Halliburton Red Book Sec200 5q1sp

Back to Main Menu

HN00500

HN00501

RTTS™ PACKER AND SSC™ II VALVE

SSC II VALVE

•

Hookwall type retrievable packer designed for testing, treating, and squeezing.

•

Full-opening, ball-type, subsurface control valve.

•

•

Optional integral circulating valve may be opened and locked at any time to allow circulation above the packer.

Can be installed without left-hand rotation eliminating the problems inherent when unscrewing pipe ts.

•

•

Designed to hold pressure from either direction.

Ball valve automatically closes to shut in the well when the SSC II is set down.

•

Ideal for performing multiple operations on one or more zones with only one trip in the well.

•

•

Large mandrel ID allows pumping large volumes of fluid with minimum pressure drop.

Ball valve is opened by picking up and can be reclosed by setting back down if high pressure is detected below the valve.

•

Only right-hand rotation is required to release the workstring from the valve.

•

Rotation is not required to reattach the workstring to the valve.

•

Can be used to test the blowout preventers during drilling.

•

Large ID also allows age of tubing-type perforating guns.

•

Sizes available to run in all standard casing sizes from 23/8-in. through 20-in. O.D.

Dimensions and Strengths

RTTS PACKER

Dimensions and Strengths

HN00502

CHAMP® PACKERS

HN00503

CHAMP PACKER •

Hookwall-type retrievable packer with a concentric by.

•

Design helps eliminate problems associated with accidently opening a conventional by during circulation around the bottom of the packer.

•

Excellent for use in highly deviated wells or where pipe manipulation is difficult.

•

By can be opened by picking straight up (no torque required).

•

Easy to relocate in multiple zones with only one trip in the well for treating, testing, or squeezing.

CHAMP L/L PACKER •

Liner-lock feature allows the Champ packer to be locked in the running position until it lands on the appropriate liner.

•

Excellent for use in highly deviated wells with deep liners.

Page 1

SECTION NO. 200 DIMENSIONS and STRENGTHS

Copyright © 1995, 2001 HaIliburton Company ALL RIGHTS RESERVED

Page 2 TABLE

DIMENSIONS AND STRENGTHS OF NON-UPSET Size O.D. In.

Grade

Wt. per Ft. With Coupings, Lb. NonUpset

Upset

Integral t

Inside Diameter In.

Drift Diameter In.

1.050

C-75 C-90 F-25* H-40 J-55 L-80 N-80 N-80† T-95

1.14 1.14 — 1.14 1.14 1.14 1.14 1.14 1.14

1.20 1.20 1.20 1.20 1.20 1.20 1.20 1.20 1.20

1.20 — — — 1.20 — 1.20 — —

.824 .824 .824 .824 .824 .824 .824 .824 .824

.730 .730 .730 .730 .730 .730 .730 .730 .730

1.315

C-75 C-75* F-25* H-40 J-55 J-55* L-80 LS-65 N-80 N-80* P-105* T-95

1.70 — — 1.70 1.70 — 1.70 1.70 1.70 — — 1.70

1.80 — 1.80 1.80 1.80 — 1.80 1.80 1.80 — — 1.80

1.72 2.25 — 1.72 1.72 2.25 — — 1.72 2.25 2.25 —

1.049 .957 1.049 1.049 1.049 .957 1.049 1.049 1.049 .957 .957 1.049

.955 .848 .955 .955 .955 .848 .955 .955 .955 .848 .848 .955

1.660

C-75 C-75* C-90 F-25* H-40 H-40 J-55 J-55 J-55* L-80 LS-65† N-80 N-80* P-105* T-95

2.30 — 2.30 — — 2.30 — 2.30 — 2.30 2.30 2.30 — — 2.30

2.40 — 2.40 2.40 — 2.40 — 2.40 — 2.40 2.40 2.40 — — 2.40

2.33 3.02 — — 2.10 2.33 2.10 2.33 3.02 — — 2.33 3.02 3.02 —

1.380 1.278 1.380 1.380 1.410 1.380 1.410 1.380 1.278 1.380 1.380 1.380 1.278 1.278 1.380

1.286 1.184 1.286 1.286 1.286 1.286 1.286 1.286 1.184 1.286 1.286 1.286 1.184 1.184 1.286

1.900

C-75 C-75* C-90 F-25* H-40 H-40 J-55 J-55 J-55*

2.75 — 2.75 2.75 — 2.75 — 2.75 —

2.90 — 2.90 2.90 — 2.90 — 2.90 —

2.76 3.64 — — 2.40 2.76 2.40 2.76 3.64

1.610 1.500 1.610 1.610 1.650 1.610 1.650 1.610 1.500

1.516 1.406 1.516 1.516 1.516 1.516 1.516 1.516 1.406

*Non API Standard. Shown for information only. †Lone Star Pipe Data

Page 3 NO. 201

EXTERNAL UPSET & INTEGRAL T TUBING Threaded & Coupled O.D. O.D. of lg., In. of NonUpset Upset Upset In.

Integral t Box O.D. In.

** Collapse Resist. psi

** Internal Yield Pressure psi

t Yield Strength, Lb.*** Threaded & Coupled

NonUpset

Upset

Integral t

1.313 — — 1.313 1.313 — 1.313 — —

1.660 — 1.660 1.660 1.660 — 1.660 — —

1.315 — 1.315 1.315 1.315 — 1.315 — —

1.327 — — — 1.327 — 1.327 — —

14,410 17,290 5,960 7,680 10,560 15,370 15,370 15,370 18,250

14,120 16,950 4,710 7,530 10,360 15,070 15,070 15,070 17,890

11,920 14,300 8,320 6,360 8,740 12,720 12,710 12,720 15,100

24,950 29,900 — 13,310 18,290 26,600 26,610 26,600 31,600

25,000 — — — 18,000 — 27,000 — —

1.660 — — 1.660 1.660 — — — 1.660 — — —

1.900 — 1.900 1.900 1.900 — — — 1.900 — — —

1.469 — 1.469 1.469 1.469 — — — 1.469 — — —

1.550 1.600 — 1.550 1.550 1.600 — — 1.550 1.600 1.600 —

13,640 17,640 5,540 7,270 10,000 12,940 14,550 11,820 14,550 18,820 24,700 17,270

13,270 17,870 4,430 7,080 9,730 13,100 14,160 11,500 14,160 19,060 25,010 16,810

20,540 — — 10,960 15,060 — 21,910 17,800 21,910 — — 26,020

37,040 — 12,350 19,760 27,160 — 39,500 32,100 39,510 — — 46,900

29,940 48,000 — 15,970 21,960 35,000 — — 31,940 51,000 67,000 —

2.054 — — — — 2.054 — 2.054 — — — 2.054 — — —

2.200 — — 2.200 — 2.200 — 2.200 — — — 2.200 — — —

1.812 — — 1.812 — 1.812 — 1.812 — — — 1.812 — — —

1.880 1.927 — — 1.880 1.880 1.880 1.880 1.927 — — 1.880 1.927 1.927 —

11,580 15,270 13,900 4,440 5,570 6,180 7,660 8,490 11,200 12,360 10,040 12,360 16,290 21,380 14,670

11,070 15,100 13,80 3,690 5,270 5,900 7,250 8,120 11,070 11,810 9,590 11,810 16,110 21,140 14,020

29,120 — 34,900 — — 15,530 — 21,360 — 31,060 25,240 31,060 — — 36,900

50,140 — 60,200 16,710 — 26,740 — 36,770 — 53,500 43,500 53,480 — — 63,500

41,600 66,000 — — 22,180 22,180 30,500 30,500 48,000 — — 44,370 71,000 93,000 —

2.200 — — 2.200 — 2.200 — 2.200 —

2.500 — — 2.500 — 2.500 — 2.500 —

2.094 — — 2.094 — 2.094 — 2.094 —

2.110 2.162 — — 2.110 2.110 2.110 2.110 2.162

10,570 14,130 12,620 3,920 4,920 5,640 6,640 7,750 10,360

10,020 13,820 12020 3,340 4,610 5,340 6,330 7,350 10,130

35,800 — 43000 11,930 — 19,090 — 26,250 —

59,960 — 72000 19,990 — 31,980 — 43,970 —

50,420 80,000 — — 26,890 26,890 36,970 36,970 57,000

** Collapse, Internal Yield Strengths are minimum values with no safety factor, reproduced by permission from API Bul. 5C2, Bulletin on Performance Properties of Casing and Tubing.

Page 4 TABLE


Grade

Wt. per Ft. With Coupings, Lb.

Inside Diameter In.

Drift Diameter In.

— — 2.76 3.64 3.64 —

1.610 1.610 1.610 1.500 1.500 1.610

1.516 1.516 1.516 1.406 1.406 1.516

— 3.25 — — 3.25 3.25 — 3.25 3.25

3.25 — 3.25 3.25 — — 3.25 — —

1.751 1.751 1.751 1.751 1.751 1.751 1.751 1.751 1.751

1.657 1.657 1.657 1.657 1.657 1.657 1.657 1.657 1.657

— 4.70 5.95 —

— 4.70 5.95 5.30 6.20 7.70 — — — — — — — — 4.70 5.30 6.20 7.70 — — — — — 4.70 5.95 5.30 6.20 7.70 4.70 5.95 5.30

2.041 1.995 1.867 1.939 1.853 1.703 2.041 1.995 1.867 2.041 1.995 2.041 1.995 2.041 1.995 1.939 1.853 1.703 2.041 1.995 1.867 1.995 2.041 1.995 1.867 1.939 1.853 1.703 1.995 1.867 1.939

1.947 1.901 1.773 1.845 1.759 1.609 1.947 1.901 1.773 1.947 1.901 1.947 1.901 1.947 1.901 1.845 1.759 1.609 1.947 1.901 1.773 1.901 1.947 1.901 1.773 1.845 1.759 1.609 1.901 1.773 1.845

NonUpset

Upset

L-80 LS-65† N-80 N-80* P-105* T-95

2.75 2.75 2.75 — — 2.75

2.90 2.90 2.90 — — 2.90

2.063

C-75 C-90 H-40 J-55 L-80 LS-65† N-80 P-110 T-95

— — — — — — — — —

2.375

C-75 C-75 C-75 C-75* C-75* C-75* C-90 C-90 C-90 F-25* F-25* H-40 H-40 J-55 J-55 J-55* J-55* J-55* L-80 L-80† L-80† LS-66† N-80 N-80 N-80 N-80* N-80* N-80* P-105 P-105 P-105*

4.00 4.60 5.80 — — — 4.00 4.60 5.80 4.00 4.60 4.00 4.60 4.00 4.60 — — — 4.00 4.60 5.80 4.60 4.00 4.60 5.80 — — — 4.60 5.80 —

