevation) seen from ‘A’ b. Side View seen from ‘B’ c. Top View (Plan) seen from ‘C’
2. Following figure shows the pictorial view of a block. Draw to a full size scale, the following views in first angle projection:
a. Elevation from ‘F’; b. Side View & c. Plan.
For video lecture: www.CrazyProf.in
Page 43
ENGINEERING GRAPHICS (2013-2014) 3. Following figure shows the pictorial view of a block. Draw to a full size scale, the following views in first angle projection:
a. Elevation from ‘F’; b. Side View & c. Plan. 4. Following figure shows the pictorial view of a block. Draw to a full size scale, the following views in first angle projection:
a. Elevation from ‘F’; b. Side View & c. Plan.
For video lecture: www.CrazyProf.in
Page 44
ENGINEERING GRAPHICS (2013-2014)
SHEET NO.: 9 QUESTION ON ORTHOGRAPHIC PROJECTION – 2 1. Draw orthographic projection (free hand) of all the wooden blocks (No. of blocks 10).
For video lecture: www.CrazyProf.in
Page 45
ENGINEERING GRAPHICS (2013-2014)
SHEET NO.: 10 ISOMETRIC PROJECTION ISOMETRIC VIEW The three dimensional view or projection of an object obtained on a plane of projection in which all the projectors are parallel but inclined at an angle of 30° to the plane of projection is known as Isometric View. In this type of projection, the object is placed in such a way that all the three axes make equal angle with the plane of projection. It is easier to draw all the edges as compared with oblique or perspective projections.
THEORY OF ISOMETRIC VIEW It is important to know how an isometric view is obtained on the plane of projection. Consider a cube. Let the three corners of the cube meeting at the forward corner is equally inclined to the plane of projection so that the projection to be obtained should give equal length. Therefore, any line so inclined is known as isometric line and the projection thus obtained, represent isometric projection or view. As three edges meeting at a point are equally inclined to each other, hence, the angle between two adjacent edges is equal to 360/3 = 120o. The following figure 14.1 shows the isometric view of a cube in which the edges are parallel to the three main axes. All the edge of the cube areshortend equally. The squrefacues look as rhombuses. The rhombus AOBD as shown in fig. 14.1.The sumeter projection of the top squre fall of the cube in which AB is thetrue length of the diagonal. A squre ANBM is construted is the true length of BD. It is seen from the figure 14.1 that when a line is inclined to the plane of projection, it does notgive the exact size. It is very essential to know the proportion by which various edges of the cube areshortened. This can be found by means of a scale known as isometric scale.
For video lecture: www.CrazyProf.in
Page 46
ENGINEERING GRAPHICS (2013-2014)
DIFFERENT POSITIONS OF ISOMETRIC AXES To show the different sides of the object, the object is revolved about its three isometric axes as shown in the following figure:
DIFFERENCE BETWEEN ISOMETRIC PROJECTION AND ISOMETRIC VIEW: The Isometric Projection means to draw always the Isometric sketch by using Isometric scale and the
For video lecture: www.CrazyProf.in
Page 47
ENGINEERING GRAPHICS (2013-2014) Isometric scale must also be drawn along with the Isometric Projection. Isometric View means to draw Isometric sketch not necessarily taking measurements from the Isometric scale and the Isometric scale may or may not be drawn along with the Isometric view. In this case, measurements can be taken directly from the true orthographic projections because there is little difference between the isometric lengths and true length. Notes: (i) Always draw the Isometric Scale when it is mentioned in the question paper that draw the isometric projections. (ii) In case of Isometric View, Isometric Scale may or may not be drawn. Solution by both the methods is correct.
For video lecture: www.CrazyProf.in
Page 48
ENGINEERING GRAPHICS (2013-2014)
QUESTION OFSHEET NO.10 1. Draw an isometric projection of an equilateral triangular prism having base edges of length = 35 mm and height = 50 mm; its end parallel to H.P. and one of rectangular face parallel to V.P. 2. Draw an isometric projection of a triangular pyramid of 30 mm base edges and 50 mm height standing on its base vertically. 3. Draw an isometric view of a frustum of a triangular pyramid having axis vertical, base edges = 30 mm, top edge = 15 mm and height = 40 mm. 4. The following figure shows the side view and front view of a machine block. Draw the isometric view of the block.
5. The following figure shows the side view and front view of a machine block. Draw the isometric view of the block.
For video lecture: www.CrazyProf.in
Page 49
ENGINEERING GRAPHICS (2013-2014)
SHEET NO.:11 SCALES INTRODUCTION Sometimes it is not possible to represent the actual size of the object on the drawing sheet e.g. building, bridge, etc. So actual size of the object is reduced to some proportion in order to accommodate on the drawing sheet. At times, actual size of the object is so small that it becomes essential to increase the actual size to some proportion to give the clear view e.g. parts of small machine, watches, measuring instruments, etc. The proportion by which the actual size is increased or decreased on the drawing is known as scale. SCALE The proportion by which the actual size of the object is increased or decreased on the drawing is known as scale. Scales are flat or triangular made of wood, celluloid, metal, etc. In drawing, standard recommended scales should be used as far as possible. On scales, different divisions represent the corresponding actual distances to some proportion, which give rapidity in marking off distances on the drawing. SIZES OF SCALE The following sizes of the scales are used in Engineering Drawing: (i) Full Size Scale: The scale in which the actual measurements of the objects are drawn to some size on the drawing, is called full size scale. It is written on scale strip as under. 1 : 1 – Drawing made to actual size. (ii) Reduced Scale: The scale in which the actual measurements of the objects are reduced to some proportion, is called reduced scale. The standard reducing proportions are: 1 : 2 – Drawing made to one half of the actual size. 1 : 5 – Drawing made to one fifth of the actual size. 1 : 10 – Drawing made to one tenth of the actual size. (iii) Enlarged Scale: The scale in which the actual measurements of the objects are increased to some proportion, is called enlarged scale. The standard reducing proportions are: 1 : 50 – Drawing made to one fiftieth of the actual size. 2 : 1 – Drawing made to twice the actual size. 5 : 1 – Drawing made to five times the actual size. REPRESENTATIVE FRACTION The ratio of distance on the drawing sheet of an object to the corresponding actual distance of the object is known as Representative Fraction (R.F.).
