Gas Turbines Operation, Maintenance And Troubleshooting v5jy

QTPC - AN ISO 9001:2008 Regd.

QATAR TECHNICAL PETROLEUM CENTER Gas Turbines: Operation, Maintenance and Troubleshooting Course Duration

: 5 Days Training

Daily Schedule

: 7:30am - 3:30pm

Training Date

: Upon Request

Training Venue

: Doha

Traning Fees

: TBI

Course Outline Day 1

Day 2

• Introduction to Gas Turbines • Gas Turbine Terminology (Power Output, Heat Rate, Efficiency) • Gas Turbine Manufacturers: Siemens, GE, Alstom etc • Types and Applications of Gas Turbines: Heavy Duty, Aero-derivative, Generator Drive, Compressor Drive, Simple Cycle, Combined Cycle • Fundamental Thermodynamics of Gas Turbines: Thermodynamic cycles • Gas turbine performance calculations

Day 3

2

• Gas Turbine Components • Major Accessory Components of a Gas Turbine: Compressor, Combustor, Turbine. • Accessory Components of a Gas Turbine: Load Gearbox, Accessory Gear Box, Generator, Compressor, Bearing and Seals

Day 4

• Gas Turbine Systems: Fuels and Fuel Supply Systems (Gas, Liquid), Lube Oil System, Hydraulic Oil System, Starting Systems, Cooling and Sealing system, Control System and Instrumentation, DLN/DLE and WLN systems and components • Gas Turbine Operating Philosophies • Gas Turbine Operation: Startup, Shutdown and Normal operation, Recording Operational Data

• Routine Inspections and Inspection Scheduling • Gas Turbine Inspection and monitoring • NDT Techniques as applied to gas tubine. • Inspection of Bearings/Seals and Journals and Alignment Checks. • Gas Turbine Maintenance Approaches: Preventive, predictive and corrective.

Day 5 • Gas Turbine Commissioning • Root cause analysis • Introduction to Machinery Troubleshooting • Gas Turbine Troubleshooting • General Discussion and Case Studies.

QATAR TECHNICAL PETROLEUM CENTER, P.O. Box 9955, Salwa Road, Doha, Qatar. Tel: +974 4458 1440. Fax: +974 4458 0414 Email: [email protected] URL: www.qtpc.qa

QTPC - AN ISO 9001:2008 Regd.

QATAR TECHNICAL PETROLEUM CENTER Gas Turbines: Operation, Maintenance and Troubleshooting

Course Overview This course presents both the fundamental basics and up to date technology for the operation and maintenance of gas turbines. For turbines to operate efficiently, they require good load control, efficient safety devices, and proper maintenance program. The course presents an overview of gas turbines, fundamentals of thermodynamics, mechanical equipment standards, and gas turbine components. The course also covers bearings and seals, fuels and fuel supply systems, control system, and instrumentation. Gas turbine operation and maintenance and troubleshooting will be also presented. By the end of the course the participants will be updated with the up-to-date technology for the operation, maintenance, and troubleshooting of gas turbines.

Course Objectives By the end of the course the participants will be able to • Identify and learn about technology and relative merits of gas turbine power plants. • Analyze thermodynamically the gas power plant cycles. • Learn and make performance analysis for the gas turbine main components. • Analyze the variables, which affect the performance parameters such as power, efficiency, and heat rate. • Learn about different maintenance activities on gas turbine. • Learn about testing, operation, monitoring, and troubleshooting of gas turbines. • Learn about new technologies gas turbine inspection and monitoring. • Apply troubleshooting techniques to gas turbine.

Who Should Attend? This course is targeted at technicians and engineers involved in operation and maintenance of Gas Turbines. Experienced engineers and maintenance specialists will also benefit from attending this course, as will those managers concerned with the maintenance scheduling and repair aspects of Gas Turbines.

About the Course Instructor Dr. Mohammed Al-Odat, is graduated with PhD from University of Jordan and he is a professor of Mechanical and Process Engineering. He is a highly experienced consultant and trainer with over 20 years experience in various disciplines of process and Mechanical engineering. Currently he is a professor of Mechanical Engineering at Umm Al-Qura University-Saudi Arabia.

He has published over 50 papers on thermo-fluid systems and taught many courses in mechanical and process engineering such as heat transfer, thermodynamics, boilers and steam generation, Power plants, heat exchangers and others at Al-Balqa Applied University, JUST, Yarmouk and Philadelphia universities in Jordan, Yanbu Industrial College and Umm Al-Qura University at Saudi Arabia. With respect to Training courses, he has delivered many technical and management training courses in Gulf Region such as: • Operation Maintenance and Troubleshooting of: Heat Exchangers, Cooling Towers, Steam Boilers, Flare System and Gas Turbine. • Troubleshooting in Chemical Plants. • Corrosion in Petrochemical Industries. • Process Plant shutdown, Start-Up and Commissioning. • Computerized Maintenance Management Systems (CMMS). • Maintenance scheduling and planning.

QATAR TECHNICAL PETROLEUM CENTER, P.O. Box 9955, Salwa Road, Doha, Qatar. Tel: +974 4458 1440. Fax: +974 4458 0414 Email: [email protected] URL: www.qtpc.qa