— — 4.70 5.95 — 4.70 — 4.70 — 4.70 — — — — 4.70 5.95 4.70 — 4.70 5.95 — — — 4.70 5.95 —


Integral t

Page 5 NO. 201






Integral t

NonUpset

Upset

64000 — 52000 — 63,960 53,780 — 84,000 — 110,000 75900 —

— — 2.200 — — —

— — 2.500 — — —

— — 2.094 — — —

— — 2.110 2.162 2.162 —

11,280 9,160 11,280 15,070 19,780 13,440

10680 8680 10,680 14,740 19,340 12690

38200 31000 38,180 — — 45300

— — — — — — — — —

— — — — — — — — —

— — — — — — — — —

2.325 — 2.325 2.325 — — 2.325 — —

10,480 12,420 5,590 7,690 11,180 9,090 11,180 15,680 13,240

9,920 11,910 5,290 7,280 10,590 8,600 10,590 14,560 12,570

— — — — — — — — —

— 80,240 — — 71,400 57,900 — 98,100 84,700

2.875 2.875 2.875 — — — — — — 2.875 2.875 2.875 2.875 2.875 2.875 — — — — — — — 2.875 2.875 2.875 — — — 2.875 12.875 —

— 3.063 3.063 — — — — — — — 3.063 — 3.063 — 3.063 — — — — — — — — 3.063 3.063 — — — 3.063 3.063 —

— 2.594 2.594 — — — — — — — 2.594 — 2.594 — 2.594 — — — — — — — — 2.594 2.594 — — — 2.594 2.594 —

— 2.700 2.906 2.740 2.937 3.125 — — — — — — — — 2.700 2.740 2.937 3.125 — — — — — 2.700 2.906 2.740 2.937 3.125 2.700 2.906 2.740

9,520 11,040 14,330 12,510 14,670 18,220 10,940 13,250 17,190 3,530 4,160 5,230 5,890 7,190 8,100 9,170 10,760 13,360 9,980 11,780 15,280 9,570 9,980 11,780 15,280 13,340 15,650 19,430 15,460 20,060 17,510

9,230 10,500 14,040 12,050 14,420 18,570 11,070 12,600 16,840 3,080 3,500 4,920 5,600 6,770 7,700 8,840 10,580 13,620 9,840 11,200 14,970 9,100 9,840 11,200 14,970 12,860 15,390 19,810 14,700 19,650 16,870

56,500 67,430 96,560 — — — 67,800 80,900 115,900 18,830 22,480 30,130 35,960 41,430 49,450 — — — 60,300 71,900 103,000 58,400 60,260 71,930 102,990 — —

— 97,820 126,940 — — — — 117,400 152,300 — 32,600 — 52,170 — 71,730 — — — — 104,300 135,400 84,800 — 104,340 135,400 — —

66,910 — 35,690 49,070 — — 71,370 — —

— 98,000 127,000 111,000 130,000 161,000 — — — — — — — — 72,000 81,000 95,000 118,000 — — — — — 104,000 135,000 118,000 139,000 172,000 94,410 136,940 137,000 135,180 177,710 178,000 155,000


Page 6 TABLE


2.875

Grade


Upset

P-105* P-105* P-110* P-110* T-95 T-95 T-95

— — 4.60 5.80 4.00 4.60 5.80

— — 4.70 5.95 — 4.70 5.95

C-75 C-75 C-75* C-75* C-75* C-75* C-90 C-90 C-90 F-25* H-40 J-55 J-55* J-55* J-55* J-55* J-55* L-80 L-80† L-80† LS-65† N-80 N-80 N-80* N-80* N-80* N-80* P-105 P-105 P-105* P-105* P-105* P-110 P-110 P-110* T-95 T-95 T-95

6.40 8.60 — — — — 6.40 7.80 8.60 6.40 6.40 6.40 — — — — — 6.40 7.80 8.60 6.40 6.40 8.60 — — — — 6.40 8.60 — — — 7.80 8.60 6.40 6.40 7.80 8.60

6.50 8.70 — — — — 6.50 7.90 8.70 6.50 6.50 6.50 — — — — — 6.50 7.90 8.70 6.50 6.50 8.70 — — — — 6.50 8.70 — — — 7.90 8.70 6.50 6.50 7.90 8.70


Inside Diameter In.

Drift Diameter In.

6.20 7.70 — — — — —

1.853 1.703 1.995 1.867 2.041 1.995 1.867

1.759 1.609 1.901 1.773 1.947 1.901 1.773

6.50 8.70 7.90 9.50 10.70 11.00 — — — — — 6.50 7.90 8.70 9.50 10.70 11.00 — — — — 6.50 8.70 7.90 9.50 10.70 11.00 6.50 8.70 7.90 9.50 10.70 — — — — — —

2.441 2.259 2.323 2.195 2.091 2.065 2.441 2.323 2.259 2.441 2.441 2.441 2.323 2.259 2.195 2.091 2.065 2.441 2.323 2.259 2.441 2.441 2.259 2.323 2.195 2.091 2.065 2.441 2.259 2.323 2.195 2.091 2.323 2.259 2.441 2.441 2.323 2.259

2.347 2.165 2.229 2.101 1.997 1.971 2.347 2.229 2.165 2.347 2.347 2.347 2.229 2.165 2.101 1.997 1.971 2.347 2.229 2.165 2.347 2.347 2.165 2.229 2.101 1.997 1.971 2.347 2.165 2.229 2.101 1.997 2.229 2.165 2.347 2.347 2.229 2.165

Integral t

Page 7 NO. 201






NonUpset

Upset

Integral t

— — 2.875 2.875 — — —

— — 3.063 3.063 — — —

— — 2.594 2.594 — — —

2.937 3.125 — — — — —

20,540 25,510 13,800 17,910 11,410 13,980 18,150

20,200 26,010 15,400 20,590 11,690 13,300 17,780

— — 98,900 141,610 71,600 85,400 122,300

— 182,000 — 226,000 143,470 — 186,170 — — — 123,900 — 160,800 —

3.500 3.500 — — — — — — — 3.500 3.500 3.500 — — — — — — — — — 3.500 3.500 — — — — 3.500 3.500 — — — — — 3.500 — — —

3.668 3.668 — — — — — — — 3.668 3.668 3.668 — — — — — — — — — 3.668 3.668 — — — — 3.668 3.668 — — — — — 3.668 — — —

3.094 3.094 — — — — — — — 3.094 3.094 3.094 — — — — — — — — — 3.094 3.094 — — — — 3.094 3.094 — — — — — 3.094 — — —

3.220 3.500 3.437 3.625 3.687 3.750 — — — — — 3.220 3.437 3.500 3.625 3.687 3.750 — — — — 3.220 3.500 3.437 3.625 3.687 3.750 3.220 3.500 3.437 3.625 3.687 — — — — — —

10,470 14,350 13,020 15,640 17,670 18,150 12,380 15,620 17,220 3,870 5,580 7,680 9,550 10,530 11,470 12,960 13,310 11,170 13,890 15,300 9,070 11,160 15,300 13,890 16,690 18,850 19,360 14,010 20,090 18,230 21,900 24,740 19,090 21,040 13,080 12,940 16,490 18,170

9,910 14,060 12,600 15,520 17,890 18,490 11,890 15,120 16,870 3,300 5,280 7,260 9,250 10,320 11,390 13,120 13,570 10,570 13,440 15,000 8,590 10,570 15,000 13,450 16,560 19,090 19,730 13,870 19,690 17,650 21,730 25,050 18,480 20,620 14,530 12,550 15,960 17,810

98,970 149,360 — — — — 118,800 158,500 179,200 32,990 52,780 72,580 — — — — — 105,600 140,900 159,300 85,800 105,570 159,310 — — — — 138,560 209,100 — — — 193,700 219,100 145,160 125,400 167,300 189,200

135,900 186,290 — — — — 163,100 202,800 223,500 45,300 72,480 99,660 — — — — — 145,000 180,300 198700 117,800 144,960 198,710 — — — — 190,260 260,810 — — — 247,900 273,200 199,320 172,100 214,100 236,000

136,000 186,000 169,000 203,000 229,000 236,000 — — — — — 100,000 124,000 137,000 149,000 168,000 173,000 — — — — 145,000 198,000 180,000 217,000 245,000 251,000 190,000 261,000 236,000 285,000 321,000 — — — — — —


Page 8 TABLE


3.500

Grade

C-75 C-75 C-75 C-75 C-75* C-75* C-75* C-90 C-90 C-90 F-25* F-25* F-25* H-40 H-40 H-40 J-55 J-55 J-55 J-55* J-55* J-55* J-55* L-80 L-80 L-80† L-80† LS-65 LS-651 N-80 N-80 N-80 N-80 N-80* N-80* N-80* P-105 P-105 P-105* P-105* P-105* P-105* P-110 P-110* P-110* T-95 T-95 T-95 T-95


Upset

Integral t

7.70 9.20 10.20 12.70 — — — 7.70 9.20 10.20 7.70 9.20 10.20 7.70 9.20 10.20 7.70 9.20 10.20 — — — — 7.70 12.70 9.20 10.20 9.20 10.20 7.70 9.20 10.20 12.70 — — — 9.20 12.70 — — — — 12.70 9.20 12.70 7.70 9.20 10.20 12.70

— 9.30 — 12.95 — — — — 9.30 — — 9.30 — — 9.30 — — 9.30 — — — — — — 12.95 9.30 — 9.30 — — 9.30 — 12.95 — — — 9.30 12.95 — — — — 12.95 9.30 12.95 — 9.30 — 12.95

— 9.30 10.30 12.95 12.80 15.80 16.70 — — — — — — — — — — 9.30 10.30 12.80 12.95 15.80 16.70 — — — — — — — 9.30 10.30 12.95 12.80 15.80 16.70 9.30 12.95 10.30 12.80 15.80 16.70 — — — — — — —


Inside Diameter In.

Drift Diameter In.