For video lecture: www.CrazyProf.in
Page 50
ENGINEERING GRAPHICS (2013-2014)
For video lecture: www.CrazyProf.in
Page 51
ENGINEERING GRAPHICS (2013-2014)
QUESTION OF SHEET NO.11 1. To construct a plain scale to show meters and decimeters if one meter is represented by 2.5 cm and scale is long enough to measure up to 6 meters. 2. To construct a plain scale to show meters and decimeters if one 0.4 meter is represented by 1 cm and scale is long enough to measure up to 5 meters. Find R.F. and show a distance of 4 meters and 5 decimeters on the scale. 3. To construct a diagonal scale to show meters, decimeters and centimeters and long enough to measure 6 meters. If 1 meter is represented by 2.5 centimeters, find the R.F. and show on the scale, a distance of 4 meters, 5 decimeters and 6 centimeters 4. To construct a diagonal scale of R.F. = 1/5000 to show single meters and long enough to measure up to 600 meters. On the scale, show a distance of 457 meters
For video lecture: www.CrazyProf.in
Page 52
MAHARAJA AGRASEN INSTITUTE OF TECHNOLOGY ENGINEERING GRAPHICS (2013 (2013-2014) 2014) LAB MANUAL
NAME: - __________________ _______________________________ _____________ ROLL NO: - ________________ ___________________________ ______________ GROUP: - ____________________________ _______________________________ BRANCH: - __________________________ ______________________________ GROUP TEACHER:________________________ For video lecture: www.CrazyProf.in
Page 1
ENGINEERING GRAPHICS (2013-2014)
GENERAL INSTRUCTIONS FOR ENGG. GRAPHICS LAB. (ETME-159) 1) Students are required to draw sheet in the class (lab) itself.
2) 3)
4) 5) 6)
7)
8)
Students can take back their sheets only after final evaluation. On being absent in the lab, the sheet will not be assessed and will be awarded zero (0). Each student should get their sheets checked on the same day, otherwise it will be considered as late work and will be evaluated out of 5 marks. Name & Roll No. should be written in Ink i.e. with PEN. Each student should make at least 11 drawing sheets in the whole semester. 10 marks will be awarded by the faculty concerned on the basis of performance of the student in quiz and 10 marks for internal viva-voice. At the end of the semester, best of 10 sheets shall be considered for final assessment. These 100 marks will be converted into 20 marks. At the time of external examination, all the sheets shall be submitted to the faculty concerned as below: a. All the sheets should be properly arranged in the serial order. b. All the sheets should be rolled together in a Plastic Sheet Holder.
For video lecture: www.CrazyProf.in
Page 2
ENGINEERING GRAPHICS (2013-2014) SYLLABUS Paper Code: ETME-159 Paper: Engineering Graphics Lab
L 0
P 2
C 1
UNIT - I General: Importance, Significance and scope of engineering drawing, Lettering, Dimensioning, Scales, Sense of proportioning, Different types of projections, Orthographic Projection, B.I.S. Specifications, Projections of Point and Lines: Introduction of planes of projection, Reference and auxiliary planes, projections of points and Lines in different quadrants, traces, inclinations, and true lengths of the lines, projections on Auxiliary planes, shortest distance, intersecting and nonintersecting lines.
UNIT - II Planes other than the Reference Planes: Introduction of other planes (perpendicular and oblique), their traces, inclinations etc., Projections of points and lines lying in the planes, conversion of oblique plane into auxiliary Plane and solution of related problems. Projections of Plane Figures: Different cases of plane figures (of different shapes) making different angles with one or both reference planes and lines lying in the plane figures making different given angles (with one of both reference planes). Obtaining true shape of the plane figure by projection.
UNIT - III Projection of Solids: Simple cases when solid is placed in different positions, Axis faces and lines lying in the faces of the solid making given angles. CADD
UNIT - IV Isometric Projection Nomography : Basic Concepts and use.
TEXT BOOKS: 1. Engineering drawing by N.D.Bhatt (Charotar Publications). 2. Engineering Graphics by Roop Lal & Ramakant Rana (Acme Learning Publications).
REFERENCE BOOKS: 1. Engineering Drawing by Venugopalan. 2. Engineering Drawing by P.S.Gill
For video lecture: www.CrazyProf.in
Page 3
ENGINEERING GRAPHICS (2013-2014)
SHEET NO.: 1 INTRODUCTION Introduction: Technical drawing is the language of engineers. It is graphical language which is universally accepted and used. Without the knowledge of engineering drawing, an engineer is unable to communicate his ideas and eventually would not have been able to construct the various magnificient structures or design intricate machinery. Therefore anyone connected in anyway with engineering construction, must understand this language of engineers. Technical drawing is therefore indispensable today and shall continue to be as long as engineering and technology continue to be part of human activities. The subject engineering graphics will help the students in many ways from drawing images images, describing the shape, size, finish, colour and finally constructing any object. Student will learn the basic concept of orthographic projection, projection of points, lines, planes, solids, section of solids, and development of surfaces of solids and Isometric projections. To express their ideas. This understanding will also help them in interpreting the expressions of others. Engineering Drawing is a universal graphic language of the engineers. It is used by them to develop and record their ideas and transmit them to others for execution. Every language has its own rules of grammar. Engineering Drawing also has its grammar in the theory of projection, its punctuation in the types of lines, its abbreviation’s, symbols & descriptions in the constructions. NEED & SCOPE OF ENGINEERING GRAPHICS: Engineering drawing offers students an insight into the methods to tackle engineering problems. It teaches us the principle of accuracy, exactness & positiveness with regards to the information necessary for the production of the engineering components. It develops the engineering imagination i.e. so essential for creation of successful design. Drawing Sheet: There are different qualities of papers available in the market. Quality of paper to be used depends upon the nature of drawing. The drawing sheet should be uniform in thickness, of such a quality that the erasing marks are not visible and the ink should not spread out. One side of the drawing sheet is rough and other side is smooth. Smooth side is used for drawing work. Sizes of Drawing Sheet: Standard sizes of trimmed and untrimmed sheets according to BIS are given in the table no.1.1:
For video lecture: www.CrazyProf.in
Page 4
ENGINEERING GRAPHICS (2013-2014)
For video lecture: www.CrazyProf.in
Page 5
ENGINEERING GRAPHICS (2013-2014) Layout of drawing Sheet: Given specification are to be followed before commencing the sheet work.
Note Note: all dimensions are in mm
Lists of drawing instruments: instruments:The following set of drawing instruments and materials are required in the preparation of engineering drawing sheet. 1. Drawing board (provided) 2. Drawing sheet(A-2 Size) 3. Mini Drafter 4. Instrument box containing com and dividers 5. Set squares 6. Drawing pin or clips or cello tape (30°-60°, 45°-45°) 7. Protractor 8. Drawing pencils (HB, H, 2H) 9. Eraser, Sharpener, Scale, 10. Plastic Sheet Holder. Circle Master, Dusting Cloth. Convention of lines: For video lecture: www.CrazyProf.in
Page 6
ENGINEERING GRAPHICS (2013-2014)
Arrow Head:
For video lecture: www.CrazyProf.in
Page 7
ENGINEERING GRAPHICS (2013-2014) It is used as terminator on dimension lines. The points of the arrow heads on leader lines and dimension lines must make the with the feature object line or extension line which represents the feature being dimensioned. The standard size ratio for all arrow heads on mechanical drawings is 3:1 (Length to Width).
Figure1.2: Dimensioning
For video lecture: www.CrazyProf.in
Page 8
ENGINEERING GRAPHICS (2013-2014) Dimensioning: 1. Dimensions should be placed outside the views, except when they are cleaner more easily readable inside. 2. Dimension lines should not cross each other 3. As far as possible, dimension should not be shown between the dotted lines. 4. Dimension lines should be placed at about 6mm from the outlines. 5. Head should be pointed and filled in. they are made in ratio 3 to1 (Length) Lettering: - Writing titles, dimension, notes and other important particulars on a drawing is called lettering should therefore be done properly in clear, legible and uniform style preferably freehand and speedily. Types of letters:1. Single stoke letters:- in these letters, the thickness o line of the letter should be such as is obtained in one stoke of the pencil Single stoke letters of two types:(1) Vertical (2) Inclined Inclined letters lean to the right at angle of with the horizontal. The ratio of height to width various but in case of most of the letters it is 7:4. These are shown in following figure Gothic letters: - if stems of single stroke letters, are given more thickness, the letters are known as gothic letters.
For video lecture: www.CrazyProf.in
Page 9
ENGINEERING GRAPHICS (2013-2014)
QUESTION OF SHEET NO.1 1. Write alphabets in capital and numerals in single stroke with 7:4 ratio only (Without Using Scale). 2. Draw the Conventional of lines with there description. 3. Draw the Figure No.1.2 with proper dimensioning as per rules.
For video lecture: www.CrazyProf.in
Page 10
ENGINEERING GRAPHICS (2013-2014)
Sheet No.: 2 PROJECTION OF POINTS Projection: If straight lines are drawn from various points on the contour of an object, to meet a plane of projection, the object is said to be projected on that plane. The figure formed by ing, in correct sequence. The he points at which these lines meet the plane of projection, is called projection of the object. The line from the object to the plane of projection is called project projectors as shown in following figure:
Figure 2.1: Projection Orthographic Projection Projection:: When projectors are parallel to each other and also perpendicular to the plane of projection the projection is called Orthographic projection. The necessary condition for orthographic projections is that the observer should be at infinite distance w.r.t. object. For video lecture: www.CrazyProf.in
Page 11
ENGINEERING GRAPHICS (2013-2014) Planes of Projection: Two planes used for the orthographic projection are called reference planes or principal plane of projection. They intersect each other at right angles. They are known as:(i) Vertical Plane (VP) (ii) Horizontal Plane (HP) The vertical plane is often called the frontal plane and denoted by the letters F.P. Projection on vertical plane (VP) is called front view or elevation. Projection on the HP is called the top view or the plan. The line of intersection of vertical plane and Horizontal Plane is called reference line and is denoted by letter XY. Profile Plane: A plane perpendicular to HP and VP is called profile plane. Projection on profile plane is called side view or end view. Four Quadrants: When the planes of projection are extended beyond the line of intersection, they form four quadrants or dihedral angles. They are numbered as first, second, third and fourth quadrant. The object may be situated on any one of the quadrants. The position of the object relative to planes is described as above or below HP in front of or behind the VP. The planes of projections are assumed to be transparent. The projections are obtained by drawing projectors from the object to the planes (VP and HP) by looking from the front or from the above. The quadrants are shown in figure 2.2.
For video lecture: www.CrazyProf.in
Page 12
ENGINEERING GRAPHICS (2013-2014)
Figure 2.2 2.2: The four Quadrants When the object lies in the first quadrant; it means it may lie: • Above HP and in front of VP • Or on HP and in front of VP • Or on VP and above HP When the object lies in the second quadrant, it means it may be: • Above HP and behind VP • Or on HP and behind VP • Or above HP and on VP When the object lies in the third quadrant, it means it may be: • Below HP and behind VP • On HP and behind VP • Below HP and on VP When object lies in the fourth quadrant, it means it ma mayy be: • Below HP and front of VP • On HP and in front of VP • Below HP and on VP
For video lecture: www.CrazyProf.in
Page 13
ENGINEERING GRAPHICS (2013-2014)
Figure 2.3:: Front View (Elevation) & Top View (Plan) First Angle Projection:: (i) The object lies between observer and plane of projection. (ii) In this method, when views are drawn in their relative position, the top view comes below the front view. In other words, the view seen from above is placed on other side (i.e. below) the front view. (iii) Similarly left hand and view is drawn on the right side of front view and right hand side view is drawn on the left of front view. Convention of first angle projection:
Third Angle Projection: (i) Plane of Projection is lies between object and observer. (ii) In this method, when views are drawn in their relative position, the top comes above the front view. In other words, the view
For video lecture: www.CrazyProf.in
Page 14
ENGINEERING GRAPHICS (2013-2014)
(iii)
seen from above is placed on the same side (i.e. above) of front view. Left hand end view is drawn at left hand of front view and right hand end view is drawn at the right side of front view.
Convention of third angle projection
Note: Students are required to draw on drawing sheets in 1st Angle Projection. ode of practice for general engineering Drawing, As per Indian code published ed in 1973, the committee responsible for preparation has left the option of selecting first or third angle projection method to s. Projection of points in different quadrants 1. Point A is h mm above HP and g mm in front of VP. Point A is in first quadrant.
2. Point B is in the h mm above HP and g mm behind VP. Hence B in the second quadrant.
For video lecture: www.CrazyProf.in
Page 15
ENGINEERING GRAPHICS (2013-2014)
To draw a projection i.e. front view b’ and top view b on the paper, once the third quadrant is open, HP coincide with VP and both HP & VP are above the XY line. 3. Point C is h mm below HP and g mm behind VP. Hence point C in the third quadrant.