3.068 2.992 2.922 2.750 2.764 2.548 2.480 3.068 2.992 2.922 3.068 2.992 2.922 3.068 2.992 2.922 3.068 2.992 2.922 2.764 2.750 2.548 2.480 3.068 2.75 2.992 2.922 2.992 2.922 3.068 2.992 2.922 2.750 2.764 2.548 2.480 2.992 2.750 2.922 2.764 2.548 2.480 2.75 2.992 2.750 3.068 2.992 2.922 2.75

2.943 2.867 2.797 2.625 2.639 2.423 2.355 2.943 2.867 2.797 2.943 2.867 2.797 2.943 2.867 2.797 2.943 2.867 2.797 2.639 2.625 2.423 2.355 2.943 2.625 2.867 2.797 2.867 2.797 2.943 2.867 2.797 2.625 2.639 2.423 2.355 2.867 2.625 2.797 2.639 2.423 2.355 2.625 2.867 2.625 2.943 2.867 2.797 2.625

Page 9 NO. 201


4.250 4.250 4.250 4.250 — — — — — — 4.250 4.250 4.250 4.250 4.250 4.250 4.250 4.250 4.250 — — — — — — — — — — 4.250 4.250 4.250 4.250 — — — 4.250 4.250 — — — — — 4.250 4250 — — — —

— 4.500 — 4.500 — — — — — — — 4.500 — — 4.500 — — 4.500 — — — — — — — — — — —

— 3.750 — 3.750 — — — — — — — 3.750 — — 3.750 — — 3.750 — — — — — — — — — — —

4.500 — 4.500 — — — 4.500 4.500 — — — — — 4.500 4.500 — — — —

3.750 — 3.750 — — — 3.750 3.750 — — — — — 3.750 3.750 — — — —


— 3.905 3.955 4.312 4.312 4.500 4.562 — — — — — — — — — — 3.905 3.955 4.312 4.312 4.500 4.562 — — — — — — — 3.905 3.955 4.312 4.312 4.500 4.562 3.905 4.312 3.955 4.312 4.500 4.562 — — — — — — —



7,540 10,040 11,360 14,350 14,110 17,630 18,670 8,540 11,570 13,640 2,970 3,680 4,330 4,630 5,380 6,060 5,970 7,400 8,330 10,350 10,530 12,950 13,690 7,870 15,310 10,540 12,120 8,750 9,850 7,870 10,530 12,120 15,310 15,060 18,800 19,920 13,050 20,090 15,920 19,760 24,680 26,140 21,050 12,620 17,940 8,850 12,080 14,390 18,180

8,100 9,520 10,840 14,060 13,800 17,850 19,130 9,720 11,430 13,010 2,700 3,180 3,610 4,320 5,080 5,780 5,940 6,980 7,950 10,120 10,230 13,090 14,020 8,640 15,000 10,160 11,560 8,260 9,390 8,640 10,160 11,560 15,000 14,730 19,040 20,400 13,330 19,690 15,180 19,320 24,990 26,770 20,630 13,970 20,630 10,260 12,070 13,730 17,810


NonUpset

Upset

Integral t

122,010 149,140 173,530 230,990 — — — 146,400 179,000 208,200 40,670 49,710 57,840 65,070 79,540 92,550 89,470 109,370 127,250 — — — — 130,100 246,400 159,100 185,100 129,300 150,400 130,140 159,090 185,100 246,390 — — — 208,800 323,390 — — — — 338,800 218,740 338,790 154,500 188,900 219,800 292,600

— 194,260 — 276,120 — — — — 233,100 — — 64,760 — — 103,610 — — 142,460 — — — — — — 294,500 207,200 — 168,400 — — 207,220 — 294,530 — — — 271,970 386560 — — — — 405,000 284,920 365,570 — 246,100 — 349,700

— 194,000 219,000 276,000 272,000 339,000 359,000 — — — — — — — — — — 142,000 160,000 199,000 203,000 249,000 264,000 — — — — — — — 207,000 233,000 295,000 290,000 362,000 383,000 272,000 387,000 306,000 380,000 475,000 503,000 — — — — — — —


Page 10 TABLE


Grade


Upset

Integral t

Inside Diameter In.

Drift Diameter In.

4.000

C-75 C-75 C-75* C-90 C-90 F-25* F-25* H-40 H-40 J-55 J-55 J-55* L-80 L-80 N-80 N-80 N-80* P-105* P-105* T-95 T-95

9.50 — — 9.50 — 9.50 — 9.50 — 9.50 — — 9.50 — 9.50 — — — — 9.50 —

— — 11.00 — 11.00 — 11.00 — 11.00 — 11.00 — — 11.00 — 11.00 — — — — 11.00

— 13.40 11.00 — — — — — — — 11.00 11.60 — — — 11.00 13.40 11.00 13.40 — —

3.548 3.340 3.476 3.548 3.476 3.548 3.476 3.548 3.476 3.548 3.476 3.428 3.548 3.476 3.548 3.476 3.340 3.476 3.340 3.548 3.476

3.423 3.215 3.351 3.423 3.351 3.423 3.351 3.423 3.351 3.423 3.351 3.303 3.423 3.351 3.423 3.351 3.215 3.351 3.215 3.423 3.351

4.500

C-75 C-75* C-75* C-75* C-90 F-25* H-40 J-55 J-55* L-80 N-80 N-80* N-80* N-80* P-105* P-105* P-105* P-105* T-95

12.60 — — — 12.60 12.60 12.60 12.60 — 12.60 12.60 — — — — — — — 12.60

12.75 — — — 12.75 12.75 12.75 12.75 — 12.75 12.75 — — — — — — — 12.75

12.75 13.50 15.50 19.20 — — — 12.75 13.50 — 12.75 13.50 15.50 19.20 12.75 13.50 15.50 19.20 —

3.958 3.920 3.826 3.640 3.958 3.958 3.958 3.958 3.920 3.958 3.958 3.920 3.826 3.640 3.958 3.920 3.826 3.640 3.958

3.833 3.795 3.701 3.515 3.833 3.833 3.833 3.833 3.795 3.833 3.833 3.795 3.701 3.515 3.833 3.795 3.701 3.515 3.833


Page 11 NO. 201






NonUpset

Upset

Integral t

4.750 — — — — 4.750 — 4.750 — 4.750 — — — — 4.750 — — — — — —

— — 5.000 — — — 5.000 — 5.000 — 5.000 — — — — 5.000 — — — — —

— — 4.250 — — — 4.250 — 4.250 — 4.250 — — — — 4.250 — — — — —

— 4.625 4.405 — — — — — — — 4.405 4.000 — — — 4.405 4.625 4.405 4.625 — —

6,350 11,350 8,410 7,080 9,590 2,630 3,220 4,060 4,900 5,110 6,590 7,300 6,590 8,800 6,590 8,800 12,110 10,700 15,900 9,7310 9,980

7,420 10,830 8,600 8,900 10,320 2,470 2,870 3,960 4,590 5,440 6,300 6,880 7,910 9,170 7,910 9,170 11,550 12,040 15,160 9,390 10,90

135,010 — — 162,000 — 45,000 — 72,000 — 99,010 — — 144,000 — 144,010 — — — — 171,000 —

— — 230,760 — 276,900 — 76,920 — 123,070 — 169,220 — — 246,100 — 246,140 — — — — 292,300

— 285,000 231,000 — — — — — — — 169,000 137,000 — — — 246,000 304,000 323,000 400,000 — —

5.200 — — — — 5.200 5.200 5.200 — — 5.200 — — — — — — — —

5.563 — — — — 5.563 5.563 5.563 — — 5.563 — — — — — — — —

4.750 — — — — 4.750 4.750 4.750 — — 4.750 — — — — — — — —

4.910 4.935 5.125 5.312 — — — 4.910 4.935 — 4.910 4.935 5.125 5.312 4.910 4.935 5.125 5.312 —

7,200 8,170 10,390 12,960 8,120 2,870 4,500 5,720 6,420 7,500 7,500 8,540 11,090 13,820 8,950 10,350 13,820 18,140 8,410

7,900 8,460 9,830 12,540 9,490 2,630 4,220 5,800 6,200 8,430 8,430 9,020 10,480 13,380 11,070 11,840 13,760 17,560 10,010

195,680 — — — 234,800 65,230 104,360 143,500 — 208,700 208,730 — — — — — — — 247,900

270,030 — — — 324,000 90,010 144,020 198,030 — 288,000 288,040 — — — — — — — 342,000

270,000 288,000 331,000 412,000 — — — 198,000 211,000 — 288,000 307,000 353,000 439,000 378,000 403,000 463,000 567,000 —


Page 12 TABLE

DIMENSIONS AND STRENGTHS OF API Size O.D. In.

Wt. Per Ft. W/lg. Lb.

I.D. In.

I.D. At. Full Upset In.

Collapse Pressure** D PSI

E PSI

G PSI *

S-135 PSI *

23/8 23/8

4.85 6.65

1.995 1.815

1.437 1.125

*6,850 11,440

11,040 15,600

13,250 18,720

16,560 23,400

27/8 27/8

6.85 10.40

2.441 2.151

1.875 1.187

— 12,110

10,470 16,510

12,560 19,810

15,700 24,760

31/2 31/2 31/2

9.50 13.30 15.50

2.992 2.764 2.602

2.250 1.875 1.750

— 10,350 12,300

10,040 14,110 16,770

12,110 16,940 20,130

15,140 21,170 25,160

4 4

11.85 14.00

3.476 3.340

2.937 2.375

— 8,330

8,410 11,350

10,310 14,630

12,820 17,030

41/2 41/2 41/2

13.75 16.60 20.00

3.958 3.826 3.640

3.156 2.812 2.812

— 7,620 9,510

7,200 10,390 12,960

8,920 12,470 15,560

10,910 15,590 19,450

5 5

16.25 19.50

4.408 4.276

3.750 3.687

— 7,390

6,970 10,000

8,640 12,090

10,550 15,110

51/2 51/2

21.90 24.70

4.778 4.670

3.812 3.500

6,610 7,670

8,440 10,460

10,350 12,560

12,870 15,700

59/16 59/16 59/16

*19.00 *22.20 *25.25

4.975 4.859 4.733

4.125 3.812 3.500

4,580 5,480 6,730

5,640 6,740 8,290

— — —

— — —

65/8 65/8 65/8

*22.20 25.20 *31.90

6.065 5.965 5.761

5.187 5.000 4.625

3,260 4,010 5,020

4,020 4,810 6,170

— 6,160 —

— 6,430 —

**Non API Standard. Shown for information only. **Collapse, Internal Yield and Tensile Strength are minimum values with no safety factor.

Page 13 NO. 202

SEAMLESS INTERNAL UPSET DRILL PIPE Internal Yield Pressure** D PSI

E PSI

G PSI *

Tensile Strength**

S-135 PSI *

D 1000 Lb.

E 1000 Lb.

G 1000 Lb. *

S-135 1000 Lb. *

Size O.D. In.