To draw the projections (c’ and c) on the paper, once the third quadrant is open, HP lies above XY line and VP below the XY line and draw top view above the XY line and front view below the XY line. 4. Point D is h mm below HP and g mm in front of VP. Hence point D is in the fourth quadrant. To draw projections (Front view d’ and top view d), once the 1st quadrant is opened, HP concedes with VP and both will be below the XY line. Hence front view and top view will be below the XY line.
For video lecture: www.CrazyProf.in
Page 16
ENGINEERING GRAPHICS (2013-2014)
Note: (i) (ii)
Distance of the point above the HP or below the HP indicate the position of front view. Distance of the point in front of VP or behind VP indicate the position of top view.
For video lecture: www.CrazyProf.in
Page 17
ENGINEERING GRAPHICS (2013-2014)
QUESTION OF SHEET NO.2 1.
Draw the projections of the following points taking common reference line, keeping the distance between any two consecutive points as 20mm. (i) Point A 35 mm in front of VP and 35 mm above HP. (ii) Point B is in HP and 30 mm in front of VP (iii) Point C is 30 mm above HP and 45 mm behind VP. (iv) Point D is in VP and 45 mm above HP. (v) Point E is 35 mm below HP and 55 mm behind VP (vi) Point F is in VP and 45 mm below HP. (vii) Point G is both HP and the VP.
2.
A point P is 15 mm above HP and 20 mm infront of VP. Another part Q is 25 mm behind the VP and 40 mm below HP. Draw the projections of P and Q, keeping the distance between their projectors 75 mm, draw straight lines ing their (i) top views (ii) Front views.
3.
Two point A and B are in HP. Point A is 30 mm infront of VP, while B is behind the VP. The distance between their projectors 75 mm and line ing their top views makes an angle of 45° with XY. Find the distance of the point B from the VP.
4.
A point P is 25 mm below HP and its shortest distance form XY(reference line) is 50mm. the point P lies in the third quadrant. Draw its projection.
For video lecture: www.CrazyProf.in
Page 18
ENGINEERING GRAPHICS (2013-2014)
SHEET NO.:3 PROJECTION OF STRAIGHT LINES-I A straight line is the shortest distance between the two points. Hence projection of straight line may be drawn by ing the respective position of its ends, which are points. The position of straight line is described with reference two reference planes. It may be 1. Parallel to HP and VP. 2. Perpendicular to HP and parallel to VP or perpendicular to VP and parallel to HP. 3. Inclined to HP and parallel to VP or Inclined to VP and parallel to HP. 4. Inclined to HP and VP.
I. A line AB is parallel to HP and VP Since line AB is parallel to HP and VP. Its front view a`b` and top view ab will show true length of line AB and will be parallel to XY line
II. A line AB is perpendicular HP and parallel to VP Since a line is perpendicular to HP. It will be automatically parallel to VP since it is parallel to VP, front view will show true length of line AB and top view will be a point, where points a & b will meet.
For video lecture: www.CrazyProf.in
Page 19
ENGINEERING GRAPHICS (2013-2014) III. A line AB is perpendicular to VP and parallel to HP. Since the line AB is parallel to HP. Top view will show true length of line AB and will be perpendicular to any line. Front view will be point, where both points a and b will meet.
IV. A line AB is Inclined to HP and parallel to VP. Since the line AB is parallel to VP. From view will show true length of line and true inclination with HP so knowing the position of point A (as given in question) projection of end A are drawn. From the point A, line a`b` is drawn equal to length of line AB at an angle Ɵ with HP since the line AB is parallel to VP, top view ab will be parallel to XY.
A line AB included to VP and parallel to HP. Since the line AB is parallel to HP. Top view ab will show true length of line AB and true inclination with VP (ɸ). Projection of points A as per given in the question drawn as a’ and a. Draw line ab as top view at angle ɸ with VP. Front view a`b` will be parallel to xy line. V.
For video lecture: www.CrazyProf.in
Page 20
ENGINEERING GRAPHICS (2013-2014)
QUESTION OFSHEET NO.3 1. Straight line AB 40 mm long makes an angle of 30 to the HP. The end A is 10 mm above the HP and 15 mm infront of the VP. Draw the top view and front view of the line AB. 2. Straight line AB 60 mm long makes an angle of 55 to the VP and 25 to the HP. The end A is 10 mm above the HP and 10 mm infront of the VP. Draw the projections of the line AB. 3. Straight line AB 60 mm long makes an angle of 55 to the VP and 25 to the HP. The one end of the straight line AB lies in the HP and is 20 mm infront of the VP. Draw the projections of the line AB. 4. A straight line AB is 50 mm long. Its one end A is 40 mm from the H.P. and 10 mm from V.P. and other end B is 30 mm from the V.P. and 20 mm from the H.P. Draw the projections.
For video lecture: www.CrazyProf.in
Page 21
ENGINEERING GRAPHICS (2013-2014)
Sheet No.:4 PROJECTION OF STRAIGHT LINES-II A given line may be inclined to both the reference planes i.e. HP and VP. In such cases, length of line and its inclination with HP and VP may be given; it may be required to draw its projections. In another case, projections of line may be given, and it may required to determine its true length and its inclinations with HP an VP. I Case:
Length of line AB and its inclination and with HP and with VP are given. Position of point A is also given. Projections are to be drawn.
a’b’1 = Front view of Line AB ab1 = Top view of Line AB Procedure: - Draw the front view a’ and top view a of the point A as per given question:- From a’ draw line a’b’ equal to true length of line AB and at angle Ɵ with the HP. - From the point a, draw a line ab equal true length of line AB and at angle ɸ with VP. For video lecture: www.CrazyProf.in
Page 22
ENGINEERING GRAPHICS (2013-2014) - Draw locus ef, rs, pq and cd from the b’,a’, a and b respectively, parallel to XY line. For example ef is locus of point b’. - If a’b’ is true length of line AB a’b’2 projected length of a’b’ and is equal to length of top view of line AB. - Further project the point b’2 on locuslinepq such that a’b2 = ab2 = length of top view. - Now bring the point b2 on the locus of point b i.e. line cd. Take a as centre and radius equal to ab2, draw arc b2b1. a to b1. ab1 is the length of top view. - Similarly of ab is true length of line AB, ab3 = a`b`3 = length of front view. - Take a’ as centre and radius equal to a`b`3, and draw arc b3’b1’ to bring point b3’ on locus of point b’ i.e. ef a’ to b’1 Hence ab3 = a’b3’ = a’b’1 = length of front view. Note: Point b1 and b1’ projections of point b should lie on the same vertical line. II Case:
Determination true length of a line and its inclination with HP and VP when projections are given.
Front view a’b’ and top view ab of line AB are given. Determine true length of line AB and inclination Ɵ with HP and ɸ with VP. Problem can be solved by two method. (i) Method of rotation. (ii) Trapezoid Method.
METHOD OF ROTATION Principle: Now if front view a’b’ is made parallel to XY, the line AB becomes parallel to HP and its projection ab1 on HP shows its true length and true inclination with VP. For video lecture: www.CrazyProf.in
Page 23
ENGINEERING GRAPHICS (2013-2014) Similarly if top view ab of line AB is made parallel to VP, the line AB becomes parallel to VP and its projection on VP show its true length and true inclination with HP
Procedure: Draw locus of point b’,a’, a and b i.e. lines ef, rs, pq and cd respectively parallel to XY. Take a’ as centre and radius equl to a’b’ and draw arc b’b2’ to make front view a’b’ parallel to XY and line AB becomes parallel to HP. Project point b2’ on the locus of point b. a to b1. ab1 is true length of line AB and show true inclination ɸ with VP. Similarly take a as centre and radius equal to ab, draw an arc bb2, to make top view ab parallel to XY. Now line AB becomes parallel to VP and its projection on VP shows its true length and true angle of inclination with HP.
TRAPEZOID METHOD Procedure: Draw the projections i.e. front view and top view of line AB as per question. A the point a’ draw perpendicular a’A’ equal to distance of point A from XY. Further draw perpendicular b’B1 equal to distance of b from XY line. A1 to B1. A1B1 shows true length of line AB. Line A1B1 and a’b’ will make angle ɸ, inclination with VP if extended back. For video lecture: www.CrazyProf.in
Page 24
ENGINEERING GRAPHICS (2013-2014)
Similarly draw perpendicular aA2 at a equal to distance to distance of a’ from XY. Further draw perpendicular bB2 at b equal distance of b’ from XY A2 to B2. A2B2 shows the true length of line Ab. Line ab and A2B2 will make angle Ɵ, inclination with HP if extended back. Traces of a Line: When a line is inclined to a plane, it will meet that plane produced if necessary. The point of intersection of line and plane is called trace. Horizontal Trace (HT): If a line is inclined to HP, it will meet Horizontal plane then the point of intersection of line and HP is called horizontal trace (HT). Vertical Trace (VT): If a line inclined to VP; it will meet the vertical plane. The point of intersection of line (produced back if necessary) with the VP plane is called vertical trace. Note 1: If a line is inclined to HP and VP. A will have both HT and VT. Note 2: If a line is parallel to any reference plane it will have not trace with that plane.
For video lecture: www.CrazyProf.in
Page 25
ENGINEERING GRAPHICS (2013-2014) Determining Traces of A Line: (1) A line AB is inclined to HP and parallel to VP Draw the front view a’b’ and top view ab of line. Angle of inclination Ɵ with HP is shown by front view. Produced back front view a’b’ till it intersect XY line at point C. From C draw perpendicular on top view ab (produced back) at a point called HT.
(2) A line AB is inclined to VP and parallel to HP Draw the projections (Front view a’b’ and top view ab) of line ABM Angle of inclination ɸ with VP is shown by its top view. Produce back top view ab till it cuts the XY line at D. From D draw perpendicular on the extended front view a’b’. Point of intersection of front view and perpendicular from D is the vertical trace.
For video lecture: www.CrazyProf.in
Page 26
ENGINEERING GRAPHICS (2013-2014) (3)
A line AB is inclined to HP and VP:
Draw the projections (front view a’b’ and top view ab) of line AB. Produce back front view a’b’ till it cut the XY line at C. From C draw perpendicular on extended top view to get HT. Produce back top view ab. It cuts the XY line at D. From D draw perpendicular on the extended front view to get VT.
For video lecture: www.CrazyProf.in
Page 27
ENGINEERING GRAPHICS (2013-2014)
QUESTION OF SHEET NO. 4 PROJECTIONS OF LINES – II 1. A line AB, 65mm long, has its end A 20mm above HP and 25 in front of VP. The end B is 50mm above HP and 65 mm in front of VP. Draw the projections of line AB and show its inclination with HP & VP (Rotational Method). 2. A line AB has its end A 7 mm behind VP and 18mm below HP. The end B 38mm behind VP and 49mm below HP. The distance between the end projectors is 37mm. Draw the projection of line and find out , ∅, HT, VT & TL (Rotational Method). 3. The distance between the projectors of a line is 40 mm. The end A is 20 mm away from HP and 30 mm away from VP & the end B is 50 mm away from HP and 10 mm away from VP. Draw the projection of line AB and determine its , ∅, HT, VT & TL (Trapezoid Method). 4. The end A of line AB is in the HP and 25mm behind VP. The end B is in the VP and 50mm above the HP. The distance between the projectors is 75mm. Draw the projections of line AB, and determine its true length, traces, inclination with HP & VP (Trapezoid Method).
For video lecture: www.CrazyProf.in
Page 28
ENGINEERING GRAPHICS (2013-2014)
SHEET NO.: 5 PROJECTION OF PLANES Plane Surfaces: Plane surfaces have only two dimensions i.e. length and breadth. They do not have thickness. A plane surface may have triangular, rectangular, square, pentagonal or hexagonal shape. Types of Planes: Plain may be divided in two main types:(i) Perpendicular planes (ii) Oblique planes Perpendicular planes can be sub divided into following sub types: (a) Perpendicular to both the reference planes (b) Perpendicular to one reference plane and parallel to other (c) Perpendicular to one reference plane and inclined to other Oblique Planes: Planes which are inclined to both the reference planes are called oblique planes. Traces of Planes: If a plane is perpendicular or inclined to a reference plane, the line in which plane surface meet with reference plane is the trace of plane. The line in which, the plane meet the HP, is called Horizontal Trace (HT). The line in which it meets with VP is called vertical trace (VT). Perpendicular Planes: (i) A square plane is perpendicular to HP and VP: Projection are shown in fig. 5.1
For video lecture: www.CrazyProf.in
Page 29
ENGINEERING GRAPHICS (2013-2014)
Figure 5.1 (ii) A square plane perpendicular to HP and parallel to VP. Since the plane is parallel to VP front view a’b’c’d’ will show its true shape and top view will be a straight line parallel to XY as shown in fig. 5.2
Figure 5.2 Since the plane is perpendicular to HP, it has HT and no VT, since it is parallel to VP. (iii) A square plane perpendicular to VP and parallel to HP. Since the plane is parallel to HP, top view abcd will show its shape but no HT. Front view will be straight line parallel to XY and it also represent VT as in fig. 5.3
For video lecture: www.CrazyProf.in
Page 30
ENGINEERING GRAPHICS (2013-2014)
Figure 5.3 (iv) A square plane perpendicular to HP and inclined to VP. First assume, the plane is parallel to VO. Draw front view a’b’c’d’ first and project top view from the front view. In the second stage, rotate top view ad-bc at angle ɸ, inclination with VP. New top view will be ad – b1c1 Project points b1c1 to get point b’1 and c’1 in the front view to get final front view a’b’1c’1d’.