*7,110 10,500 11,350 15,470

14,700 21,660

18,900 27,850

70 101

98 138

137 194

176 249

23/8 23/8

— 9,910 12,120 16,530

13,870 23,140

17,830 29,750

— 157

136 214

190 300

245 386

27/8 27/8

— 9,520 10,120 13,800 12,350 16840

13,340 19,320 23,570

17,140 24,840 30,310

— 199 237

194 272 323

272 380 452

350 489 581

31/2 31/2 31/2

— 7,940

8,600 10,830

12,040 15,160

15,470 19,500

— 209

231 285

323 400

415 514

4 4

— 7,210 9,200

7,900 9,830 12,540

11,070 13,760 17,560

14,230 17,690 22,580

— 242 302

270 331 412

378 463 577

486 595 742

41/2 41/2 41/2

— 6,970

7,770 9,500

10,880 13,300

13,980 17,100

— 290

328 396

459 554

591 712

5 5

6,320 7,260

8,610 9,900

12,060 13,860

15,500 17,820

321 365

437 497

612 696

787 895

51/2 51/2

5,090 6,090 7,180

6,950 8,300 9,790

— — —

— — —

267 317 369

365 432 503

— — —

— — —

59/16 59/16 59/16

4,160 4,790 6,275

5,530 6,540 8,540

— 9,150 —

— 11,770 —

307 359 463

418 489 631

— 685 —

— 881 —

65/8 65/8 65/8

Page 14 TABLE

DIMENSIONS AND Size O.D. In.

Grade

Extreme Line

Thread & lg.

Wt. Per Ft. With lg., Lb.

Inside Dia. In.

Drift Dia. In.

O.D. of lg. In.

Drift Dia. In.

O.D. of Box In.

** Col’pse Resistance PSI

41/2

C-75 C-75 C-90 C-90 C-95 C-95 F-25* H-40 HCL-80ª HCL-80ª HCL-80ª HCN-80ª HCN-80ª H-110ª J-55 J-55 J-55 K-55 K-55 K-55 L-80 L-80 L-80 LS-140ª LS-65ª LS-65 LS-65ª LS-65 N-80 N-80 P110 P-110 P-110 Q-125ª S-95 S-95 S-95 T-95 T-95 V-150*

11.60 13.50 11.60 13.50 11.60 13.50 9.50 9.50 11.60 13.50 15.10 11.60 13.50 11.60 9.50 10.50 11.60 9.50 10.50 11.60 11.60 13.50 15.10 15.10 9.50 10.50 11.60 13.50 11.60 13.50 11.60 13.50 15.10 15.10 11.60 13.50 15.10 11.60 13.50 15.10

4.000 3.920 4.000 3.920 4.000 3.920 4.090 4.090 4.000 3.920 3.826 4.000 3.920 4.000 4.090 4.052 4.000 4.090 4.052 4.000 4.000 3.920 3.826 3.826 4.090 4.052 4.000 3.920 4.000 3.920 4.000 3.920 3.826 3.826 4.000 3.920 3.826 4.000 3.920 3.826

3.875 3.795 3.875 3.795 3.875 3.795 3.965 3.965 3.875 3.795 3.701 3.875 3.795 3.875 3.965 3.927 3.875 3.965 3.927 3.875 3.875 3.795 3.701 3.701 3.965 3.927 3.875 3.795 3.875 3.795 3.875 3.795 3.701 3.701 3.875 3.795 3.701 3.875 3.795 3.701

5.000 5.000 — — 5.000 5.000 5.000 5.000 — — — — — — 5.000 5.000 5.000 5.000 5.000 5.000 — — — — — — — — 5.000 5.000 5.000 5.000 5.000 — — — — — — 5.000

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

6,130 8,170 6,810 9,300 7,010 9,650 1,920 2,770 8,650 10,380 12,330 8,650 10,380 8,650 3,310 4,010 4,960 3,310 4,010 4,960 6,350 8,540 11,090 17,240 3,600 4,420 5,560 7,300 6,350 8,540 7,560 10,670 14,320 15,840 8,650 10,380 12,330 7,030 9,660 18,110

5

C-75 C-75 C-75* C-75* C-90 C-90 C-90 C-90 C-90 C-95 C-95 C-95* C-95*

15.00 18.00 20.30 23.20 15.00 18.00 21.40 23.20 24.10 15.00 18.00 20.30 23.20

4.408 4.276 4.184 4.044 4.408 4.276 4.126 4.044 4.000 4.408 4.276 4.184 4.044

4.283 4.151 — — 4.233 4.151 4.001 3.919 3.875 4.283 4.151 — —

5.563 5.563 — — — — — — — 5.563 5.563 — —

4.151 4.151 4.059 3.919 — — — — — 4.151 4.151 4.059 3.919

5.360 5.360 5.094 5.094‡ — — — — — 5.360 5.360 5.250 5.094‡

6,970 10,000 11,240 12,970 7,840 11,530 14,360 15,560 16,200 8,090 12,010 14,250 16,430

*Non API Standard. Shown for information only. ªLone Star Pipe Data ** Collapse, Internal Yield and t Yield Strengths are minimum values with no safety actor, reproduced by permission from API Bul. 5C2, Bulletin on Performance Properties of Casing and Tubing.

Page 15 NO. 203

STRENGTHS OF CASING Internal Yield Pressure PSI** Plain End or Ext. Line

Round Thread

** Body Yield Stgth. 1,000 Lbs.

t Strength - 1000 Lbs.** Threaded & lg. t ButRound Thread tress Short Long Thd.

Short

Long

Buttress Thd.

7,290 8,460 8,750 10,150 9,240 10,710 — 3,190 7,780 9,020 10,480 7,780 9,020 10,690 4,380 4,790 5,350 4,380 4,790 5,350 7,780 9,020 10,480 18,350 5,180 5,660 6,320 7,330 7,780 9,020 10,690 12,410 14,420 16,380 9,240 10,710 12,450 9,240 10,710 —

— — — — — — 1,990 3,190 — — — — — — 4,380 4,790 5,350 4,380 4,790 5,350 — — — — 5,180 5,660 6,320 — — — — — — — — — — — — —

7,290 8,460 8,750 10,150 9,240 10,710 — — 7,780 9,020 10,480 7,780 9,020 10,690 — — 5,350 — — 5,350 7,780 9,020 10,480 18,350 — — 6,320 7,330 7,780 90,201 10,690 12,410 14,420 16,380 9,240 10,710 12,450 9,240 10,710 19,660

7,290 8,460 8,750 10,150 9,240 10,710 — — 7,780 9,020 9,790 7,780 9,020 10,690 — 4,790 5,350 — 4,790 5,350 7,780 9,020 10,480 17,140 — 5,660 6,320 7,330 7,780 9,020 10,690 12,410 13,460 15,300 9,240 10,710 11,630 9,240 10,710 18,360

250 288 300 345 317 364 69 111 267 307 353 267 307 367 152 165 184 152 165 184 267 307 353 617 180 195 217 249 267 307 367 422 485 551 317 364 419 317 364 661

— — — — — — 71 77 — — — — — — 101 132 154 112 146 170 — — — — 135 154 179 — — — — — — — — — — — — —

212 257 223 270 234 284 — — 223 270 325 223 270 279 — — 162 — — 180 212 257 308 487 — — 188 228 223 270 279 338 406 438 245 297 357 234 284 519

288 331 309 355 325 374 — — 312 359 408 312 359 385 — 203 225 — 249 277 291 334 384 616 — 231 256 295 304 349 385 443 509 554 338 388 446 325 374 683

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

7,770 9,500 10,710 12,550 9,320 11,400 13,770 15,060 15,750 9,840 12,040 13,560 15,890

7,770 9,500 — — — — — — — — — — —

7,770 9,290 — — 9,320 11,400 12,170 12,170 12,170 9,840 12,040 — —

— — — — 9,320 11,150 11,150 11,150 11,150 9,840 11,770 — —

328 396 — — 394 475 564 611 636 416 501 — —

— — 369† 369† — — — — — — — — —

295 376 — — 311 396 490 540 567 326 416 — —

375 452 — — 404 484 537 537 537 424 512 — —

416 446 529‡‡ 529‡‡ — — — — — 459 493 584‡‡ 584‡‡

† Hydril TS †† Hydril FJ-P

‡ Hydril Super FJ-P ‡‡ Hydril Super EU

Ext. Line t

Page 16 TABLE


5

Thread & lg.

Grade


Inside Dia. In.

C-95ª C-95ª F-25* HCL-80ª HCL-80ª HCL-80ª HCN-80ª HCN-80ª HCN-80ª J-55 J-55 J-55 K-55 K-55 K-55 L-80 L-80 L-80ª L-80ª L-80ª LS-140ª LS-65 LS-65ª LS-65ª LS-65ª N-80 N-80 N-80* N-80* N-80*ª N-80ª P-110 P-110 P-110 P-110* P-110*ª P-110ª Q-125ª Q-125ª Q-125ª Q-125ª S-95ª S-95ª S-95ª T-95 T-95 T-95 T-95 T-95 V-150 V-150* V-150* V-150* V-150*

21.40 24.10 11.50 15.00 18.00 23.20 15.00 18.00 23.20 11.50 13.00 15.00 11.50 13.00 15.00 15.00 24.10 18.00 21.40 23.20 18.00 11.50 13.00 15.00 18.00 15.00 18.00 20.30 23.20 21.40 24.10 15.00 18.00 20.30 23.20 21.40 24.10 18.00 21.40 23.20 24.10 15.00 18.00 23.20 15.00 18.00 21.40 23.20 24.10 24.10 15.00 18.00 20.80 24.20

4.126 4.000 4.560 4.408 4.276 4.044 4.408 4.276 4.044 4.560 4.494 4.408 4.560 4.494 4.408 4.408 4.000 4.276 4.126 4.044 4.276 4.560 4.494 4.408 4.276 4.408 4.276 4.184 4.044 4.126 4.000 4.408 4.276 4.184 4.044 4.126 4.000 4.276 4.126 4.044 4.000 4.408 4.276 4.044 4.408 4.276 4.126 4.044 4.000 4.000 4.408 4.276 4.156 4.000

Drift Dia. In.

4.001 3.875 4.435 4.283 4.151 3.919 4.283 4.151 3.919 4.435 4.369 4.283 4.435 4.369 4.283 4.283 3.875 4.151 4.001 3.919 4.151 4.435 4.369 4.283 4.151 4.283 4.151 — — 4.001 3.875 4.283 4.151 — — 4.001 3.875 4.151 4.001 3.919 3.875 4.283 4.151 3.919 4.283 4.151 4.001 3.919 3.875 3.875 4.283 4.151 4.031 3.875

O.D. of lg. In.

— — 5.563 — — — — — — 5.563 5.563 5.563 5.563 5.563 5.563 — — — — — — — — — — 5.563 5.563 — — — — 5.563 5.563 — — — — — — — — — — — — — — — — — 5.563 5.563 5.563 5.563

Extreme Line Drift Dia. In.

O.D. of Box In.