Figure 5.4
For video lecture: www.CrazyProf.in
Page 31
ENGINEERING GRAPHICS (2013-2014) (v) A square plane perpendicular to VP and inclined to HP First assume parallel to HP and perpendicular to VP top view abcd will show the true shape of square plane. Project front view a’d’-b’c’ from top view.
Figure 5.5 In the second stage rotate front view a’d’ –b’c’ by an angle Ɵ, inclination with HP to get new front view a’d’-b’1c’1. Project the point b’1c’1 on top view to get point b1 and c1 and to get new top view ab1c1d. (vi) Oblique Planes: The projection of planes, inclined to both the reference planes is drawn in three stages as per the conditions given in the question.
For video lecture: www.CrazyProf.in
Page 32
ENGINEERING GRAPHICS (2013-2014)
QUESTION OF SHEET NO.5 1.
A regular pentagon of 25 mm side has one of its side in the HP. Its plane is inclined at 450 to HP and perpendicular to VP. Draw its projections.
2.
To project the front view and top view of a hexagon ABCDEF of 25 mm side with its base on or above H.P. and inclined to V.P. at 600.
3.
A circular plate (ABCDEFGH) of diameter 80 mm is 15 mm above HP such that it makes an angle 300 to the HP. The top view of diameter DH makes an angle of 600 with VP. Draw the projections.
4.
A square ABCD of 50 mm side has its corner A on the HP. Its diagonal AC is inclined at 300 to HP and its diagonal BD is inclined at 450 to VP and parallel to HP. Draw its projections.
For video lecture: www.CrazyProf.in
Page 33
ENGINEERING GRAPHICS (2013-2014)
SHEET NO.: 6 PROJECTION OF SOLIDS A solid has three dimensions, viz. length, breadth and thickness. To represent a solid on flat surface having only length and breadth, at least two orthographic views are necessary. Sometimes, additional views is projected on Auxiliary planes, if necessary to make the description of a solid complete. Solids may be divided into two main groups:(i) Polyhedra (ii) Solids of revolutions
Polyhedra: Polyhedra are defined as solid bounded by planes called faces. When all the faces are equal and regular, the polyhedron is said to be regular. There are five regular 34olyhedral which may defined as stated below:(i) Tetrahedron: It has four equal faces, each one is equilateral triangle. (ii) Cube or hexahedron: It has six faces, each face is square. (iii) Octahedron: It has eight faces. Each face is an equilateral triangle. (iv) Dodecahedron: It has twelve equal faces and each face is regular pentagon. (v) Icosahedrons: It has twenty faces. Each face is an equilateral triangle.
Prism: Prism is a polyhedron having two equal and similar faces called its ends or bases, parallel to each other and ed by other faces, which are parallelograms. The imaginary line ing the centre of the bases is called axis. A right regular prism its axis perpendicular to the bases. The bases may be triangular, square, pentagonal or hexagonal in shape.
For video lecture: www.CrazyProf.in
Page 34
ENGINEERING GRAPHICS (2013-2014) Accordingly they called as triangular, square, pentagonal hexagonal prism.
Pyramid: Pyramid is a polyhedron having a plane figure as base and number of triangular faces meting at a point called the vertex or apex. The imaginary line ing the apex with the centre of base is its axis. A right and regular pyramid has its axis perpendicular to base which is a regular plane figure. Its faces are equal isosedes triangle. As per shape of the base, they are called as Triangular, square, pentagonal and hexagonal pyramid. TRIANGULAR PYRAMID
For video lecture: www.CrazyProf.in
SQUARE PYRAMID
PENTAGONALPYRAMID
Page 35
ENGINEERING GRAPHICS (2013-2014) SOLID OF REVOLUTIONS: A right circular cylinder is a solid generated by the revolution of a rectangle about one of its sides which remain fixed. It has two circular bases. The ing the center of the bases is the axis. It is perpendicular to the bases. A right circular cone is a solid generated by the revolution of a right angled triangle about one of its perpendicular sides which is fixed. It has one circular base. Its axis the apex with the centre of the base to which it is perpendicular. Straight lines drawn from the apex to the circumference of the base circle are all equal and are called generators of the cone. The length of generator is the slant height of the cone.
CYLINDER
CONE SPHERE Figure 6.1: SOLIDS
A sphere is a solid generated by the revolution of a semicircle about its diameter as the axis. The midpoint of diameter is the centre of sphere.
Frustum of a solid: When a pyramid or a cone is cut by a plane parallel to its base, thus removing the top portion, the remaining portion is called its frustum.
Truncated Solid: When a solid is cut by a plane inclined to the base, it said to be truncated. A solid may be inclined to one or both the reference planes. Accordingly projections are drawn in two and three stages respectively.
For video lecture: www.CrazyProf.in
Page 36
ENGINEERING GRAPHICS (2013-2014)
QUESTION OF SHEET NO.6 1.
Draw the projections of a pentagonal prism, base 25 mm side and 50 mm long, resting on one of its rectangular faces on HP with its axis inclined at 45˚ to VP.
2.
Draw the projections of a cylinder 75 mm diameter 100 mm long, lying on the HP with its axis inclined 30˚ to VP and parallel to HP.
3.
A hexagonal pyramid, base 25 mm side and axis 50 mm long, has an edge of its base on the HP. Its axis is inclined at 30˚ to HP and parallel to VP. Draw the projections.
4.
Draw the projections of a cone, base 75 mm diameter and axis 100 mm long, lying on the HP on one of its generator, with the axis parallel to VP.
5.
Draw the projection of cone, base 50 mm diameter and axis 55 long, when it is resting on the HP on its base circle with the axis making an angle of 30˚ with HP and its top view making 45˚ with the VP.
For video lecture: www.CrazyProf.in
Page 37
ENGINEERING GRAPHICS (2013-2014)
SHEET NO.: 7 SECTION OF SOLIDS In the projected views of an object, invisible features are shown by dotted lines. But when such features are too many, these lines make the view more complicated and difficult to interpret. In such cases, it is customary to imagine the object as being cut through or sectioned by planes. This imaginary plane is called the sectioned plane or the cutting plane. The part of the object between cutting plane and observer is assumed to be remove and the view is than shown in sections The projection of the section along with remaining portion of the object is called sectional view. The surface produced by cutting the object by the section plane is called the section. It is indicated by thin section line uniformly spaced and inclined at 45o. Section planes:- section planes or cutting planes are generally perpendicular planes. They may be perpendicular to one of the reference planes and either perpendicular parallel or inclined to other reference plane. They are usually described by their traces. It is important to note that projection of the section plane, on the plane to which it is perpendicular, is a straight line, this line will be parallel, perpendicular or inclined to XY, depending upon the section plane being parallel, perpendicular, or inclined respectively to other reference plane. This straight line coincides with the trace of section plane. True shape of the section:The projection of the section on a reference plane, parallel to the section plane, will show the true shape of the section. Thus when, section plane is parallel to HP, the true shape of the section will be seen in sectional top view. When it is parallel to VP, the true shape will be visible in the sectional front view. But when the section plane is inclined the section has to be projected on an auxiliary plane, parallel to the section plane, to get the true For video lecture: www.CrazyProf.in
Page 38
ENGINEERING GRAPHICS (2013-2014) shape. When the section plane is perpendicular to both the reference planes, the sectional side view will show the true shape of the section.
Table 7.1: Conventions of Materials
For video lecture: www.CrazyProf.in
Page 39
ENGINEERING GRAPHICS (2013-2014)
QUESTION OF SHEET NO.7 1) A right regular pentagonal pyramid side of base 40 mm and ht. 60 mm rest on its base in HP with one of its base edge perpendicular to VP. A section plane parallel to the HP cuts the axis of the pyramid at a distance of 25 mm from its base draw its front view and sectional top view. 2) A right regular pentagonal prism, base edge 40 mm and ht. 70mm is held on HP one of its base edge such that its axis is parallel to the VP and inclined to HP at 30o. An auxiliary horizontal plane cuts the prism, intersecting its axis at a distance of 17 mm from its top end. Draw its front view and sectional top view. 3) A right regular pentagonal pyramid, side of base 40mm and ht. 70mm, rest on its base on HP, such that one its base edges perpendicular to the VP. A section plane parallel to VP cuts the pyramid and is at a distance of 8mm from the axis. Draw its top view and sectional front view. 4) A right circular cone diameter of base 60mm and ht. 70mm, rest on its base on HP. A section planes perpendicular to VP and inclined to HP at 45o, cuts the cone meeting its axis at the distance 36mm from its base. Draw its front view, sectional top view and true shape of section.
For video lecture: www.CrazyProf.in
Page 40
ENGINEERING GRAPHICS (2013-2014)
SHEET NO.: 8 ORTHOGRAPHIC PROJECTION - 1 PROJECTIONS AND PROJECTION LINES (PROJECTORS): When different straight lines are drawn from various points on the contour of the object on to the plane of drawing sheet, the figure obtained on the sheet by ing different points in the correct order is known as Projection of that object (Refer the Following Figure 8.1). And the lines drawn from various points on thecontour of the object on to the plane of drawing sheet are called Projectors or Projection Lines.
Figure 8.1: Projection and projection lines ORTHOGRAPHIC PROJECTION: The image of the object obtained on the plane of projection when the projectors are from the various points on the object, parallel to each other and perpendicular to the plane of projection, then the image obtained on the plane of projection is called Orthographic Projection.
For video lecture: www.CrazyProf.in
Page 41
ENGINEERING GRAPHICS (2013-2014) In case of simple object, only two orthographic views are required to show the length, breadth and height of the object. But in some cases, it becomes essential to show three orthographic projections of the object to give complete information needed for the construction of an object.
For video lecture: www.CrazyProf.in
Page 42
ENGINEERING GRAPHICS (2013-2014)
QUESTION OF SHEET NO.8 1. Following figure shows the pictorial view of a block. Draw to a full size scale, the following views in first angle projection: a. Front View (Elevation) seen from ‘A’ b. Side View seen from ‘B’ c. Top View (Plan) seen from ‘C’
2. Following figure shows the pictorial view of a block. Draw to a full size scale, the following views in first angle projection:
a. Elevation from ‘F’; b. Side View & c. Plan.
For video lecture: www.CrazyProf.in
Page 43
ENGINEERING GRAPHICS (2013-2014) 3. Following figure shows the pictorial view of a block. Draw to a full size scale, the following views in first angle projection:
a. Elevation from ‘F’; b. Side View & c. Plan. 4. Following figure shows the pictorial view of a block. Draw to a full size scale, the following views in first angle projection:
a. Elevation from ‘F’; b. Side View & c. Plan.
For video lecture: www.CrazyProf.in
Page 44
ENGINEERING GRAPHICS (2013-2014)
SHEET NO.: 9 QUESTION ON ORTHOGRAPHIC PROJECTION – 2 1. Draw orthographic projection (free hand) of all the wooden blocks (No. of blocks 10).
For video lecture: www.CrazyProf.in
Page 45
ENGINEERING GRAPHICS (2013-2014)
SHEET NO.: 10 ISOMETRIC PROJECTION ISOMETRIC VIEW The three dimensional view or projection of an object obtained on a plane of projection in which all the projectors are parallel but inclined at an angle of 30° to the plane of projection is known as Isometric View. In this type of projection, the object is placed in such a way that all the three axes make equal angle with the plane of projection. It is easier to draw all the edges as compared with oblique or perspective projections.