— — — — — — — — — — — 4.151 — — 4.151 — — — — — — — — — — 4.151 4.151 4.059 3.919 — — 4.151 4.151 4.059 3.919 — — — — — — — — — — — — — — — — — — —

— — — — — — — — — — — 5.360 — — 5.360 — — — — — — — — — — 5.360 5.360 5.250 5.094‡ — — 5.360 5.360 5.094‡ 5.094‡ — — — — — — — — — — — — — — — — — — —

15,160 17,100 1,820 9,380 11,880 15,820 9,380 11,880 15,820 3,060 4,140 5,560 3,060 4,140 5,550 7,250 14,400 10,500 12,760 13,830 16,080 3,290 4,590 6,280 8,730 7,250 10,490 11,990 13,830 12,760 14,400 8,830 13,450 16,490 19,020 17,550 19,800 14,830 19,940 21,620 22,500 9,380 12,030 16,430 8,110 12,030 15,160 16,430 17,100 27,000 10,260 16,860 22,860 27,000


Page 17 NO. 203


14,530 16,630 — 8,290 10,140 13,380 8,290 10,140 13,380 4,240 4,870 5,700 4,240 4,870 5,700 8,290 14,000 10,140 12,240 13,380 17,740 5,010 5,760 6,730 8,240 8,290 10,140 11,420 13,380 12,240 14,000 11,400 13,940 15,710 18,400 16,820 19,250 15,840 19,120 20,910 21,880 9,840 12,040 15,890 9,840 12,040 14,530 15,890 16,630 26,250 — — — —

Round Thread


Short

Long

Buttress Thd.

— — 1,930 — — — — — — 4,240 4,870 5,700 4,240 4,870 5,700 — — — — — — 5,010 5,760 6,730 — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

12,840 12,840 — 8,290 10,140 10,810 8,290 10,140 10,810 — 4,870 5,700 — 4,870 5,700 8,290 10,810 10,140 10,810 10,810 17,740 — 5,760 6,730 8,240 8,290 10,140 — — 10,810 10,810 11,400 13,940 — — 14,870 14,870 15,840 16,900 16,900 16,900 9,840 12,040 12,840 9,840 12,040 12,840 12,840 12,840 20,280 15,540 19,000 20,280 20,280

11,770 11,770 — 8,290 9,910 9,910 8,290 9,910 9,910 — 4,870 5,700 — 4,870 5,700 8,290 9,910 9,910 9,910 9,910 17,340 — 5,760 6,730 8,240 8,290 9,910 — — 9,910 9,910 11,400 13,620 — — 13,620 13,620 15,480 15,480 15,480 15,480 9,840 11,770 11,770 9,840 11,770 11,770 11,770 11,770 18,580 15,540 18,580 18,580 18,580


595 672 83 — 422 543 350 422 543 182 208 241 182 208 241 350 566 422 501 543 738 215 245 284 343 350 422 — — 501 566 481 580 — — 689 778 659 783 849 884 416 501 645 416 501 595 645 672 1,060 656 791 910 1,060


— — 84 — — — — — — 133 169 207 147 186 228 — — — — — — 162 196 240 — — — 388† 388† — — — — 485† 485† — — — — — — — — — — — — — — — — — — —


515 595 — 311 396 540 311 396 540 — 182 223 — 201 246 295 538 377 466 513 594 — 212 259 331 311 396 284†† 284†† 490 558 388 495 354†† 354†† 613 708 535 662 729 765 342 436 594 326 416 515 567 595 907 497 634 755 905

563 563 — 408 492 516 408 492 537 — 252 293 — 309 359 379 510 457 510 510 735 288 334 403 396 477 363‡ 363‡ 537 537 503 606 454‡ 454‡ 671 671 661 724 724 724 441 532 590 424 512 563 563 563 858 685 826 847 847

Ext. Line t

— — — — — — — — — — — 328 — — 416 — — — — — — — — — — 437 469 556‡‡ 556‡‡ — — 547 587 696‡‡ 696‡‡ — — — — — — — — — — — — — — — — — — —

Page 18 TABLE


51/2

Grade

C-75 C-75 C-75 C-75* C-90 C-90 C-90 C-90 C-90 C-90 C-90 C-90 C-90 C-90 C-90 C-95 C-95 C-95 C-95 C-95* F-25* H-40 HCL-80ª HCL-80ª HCL-80ª HCN-80ª HCN-80ª HCN-80ª H-Iloª HCQ-125ª J-55 J-55 J-55 K-55 K-55 K-55 L-80ª L-80ª L-80ª LS-140ª LS-140ª LS-140ª LS-65ª LS-65ª LS-65ª LS-65ª N-80 N-80 N-80 N-80* N-80*ª P-110 P-110 P-110

Thread & lg.


Inside Dia. In.

17.00 20.00 23.00 26.00 17.00 20.00 23.00 26.00 26.80 29.70 32.60 35.30 38.00 40.50 43.10 17.00 20.00 20.00 23.00 26.00 13.00 14.00 17.00 20.00 23.00 17.00 20.00 23.00 17.00 17.00 14.00 15.50 17.00 14.00 15.50 17.00 17.00 20.00 23.00 17.00 20.00 23.00 14.00 15.50 17.00 20.00 17.00 20.00 23.00 26.00 20.00 17.00 20.00 23.00

4.892 4.778 4.670 4.548 4.892 4.778 4.670 4.548 4.500 4.376 4.250 4.126 4.000 3.876 3.750 4.892 4.778 4.778 4.670 4.548 5.044 5.012 4.892 4.778 4.670 4.892 4.778 4.670 4.892 4.892 5.012 4.950 4.892 5.012 4.950 4.892 4.892 4.778 4.670 4.892 4.778 4.670 5.012 4.950 4.892 4.778 4.892 4.778 4.670 4.548 4.778 4.892 4.778 4.670

Drift Dia. In.

4.767 4.653 4.545 — 4.767 4.653 4.545 4.423 4.375 4.251 4.125 4.001 3.875 3.751 3.625 4.767 4.653 4.653 4.545 — 4.919 4.887 4.767 4.653 4.545 4.767 4.653 4.545 4.767 4.767 4.887 4.825 4.767 4.887 4.825 4.767 4.767 4.653 4.545 4.767 4.653 4.545 4.887 4.825 4.767 4.653 4.767 4.653 4.545 — 4.653 4.767 4.653 4.545

O.D. of lg. In.

6.050 6.050 6.050 — — — — — — — — — — — — 6.050 6.050 — 6.050 — 6.050 6.050 — — — — — — — — 6.050 6.050 6.050 6.050 6.050 6.050 — — — — — — — — — — 6.050 6.050 6.050 — — 6.050 6.050 6.050


O.D. of Box In.


4.653 4.653 4.545 4.423 — — — — — — — — — — — 4.653 4.653 — 4.545 4.423 — — — — — — — — — — — 4.653 4.653 — 4.653 4.653 — — — — — — — — — — 4.653 4.653 4.545 4.423 — 4.653 4.653 4.545

5.860 5.860 5.860 5.656 — — — — — — — — — — — 5.860 5.860 — 5.860 5.656‡ — — — — — — — — — — — 5.860 5.860 — 5.860 5.860 — — — — — — — — — — 5.860 5.860 5.860 5.656‡ — 5.860 5.860 5.860

6,070 8,440 10,460 11,860 6,740 9,630 12,380 14,240 14,880 16,510 18,130 19,680 21,200 22,650 24,080 6,930 10,000 10,010 12,920 15,020 1,660 2,630 8,580 10,630 12,450 8,580 10,630 12,450 8,580 8,580 3,120 4,040 4,910 3,120 4,040 4,910 6,290 8,830 11,160 8,580 12,950 17,500 3,360 4,470 5,510 7,540 6,280 8,830 11,160 12,650 8,830 7,460 11,080 14,520


Page 19 NO. 203


7,250 8,610 9,900 11,360 8,710 10,340 11,880 13,630 14,320 16,090 17,900 19,670 21,480 23,250 25,060 9,190 10,910 10,910 12,540 14,390 — 3,110 7,740 9,190 10,560 7,740 9,190 10,560 10,640 12,090 4,270 4,810 5,320 4,270 4,810 5,320 7,740 9,190 10,560 13,540 16,080 18,490 5,050 5,690 6,290 7,470 7,740 9,190 10,560 12,120 9,190 10,640 12,640 14,520

Round Thread Short

Long

Buttress Thd.

— — — — — — — — — — — — — — — — — — — — 1,810 3,110 — — — — — — — — 4,270 4,810 5,320 4,270 4,810 5,320 — — — — — — 5,050 5,690 6,290 — — — — — — — — —

7,250 8,610 9,260 — 8,710 10,340 11,110 11,110 — — — — — — — 9,190 10,910 10,910 11,730 — — — 7,740 9,190 9,880 7,740 9,190 9,880 10,640 12,090 — 4,810 5,320 — 4,810 5,320 7,740 9,190 9,880 13,540 16,080 17,290 — 5,690 6,290 7,470 7,740 9,190 9,880 — 9,190 10,640 12,640 13,580

7,250 8,430 8,430 — 8,710 10,120 10,120 10,120 — — — — — — — 9,190 10,680 10,680 10,680 — — — 7,740 8,990 8,990 7,740 8,990 8,990 10,640 12,090 — 4,810 5,320 — 4,810 5,320 7,740 8,990 8,990 13,540 15,740 15,740 — 5,690 6,290 7,470 7,740 8,990 8,990 — 8,990 10,640 12,360 12,360



372 437 497 — 447 525 597 676 707 785 861 935 1,007 1,076 1,144 471 554 554 630 — 94 161 397 466 530 397 466 530 546 620 222 248 273 222 248 273 397 466 530 695 816 928 262 293 323 379 397 466 530 — 466 546 641 729


— — — 432† — — — — — — — — — — — — — — — — 95 130 — — — — — — — — 172 202 229 189 222 252 — — — — — — 200 235 267 — — — 455† — — — —


327 403 473 — 356 438 514 598 — — — — — — — 374 460 460 540 — — — 356 438 514 356 438 514 445 481 — 217 247 — 239 272 338 416 489 534 657 771 — 253 287 353 348 428 502 315†† 428 445 548 643

423 497 550 — 456 436 579 579 — — — — — — — 480 563 563 608 — — — 462 542 551 462 542 579 568 620 — 300 329 — 366 402 428 503 550 690 810 869 — 342 376 442 446 524 579 451‡ 524 568 667 724

Ext. Line t

471 497 549 678‡‡ — — — — — — — — — — — 521 549 — 606 749‡‡ — — — — — — — — — — — 339 372 — 429 471 — — — — — — — — — — 496 523 577 713‡‡ — 620 654 722

Page 20 TABLE

DIMENSIONS AND Extreme Line

Thread & lg.

Grade


Inside Dia. In.