THEORY OF ISOMETRIC VIEW It is important to know how an isometric view is obtained on the plane of projection. Consider a cube. Let the three corners of the cube meeting at the forward corner is equally inclined to the plane of projection so that the projection to be obtained should give equal length. Therefore, any line so inclined is known as isometric line and the projection thus obtained, represent isometric projection or view. As three edges meeting at a point are equally inclined to each other, hence, the angle between two adjacent edges is equal to 360/3 = 120o. The following figure 14.1 shows the isometric view of a cube in which the edges are parallel to the three main axes. All the edge of the cube areshortend equally. The squrefacues look as rhombuses. The rhombus AOBD as shown in fig. 14.1.The sumeter projection of the top squre fall of the cube in which AB is thetrue length of the diagonal. A squre ANBM is construted is the true length of BD. It is seen from the figure 14.1 that when a line is inclined to the plane of projection, it does notgive the exact size. It is very essential to know the proportion by which various edges of the cube areshortened. This can be found by means of a scale known as isometric scale.
For video lecture: www.CrazyProf.in
Page 46
ENGINEERING GRAPHICS (2013-2014)
DIFFERENT POSITIONS OF ISOMETRIC AXES To show the different sides of the object, the object is revolved about its three isometric axes as shown in the following figure:
DIFFERENCE BETWEEN ISOMETRIC PROJECTION AND ISOMETRIC VIEW: The Isometric Projection means to draw always the Isometric sketch by using Isometric scale and the
For video lecture: www.CrazyProf.in
Page 47
ENGINEERING GRAPHICS (2013-2014) Isometric scale must also be drawn along with the Isometric Projection. Isometric View means to draw Isometric sketch not necessarily taking measurements from the Isometric scale and the Isometric scale may or may not be drawn along with the Isometric view. In this case, measurements can be taken directly from the true orthographic projections because there is little difference between the isometric lengths and true length. Notes: (i) Always draw the Isometric Scale when it is mentioned in the question paper that draw the isometric projections. (ii) In case of Isometric View, Isometric Scale may or may not be drawn. Solution by both the methods is correct.
For video lecture: www.CrazyProf.in
Page 48
ENGINEERING GRAPHICS (2013-2014)
QUESTION OFSHEET NO.10 1. Draw an isometric projection of an equilateral triangular prism having base edges of length = 35 mm and height = 50 mm; its end parallel to H.P. and one of rectangular face parallel to V.P. 2. Draw an isometric projection of a triangular pyramid of 30 mm base edges and 50 mm height standing on its base vertically. 3. Draw an isometric view of a frustum of a triangular pyramid having axis vertical, base edges = 30 mm, top edge = 15 mm and height = 40 mm. 4. The following figure shows the side view and front view of a machine block. Draw the isometric view of the block.
5. The following figure shows the side view and front view of a machine block. Draw the isometric view of the block.
For video lecture: www.CrazyProf.in
Page 49
ENGINEERING GRAPHICS (2013-2014)
SHEET NO.:11 SCALES INTRODUCTION Sometimes it is not possible to represent the actual size of the object on the drawing sheet e.g. building, bridge, etc. So actual size of the object is reduced to some proportion in order to accommodate on the drawing sheet. At times, actual size of the object is so small that it becomes essential to increase the actual size to some proportion to give the clear view e.g. parts of small machine, watches, measuring instruments, etc. The proportion by which the actual size is increased or decreased on the drawing is known as scale. SCALE The proportion by which the actual size of the object is increased or decreased on the drawing is known as scale. Scales are flat or triangular made of wood, celluloid, metal, etc. In drawing, standard recommended scales should be used as far as possible. On scales, different divisions represent the corresponding actual distances to some proportion, which give rapidity in marking off distances on the drawing. SIZES OF SCALE The following sizes of the scales are used in Engineering Drawing: (i) Full Size Scale: The scale in which the actual measurements of the objects are drawn to some size on the drawing, is called full size scale. It is written on scale strip as under. 1 : 1 – Drawing made to actual size. (ii) Reduced Scale: The scale in which the actual measurements of the objects are reduced to some proportion, is called reduced scale. The standard reducing proportions are: 1 : 2 – Drawing made to one half of the actual size. 1 : 5 – Drawing made to one fifth of the actual size. 1 : 10 – Drawing made to one tenth of the actual size. (iii) Enlarged Scale: The scale in which the actual measurements of the objects are increased to some proportion, is called enlarged scale. The standard reducing proportions are: 1 : 50 – Drawing made to one fiftieth of the actual size. 2 : 1 – Drawing made to twice the actual size. 5 : 1 – Drawing made to five times the actual size. REPRESENTATIVE FRACTION The ratio of distance on the drawing sheet of an object to the corresponding actual distance of the object is known as Representative Fraction (R.F.).
For video lecture: www.CrazyProf.in
Page 50
ENGINEERING GRAPHICS (2013-2014)
For video lecture: www.CrazyProf.in
Page 51
ENGINEERING GRAPHICS (2013-2014)
QUESTION OF SHEET NO.11 1. To construct a plain scale to show meters and decimeters if one meter is represented by 2.5 cm and scale is long enough to measure up to 6 meters. 2. To construct a plain scale to show meters and decimeters if one 0.4 meter is represented by 1 cm and scale is long enough to measure up to 5 meters. Find R.F. and show a distance of 4 meters and 5 decimeters on the scale. 3. To construct a diagonal scale to show meters, decimeters and centimeters and long enough to measure 6 meters. If 1 meter is represented by 2.5 centimeters, find the R.F. and show on the scale, a distance of 4 meters, 5 decimeters and 6 centimeters 4. To construct a diagonal scale of R.F. = 1/5000 to show single meters and long enough to measure up to 600 meters. On the scale, show a distance of 457 meters
For video lecture: www.CrazyProf.in
Page 52
Related Documents 3m3m1z
Engineering Drawing Lab Manual 223v53
October 2021 0
Engineering Drawing 2b3w2g
November 2019 125
Engineering Drawing/ Engineering Lettering 2a1w1a
November 2019 122
Transportation Engineering Lab Manual 115l1u
October 2019 54
Engineering Graphics Lab Manual 6x4c3
December 2019 63
Engineering Mechanics Lab Manual 4c7310
November 2019 2,588More Documents from "RAMAKANT RANA" 5bg3g
5 Friction Applications 1e86q
December 2019 54
Syllabus For First Year And Remaining For Mechanical Branch By Ip University 62346h
December 2019 41
Engineering Graphics Lab Manual 6x4c3
December 2019 63
3 Friction Equilibrium Of The Body On Ladder 604827
November 2019 75
Mcq 4p4hz
January 2021 0