5½

P-110* P-110ª Q-125ª Q-125ª Q-125ª Q-125ª S-95 S-95ª S-95ª T-95 T-95 T-95 T-95 T-95 T-95 T-95 T-95 T-95 T-95 T-95 V-150 V-150* V-150* V-150*

26.00 20.00 17.00 20.00 23.00 26.00 17.00 20.00 23.00 17.00 20.00 23.00 26.00 26.80 29.70 32.60 35.30 38.00 40.50 43.10 20.00 20.00 23.00 26.00

4.548 4.778 4.892 4.778 4.670 4.548 4.892 4.778 4.670 4.892 4.778 4.670 4.548 4.500 4.376 4.250 4.126 4.000 3.876 3.750 4.778 4.778 4.670 4.548

— 4.653 4.767 4.653 4.545 4.423 4.767 4.653 4.545 4.767 4.653 4.545 4.423 4.375 4.251 4.125 4.001 3.875 3.751 3.625 4.653 4.653 4.545 4.423

55/8

H2S-90ª H2S-95ª HCL-80ª L-80ª P-110ª

26.70 26.70 26.70 26.70 26.70

4.671 4.671 4.671 4.671 4.671

53/4

C-95 C-95ª C-95ª C-95ª J-55ª J-55ª J-55ª L-80ª L-80ª L-80ª L-80ª N-80ª N-80ª N-80ª N-80ª P-110ª P-110ª P-110ª P-110ª

19.70 18.10 21.80 24.20 16.50 18.10 19.70 18.10 19.70 21.80 24.20 18.10 19.70 21.80 24.20 18.10 19.70 21.80 24.20

5.080 5.142 5.000 4.910 5.198 5.142 5.080 5.142 5.080 5.000 4.910 5.142 5.080 5.000 4.910 5.142 5.080 5.000 4.910

Size O.D. In.

Drift Dia. In.

O.D. of Box In.


— — — — — — — — — — — — — — — — — — — — — 6.050 6.050 6.050

4.423 — — — — — — — — — — — — — — — — — — — — — — —

5.656‡ — — — — — — — — — — — — — — — — — — — — — — —

17,390 11,100 7,890 12,080 16,070 19,770 8,580 10,630 12,940 6,940 10,010 12,940 15,030 15,700 17,430 19,140 20,760 22,380 23,920 25,400 13,460 13,480 18,390 23,720

4.544 4.544 4.544 4.544 4.544

— — — — —

— — — — —

— — — — —

14,750 14,750 14,750 12,420 17,080

4.955 5.017 4.875 4.785 5.073 5.017 4.955 5.017 4.955 4.875 4.785 5.017 4.955 4.875 4.785 5.017 4.955 4.875 4.785

— — — — — — — — — — — — — — — — — — —

— — — — — — — — — — — — — — — — — — —

— — — — — — — — — — — — — — — — — — —

7,980 6,380 10,050 12,370 3,720 4,520 5,410 5,700 7,030 8,740 10,650 5,700 7,030 8,740 10,650 6,640 8,530 10,960 13,700

Drift Dia. In.

O.D. of lg. In.


Page 21 NO. 203


Round Thread Short

Long

Buttress Thd.



16,660 12,630 12,090 14,360 16,510 18,930 9,190 10,910 12,540 9,190 10,910 12,540 14,390 15,110 16,990 18,810 20,770 22,670 24,540 26,450 17,230 — — —

— — — — — — — — — — — — — — — — — — — — — — — —

— 12,630 12,090 14,360 15,430 15,430 9,190 10,910 11,730 9,190 10,910 11,730 11,730 — — — — — — — 17,230 17,230 18,520 22,720

— 12,360 12,090 14,050 14,050 14,050 9,190 10,680 10,680 9,190 10,680 10,680 10,680 — — — — — — — 16,860 16,860 16,860 —

— 641 620 729 829 939 471 554 630 471 554 630 714 746 828 909 987 1,063 1,136 1,208 874 874 994 —

569† — — — — — — — — — — — — — — — — — — —

13,360 14,100 11,870 11,870 16,320

— — — — —

11,110 11,730 9,880 9,880 13,580

10,120 10,680 8,990 8,990 12,360

9,690 8,790 10,840 12,140 4,620 5,090 5,610 7,400 8,160 9,130 10,230 7,400 8,160 9,130 10,230 10,180 11,220 12,550 14,060

— — — — — — — — — — — — — — — — — — —

— — — — — — — — — — — — — — — — — — —

9,690 8,790 10,840 12,140 4,620 5,090 5,610 7,400 8,160 9,130 10,230 7,400 8,160 9,130 10,230 10,180 11,220 12,550 14,060


Ext. Line t

— — —

393†† 548 481 592 694 808 392 482 566 374 460 540 628 — — — — — — — 701 701 823 —

564‡ 667 620 728 782 782 498 585 637 480 563 608 608 — — — — — — — 865 908 910 —

892‡‡ — — — — — — — — — — — — — — — — — — — — — — 722‡

694 733 617 617 849

— — — — —

514 539 501 488 642

579 608 550 550 724

— — — — —

541 494 602 668 261 286 313 416 456 507 563 416 456 507 563 572 627 697 774

— — — — — — — — — — — — — — — — — — —

— — — — — — — — — — — — — — — — — — —

550 502 611 679 314 344 377 447 490 545 605 466 511 568 630 594 651 723 803

— — — — — — — — — — — — — — — — — — —


Page 22 TABLE


Grade

Extreme Line

Thread & lg.


Inside Dia. In.

Drift Dia. In.

O.D. of lg. In.

*6

F-25* H-40 J-55 N-80 N-80 N-80 P-110 P-110

15.00 18.00 18.00 18.00 20.00 23.00 23.00 26.00

5.524 5.424 5.424 5.424 5.352 5.240 5.240 5.132

5.399 5.299 5.299 5.299 5.227 5.115 5.115 5.007

6.625 6.625 6.625 6.625 6.625 6.625 6.625 6.625

65/8

C-75 C-75 C-75 C-90 C-90 C-90 C-95 C-95 C-95 F-25* H-40 J-55 J-55 K-55 K-55 L-80ª L-80ª L-80ª LS-65 LS-65 LS-65ª N-80 N-80 N-80 P-110 P-110 P-110 Q-125ª

24.00 28.00 32.00 24.00 28.00 32.00 24.00 28.00 32.00 17.00 20.00 20.00 24.00 20.00 24.00 24.00 28.00 32.00 24.00 28.00 20.00 24.00 28.00 32.00 24.00 28.00 32.00 32.00

5.921 5.791 5.675 5.921 5.791 5.675 5.921 5.791 5.675 6.135 6.049 6.049 5.921 6.049 5.921 5.921 5.791 5.675 5.921 5.791 6.049 5.921 5.791 5.675 5.921 5.791 5.675 5.675

5.796 5.666 5.550 5.796 5.666 5.550 5.796 5.666 5.550 6.010 5.924 5.924 5.796 5.924 5.796 5.796 5.666 5.550 5.796 5.666 5.924 5.796 5.666 5.550 5.796 5.666 5.550 5.550

7

C-75 C-75 C-75 C-75 C-75 C-75 C-90 C-90 C-90 C-90 C-90 C-90 C-90 C-90 C-90 C-90

23.00 26.00 29.00 32.00 35.00 38.00 23.00 26.00 29.00 32.00 35.00 38.00 41.00 42.70 46.40 50.10

6.366 6.276 6.184 6.094 6.004 5.920 6.366 6.276 6.184 6.094 6.004 5.920 5.820 5.750 5.626 5.500

6.241 6.151 6.059 5.969 5.879 5.795 6.241 6.151 6.059 5.969 5.879 5.795 5.695 5.625 5.500 5.375

Drift Dia. In.

O.D. of Box In.


— — — — — — — —

— — — — — — — —

1,540 2,780 3,620 4,740 5,690 7,180 10,380 12,380

7.390 7.390 7.390 — — — 7.390 7.390 7.390 7.390 7.390 7.390 7.390 7.390 7.390 — — — — — — 7.390 7.390 7.390 7.390 7.390 7.390 —

5.73 5.666 5.55 — — — 5.73 5.666 5.55 — — — 5.73 — 5.73 — — — — — — 5.73 5.666 5.55 5.73 5.666 5.55 —

7.000 7.000 7.000 — — — 7.000 7.000 7.000 — — — 7.000 — 7.000 — — — — — — 7.000 7.000 7.000 7.000 7.000 7.000 —

5,570 7,830 9,830 6,140 8,880 11,330 6,290 9,200 11,800 1,370 2,520 2,970 4,560 2,970 4,560 5,760 8,170 10,320 5,080 7,010 3,190 5,760 8,170 10,320 6,710 10,140 13,200 14,530

7.656 7.656 7.656 7.656 7.656 7.656 — — — — — — — — — —

6.151 6.151 6.059 5.969 5.879 5.795 — — — — — — — — — —

7.390 7.390 7.390 7.390 7.530 7.530 — — — — — — — — — —

3,770 5,250 6,760 8,230 9,710 10,680 4,030 5,740 7,580 9,380 11,170 12,820 13,900 14,640 15,930 17,220


Page 23 NO. 203


Round Thread

Buttress Thd.



Ext. Line t

Short

Long

— — — — — — — —

1,740 3,360 4,620 — — — — —

— — — 6,720 7,560 8,870 12,190 13,920

— — — — — — — —

107 206 283 412 461 536 737 833

108 179 239 — — — — —

— — 279 323 366 432 565 646

— — — — — — — —

— — — — — — — —

6,970 8,260 9,410 8,370 9,910 11,290 8,830 10,460 11,920 — 3,040 4,180 5,110 4,180 5,110 7,440 8,810 10,040 6,040 7,160 4,940 7,440 8,810 10,040 10,230 12,120 13,800 15,680

— — — — — — — — — 1,620 3,040 4,180 5,110 4,180 5,110 — — — 6,040 — 4,940 — — — — — — —

6,970 8,260 9,410 8,370 9,910 11,290 8,830 10,460 11 920 — — 4,180 5,110 4,180 5,110 7,440 8,810 10,040 6,040 7,160 4,940 7,440 8,810 10,040 10,230 12,120 13,800 15,680

6,970 8,260 9,200 8,370 9,910 11,050 8,830 10,460 11,660 — — 4,180 5,110 4,180 5,110 7,440 8,810 9,820 6,040 7,160 4,940 7,440 8,810 9,820 10,230 12,120 13,500 15,340

520 610 688 624 732 826 659 773 872 123 229 315 382 315 382 555 651 734 451 529 373 555 651 734 763 895 1,009 1,147

— — — — — — — — — 121 184 245 314 267 342 — — — 366 — 285 — — — — — — —

453 552 638 520 633 732 546 665 769 — — 266 340 290 372 473 576 666 397 483 309 481 586 677 641 781 904 989

583 683 771 633 742 837 665 780 880 — — 374 453 453 548 592 693 783 518 607 428 615 721 814 786 922 1,040 1,138

605 648 717 — — — 668 716 793 — — — 477 — 605 — — — — — — 637 682 755 796 852 944 —

5,940 6,790 7,650 8,490 9,340 10,120 7,130 8,140 9,180 10,190 11,210 12,150 13,280 14,060 15,460 16,880

— — — — — — — — — — — — — — — —

5,940 6,790 7,650 8,490 8,660 8,660 7,130 8,140 9,180 10,190 10,390 10,390 10,390 — — —

5,940 6,790 7,650 7,930 7,930 7,930 7,130 8,140 9,180 9,520 9,520 9,520 9,520 — — —

499 566 634 699 763 822 599 679 760 839 915 986 — 1,127 1,226 1,325

— — — — — — — — — — — — 1,069 — — —

416 489 562 633 703 767 479 563 648 729 809 883 — — — —

557 631 707 779 833 833 605 687 768 847 876 876 903 — — —

632 641 685 761 850 917 — — — — — — 876 — — —



Page 24 TABLE


7

Grade

C-90 C-90 C-95 C-95 C-95 C-95 C-95 C-95 F-25* H2S-90 H2S-90 H2S-90ª H2S-90ª H2S-90ª H2S-90ª H2S-90ª H2S-90*ª H2S-95 H2S-95ª H2S-95ª H2S-95ª H2S-95ª H2S-95*ª H-40 H-40 HCL-80ª HCL-80ª HCL-80ª HCL-80ª HCL-80ª HCL-80ª HCN-80ª HCN-80ª HCN-80ª HCN-80ª HCN-80ª HCN-80ª H-110ª H-110ª HCQ-125ª J-55 J-55 J-55 K-55 K-55 K-55 L-80 L-80 L-80 L-80ª L-80ª L-80ª LS-140ª LS-140ª

Thread & lg.


Inside Dia. In.

53.60 57.10 23.00 26.00 29.00 32.00 35.00 38.00 17.00 23.00 23.00 26.00 29.00 32.00 35.00 38.00 41.00 26.00 29.00 32.00 35.00 38.00 41.00 17.00 20.00 23.00 26.00 29.00 32.00 35.00 38.00 23.00 26.00 29.00 32.00 35.00 38.00 26.00 29.00 29.00 20.00 23.00 26.00 20.00 23.00 26.00 29.00 35.00 38.00 23.00 26.00 32.00 32.00 35.00

5.376 5.250 6.366 6.276 6.184 6.094 6.004 5.920 6.538 6.366 6.366 6.276 6.184 6.094 6.004 5.920 5.820 6.276 6.184 6.094 6.004 5.920 5.820 6.538 6.456 6.366 6.276 6.184 6.094 6.004 5.920 6.366 6.276 6.184 6.094 6.004 5.920 6.276 6.184 6.184 6.456 6.366 6.276 6.456 6.366 6.276 6.184 6.004 5.920 6.366 6.276 6.094 6.094 6.004

Drift Dia. In.

O.D. of lg. In.

5.251 5.125 6.241 6.151 6.059 5.969 5.879 5.795 6.413 6.241 6.241 6.151 6.059 5.969 5.879 5.795 5.695 6.151 6.059 5.969 5.879 5.795 5.695 6.413 6.331 6.241 6.151 6.059 5.969 5.879 5.795 6.241 6.151 6.059 5.969 5.879 5.795 6.151 6.059 6.059 6.331 6.241 6.151 6.331 6.241 6.151 6.059 5.879 5.795 6.241 6.151 5.969 5.969 5.879

— — 7.656 7.656 7.656 7.656 7.656 7.656 7.656 — — — — — — — — — — — — — — 7.656 7.656 — — — — — — — — — — — — — — — 7.656 7.656 7.656 7.656 7.656 7.656 — — — — — — — —


— — 6.151 6.151 6.059 5.969 5.879 5.795 — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — 6.151 6.151 — 6.151 6.151 — — — — — — — —

O.D. of Box In.

— — 7.390 7.390 7.390 7.390 7.530 7.530 — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — 7.390 7.390 — 7.390 7.390 — — — — — — — —


18,460 19,690 4,150 5,870 7,820 9,730 11,640 13,420 1,100 5,650 5,650 7,300 9,200 10,400 11,600 12,820 13,900 7,800 9,200 10,400 11,650 13,440 14,670 1,450 1,980 5,650 7,800 9,200 10,400 11,600 12,700 5,650 7,800 9,200 10,400 11,600 12,700 7,800 9,200 9,200 2,270 3,270 4,320 2,270 3,270 4,320 7,020 10,180 11,390 3,830 5,410 8,610 12,540 15,490


Page 25 NO. 203


18,270 19,690 7,530 8,600 9,690 10,760 11,830 12,820 12,830 7,130 7,530 8,150 9,180 10,190 11,210 12,150 13,280 8,600 9,690 10,760 — 11,830 14,010 2,310 2,720 6,340 7,240 8,160 9,060 9,960 10,800 6,340 7,240 8,160 9,060 9,960 10,800 9,950 11,220 12,750 3,740 4,360 4,980 3,740 4,360 4,980 8,160 9,960 10,800 6,340 7,240 9,060 15,850 17,430

Round Thread Short

Long

Buttress Thd.

— — — — — — — — — — — — — — — — — — — — 1,440 — — 2,310 2,720 — — — — — — — — — — — — — — — 3,740 4,360 4,980 3,740 4,360 4,980 — — — — — — — —

— — 7,530 8,600 9,690 10,760 10,970 10,970 10,970 7,130 7,530 8,150 9,180 10,190 10,390 10,390 10,390 8,600 9,690 10,760 — 10,970 10,970 — — 6,340 7,240 8,160 9,060 9,240 9,240 6,340 7,240 8,160 9,060 9,240 9,240 9,950 11,220 12,750 — 4,360 4,980 — 4,360 4,980 8,160 9,240 9,240 6,340 7,240 9,060 15,850 16,170

— — 7,530 8,600 9,690 10,050 10,050 10,050 10,050 7,130 7,530 8,150 9,180 9,520 9,520 9,520 9,520 8,600 9,690 10,050 — 10,050 10,050 — — 6,340 7,240 8,160 8,460 8,460 8,460 6,340 7,240 8,160 8,460 8,460 8,460 9,950 11,220 12,750 — 4,360 4,980 — 4,360 4,980 8,160 8,460 8,460 6,340 7,240 8,460 14,810 14,810



1,421 1,515 632 717 803 885 966 1,041 1,041 599 632 679 760 839 915 986 1,069 717 803 885 123 966 1,129 196 230 532 604 676 745 814 877 532 604 676 745 814 877 830 929 1,056 316 366 415 316 366 415 676 814 877 532 604 745 1,304 1,424


— — — — — — — — — — — — — — — — — — — — 118 — — 122 176 — — — — — — — — — — — — — — — 234 284 334 254 309 364 — — — — — — — —


— — 505 593 683 768 853 931 931 485 505 570 655 738 819 883 903 593 683 768 — 853 952 — — 485 570 655 738 819 831 485 570 655 738 819 831 693 797 885 — 313 367 — 341 401 587 734 801 435 511 661 1,107 1,229

— — 636 722 808 891 920 920 920 614 636 696 780 860 876 876 876 722 808 891 — 920 920 — — 614 696 780 832 832 832 614 696 780 860 876 876 853 955 1,045 — 432 490 — 522 592 718 833 832 565 641 791 1,283 1,315

Ext. Line t

— — 699 709 757 841 940 1,013 — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — 499 506 — 632 641 — — — — — — — —

Page 26 TABLE

DIMENSIONS AND Thread & lg.

Grade


Inside Dia. In.

7

LS-140ª LS-65 LS-65 LS-65ª LS-65ª N-80 N-80 N-80 N-80 N-80 N-80 P-110 P-110 P-110 P-110 P-110 P-110ª Q-125ª Q-125ª Q-125ª Q-125ª Q-125*ª S-95ª S-95ª S-95 S-95 S-95ª S-95ª T-95 T-95 T-95 T-95 T-95 T-95 T-95 T-95 T-95 T-95 T-95 T-95 V-150 V-150* V-150* V-150* V-150*

38.00 23.00 29.00 20.00 26.00 23.00 26.00 29.00 32.00 35.00 38.00 26.00 29.00 32.00 35.00 38.00 41.00 29.00 32.00 35.00 38.00 41.00 23.00 26.00 29.00 32.00 35.00 38.00 23.00 26.00 29.00 32.00 35.00 38.00 41.00 42.70 46.40 50.10 53.60 57.10 41.00 29.00 32.00 35.00 38.00

75/8

C-75 C-75 C-75 C-75 C-90 C-90 C-90 C-90

26.40 29.70 33.70 39.00 26.40 29.70 33.70 39.00

Size O.D. In.


O.D. of Box In.


Drift Dia. In.

O.D. of lg. In.

5.920 6.366 6.184 6.456 6.276 6.366 6.276 6.184 6.094 6.004 5.920 6.276 6.184 6.094 6.004 5.920 5.820 6.184 6.094 6.004 5.920 5.820 6.366 6.276 6.184 6.094 6.004 5.920 6.366 6.276 6.184 6.094 6.004 5.920 5.820 5.750 5.626 5.500 5.376 5.250 5.820 6.184 6.094 6.004 5.920

5.795 6.241 6.059 6.331 6.151 6.241 6.151 6.059 5.969 5.879 5.795 6.151 6.059 5.969 5.879 5.795 5.695 6.059 5.969 5.879 5.795 5.695 6.241 6.151 6.059 5.969 5.879 5.795 6.241 6.151 6.059 5.969 5.879 5.795 5.695 5.625 5.500 5.375 5.251 5.125 5.695 6.059 5.969 5.879 5.795

— — — — — 7.656 7.656 7.656 7.656 7.656 7.656 7.656 7.656 7.656 7.656 7.656 — — — — — — — — — — — — — — — — — — — — — — — — — 7.656 7.656 7.656 7.656

— — — — — 6.151 6.151 6.059 5.969 5.879 5.795 6.151 6.059 5.969 5.879 5.795 — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

— — — — — 7.390 7.390 7.390 7.390 7.530 7.530 7.390 7.390 7.390 7.530 7.530 — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

18,280 3,540 6,090 2,480 4,800 3,830 5,410 7,020 8,600 10,180 11,390 6,210 8,510 10,760 13,010 15,110 16,990 9,100 11,720 14,310 16,750 19,300 5,650 7,800 9,200 10,400 11,650 13,440 4,140 8,600 7,830 9,750 11,650 13,440 14,670 15,450 16,820 18,810 19,480 20,780 22,820 9,800 13,020 16,230 19,240

6.969 6.875 6.765 6.625 6.969 6.875 6.765 6.625

6.844 6.750 6.640 6.500 6.844 6.750 6.640 6.500

8.500 8.500 8.500 8.500 — — — —

6.75 6.75 6.64 6.5 — — — —

8.010 8.010 8.010 8.010 — — — —

3,280 4,670 6,320 8,430 3,610 5,040 7,050 9,620


Page 27 NO. 203


Round Thread



Short

Long

Buttress Thd.

18,900 5,150 6,630 4,420 5,880 6,340 7,240 8,160 9,060 9,960 10,800 9,960 11,220 12,460 13,700 14,850 16,230 12,750 14,160 15,560 16,880 18,440 7,530 8,600 9,690 10,760 11,830 12,830 7,530 8,600 9,690 10,760 11,830 12,830 14,010 14,840 16,320 17,810 19,290 20,780 22,130 — — — —

— 5,150 — 4,420 5,880 — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

16,170 5,150 6,630 4,420 5,880 6,340 7,240 8,160 9,060 9,240 9,240 9,960 11,220 12,460 12,700 12,700 12,700 12,750 14,160 14,330 14,430 14,430 7,530 8,600 9,690 10,760 10,970 10,970 7,530 8,600 9,690 10,760 10,970 10,970 10,970 — — — — — 17,320 15,300 16,990 17,320 17,320

14,810 5,150 6,630 4,420 5,880 6,340 7,240 8,160 8,460 8,460 8,460 9,960 11,220 11,640 11,640 11,640 11,640 12,750 13,220 13,220 13,220 13,220 7,530 8,600 9,690 10,050 10,050 10,050 7,530 8,600 9,690 10,050 10,050 10,050 10,050 — — — — — 15,870 15,300 15,870 15,870 15,870

1,534 433 549 374 491 532 604 676 745 814 877 830 929 1,025 1,119 1,205 1,307 1,056 1,165 1,272 1,370 1,485 632 717 803 885 966 1,041 632 717 803 885 966 1,041 1,129 1,189 1,294 1,399 1,500 1,600 1,782 1,267 1,398 1,526 1,644

— 331 — 272 389 — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

1,341 364 492 300 428 442 519 597 672 746 814 693 797 897 996 1,087 1,111 885 996 1,106 1,207 1,244 512 602 692 779 865 944 505 593 683 768 853 931 952 — — — — — 1,488 1,049 1,180 1,311 1,430

1,315 494 628 427 561 588 667 746 823 876 876 853 955 1,053 1,096 1,096 1,096 1,045 1,152 1,183 1,183 1,183 659 747 836 922 964 964 636 722 808 891 920 920 920 — — — — — 1,402 1,296 1,363 1,363 1,363

— — — — — 666 675 721 801 895 965 844 902 1,002 1,118 1,207 — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

5,650 6,450 7,400 8,610 6,780 7,750 8,880 10,330

— — — — — — — —

5,650 6,450 7,400 8,610 6,780 7,750 8,880 10,330

5,650 6,450 7,400 8,610 6,780 7,750 8,880 10,330

564 641 729 839 677 769 875 1,007

— — — — — — — —

461 542 635 751 532 625 733 867

624 709 806 929 681 773 880 1,013

700 700 766 851 — — — —



Ext. Line t

Page 28 TABLE


75/8

Grade

C-90 C-90 C-90 C-90 C-90 C-95 C-95 C-95 C-95 C-95 C-95ª C-95ª F-25* H2S-90ª H2S-90ª H2S-90ª H2S-90ª H2S-90ª H2S-95 H2S-95ª H2S-95ª H2S-95ª H2S-95ª H-40 HCL-80ª HCL-80ª HCL-80ª HCL-80ª HCL-80ª HCN-80ª HCN-80ª HCN-80ª HCN-80ª HCN-80ª H-110ª H-110ª H-110ª HCQ-125ª J-55 K-55 L-80 L-80ª L-80ª L-80ª L-80ª L-80ª L-80ª LS-140ª LS-140ª LS-65ª LS-65ª N-80 N-80 N-80

Thread & lg.


Inside Dia. In.

42.80 45.30 47.10 51.20 55.30 26.40 29.70 33.70 39.00 45.30 42.80 47.10 20.00 26.40 29.70 33.70 39.00 45.30 45.30 26.40 29.70 33.70 39.00 24.00 26.40 29.70 33.70 39.00 45.30 26.40 29.70 33.70 39.00 45.30 26.40 29.70 33.70 33.70 26.40 26.40 47.10 26.40 29.70 33.70 39.00 42.80 45.30 33.70 39.00 26.40 29.70 26.40 29.70 33.70

6.501 6.435 6.375 6.251 6.125 6.969 6.875 6.765 6.625 6.435 6.501 6.375 7.125 6.969 6.875 6.765 6.625 6.435 6.435 6.969 6.875 6.765 6.625 7.025 6.969 6.875 6.765 6.625 6.435 6.969 6.875 6.765 6.625 6.435 6.969 6.875 6.765 6.765 6.969 6.969 6.375 6.969 6.875 6.765 6.625 6.501 6.435 6.765 6.625 6.969 6.875 6.969 6.875 6.765

Drift Dia. In.

O.D. of lg. In.

6.376 6.310 6.250 6.126 6.000 6.844 6.750 6.640 6.500 6.310 6.376 6.250 7.000 6.844 6.750 6.640 6.500 6.310 6.310 6.844 6.750 6.640 6.500 6.900 6.844 6.750 6.640 6.500 6.310 6.844 6.750 6.640 6.500 6.310 6.844 6.750 6.640 6.640 6.844 6.844 6.250 6.844 6.750 6.640 6.500 6.376 6.310 6.640 6.500 6.844 6.750 6.844 6.750 6.640

— — — — — 8.500 8.500 8.500 8.500 — — — 8.500 — — — — — — — — — — 8.500 — — — — — — — — — — — — — — 8.500 8.500 — — — — — — — — — — — 8.500 8.500 8.500


— — — — — 6.75 6.75 6.64 6.5 — — — — — — — — — — — — — — — — — — — — — — — — — — — — — 6.75 6.75 — — — — — — — — — — — 6.75 6.75 6.64

O.D. of Box In.

— — — — — 8.010 8.010 8.010 8.010 — — — — — — — — — — — — — — — — — — — — — — — — — — — — — 8.010 8.010 — — — — — — — — — — — 8.010 8.010 8.010


11,890 12,950 13,540 14,760 15,960 3,710 5,120 7,260 9,980 13,660 12,410 14,300 1,100 4,850 7,150 8,800 10,600 12,950 13,660 4,850 7,150 8,800 10,600 2,040 4,850 7,150 8,800 10,600 12,900 4,850 7,150 8,800 10,600 12,900 4,850 7,150 8,800 8,800 2,890 2,890 12,040 3,400 4,790 6,560 8,820 10,810 11,510 8,690 12,930 3,100 4,310 3,400 4,790 6,560


Page 29 NO. 203


11,610 12,290 12,910 14,190 15,490 7,150 8,180 9,380 10,900 12,970 12,250 13,630 — 6,780 7,750 8,880 10,330 12,290 12,970 7,150 8,180 9,380 10,900 2,750 6,020 6,890 7,900 9,180 10,920 6,020 6,890 7,900 9,180 10,920 8,280 9,470 10,860 12,340 4,140 4,140 11,480 6,020 6,890 7,900 9,180 10,320 10,920 13,820 16,070 4,890 5,590 6,020 6,890 7,900

Round Thread Short

Long

— — — — — — — — — — — — 1,430 — — — — — — — — — — 2,750 — — — — — — — — — — — — — — 4,140 4,140 — — — — — — — — — 4,890 — — — —

11,610 11,810 11,810 — — 7,150 8,180 9,380 10,900 12,460 12,250 12,460 — 6,780 7,750 8,880 10,330 11,810 12,460 7,150 8,180 9,380 10,900 — 6,020 6,890 7,900 9,180 10,490 6,020 6,890 7,900 9,180 10,490 8,280 9,470 10,860 12,340 4,140 4,140 10,490 6,020 6,890 7,900 9,180 10,320 10,490 13,820 16,070 4,890 5,590 6,020 6,890 7,900


Buttress Thd.

11,010 11,010 11,010 7,150 8,180 9,380 10,900 11,620 11,620 11,620 145 6,780 7,750 8,880 10,330 11,010 11,620 7,150 8,180 9,380 10,900 276 6,020 6,890 7,900 9,180 9,790 6,020 6,890 7,900 9,180 9,790 8,280 9,470 10,860 12,340 4,140 4,140 9,790 6,020 6,890 7,900 9,180 9,790 9,790 13,820 16,070 4,890 5,590 6,020 6,890 7,900


1,122 1,183 1,237 1,348 1,458 714 811 923 1,063 1,248 1,185 1,306 138 677 769 875 1,007 1,183 1,248 714 811 923 1,063 212 602 683 778 895 1,051 602 683 778 895 1,051 827 940 1,069 1,215 414 414 1,100 602 683 778 895 998 1,051 1,361 1,567 489 555 602 683 778


— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — 315 342 — — — — — — — — — 368 — — — —


983 1,045 1,100 — — 560 659 772 914 1,101 1,037 1,159 — 553 650 762 901 1,086 1,101 560 659 772 914 — 533 650 762 901 1,086 553 650 762 901 1,086 654 769 901 1,009 346 377 997 482 566 664 786 891 947 1,128 1,335 403 474 490 575 674

1,129 1,189 1,238 — — 716 813 925 1,065 1,251 1,187 1,300 — 691 785 894 1,029 1,208 1,251 716 813 925 1,065 — 691 785 894 1,029 1,177 691 785 894 1,029 1,208 845 960 1,093 1,197 483 581 1,160 635 721 820 945 1,053 1,109 1,334 1,536 554 629 659 749 852

Ext. Line t

— — — — — 774 774 846 941 — — — — — — — — — — — — — — — — — — — — — — — — — — — — — 553 700 — — — — — — — — — — — 737 737 806

Page 30 TABLE


Thread & lg.

Grade


Inside Dia. In.

75/8

N-80 N-80ª N-80ª N-80ª P-110 P-110 P-110 P-110ª P-110ª P-110ª Q-125 Q-125ª Q-125ª Q-125ª Q-125ª S-95 S-95ª S-95ª S-95ª S-95ª T-95 T-95 T-95 T-95 T-95 T-95 T-95 T-95 T-95 V-150 V-150 V-150

39.00 42.80 45.30 47.10 29.70 33.70 39.00 42.80 45.30 47.10 45.30 33.70 39.00 42.80 47.10 45.30 26.40 29.70 33.70 39.00 26.40 29.70 33.70 39.00 42.80 45.30 47.10 51.20 55.30 33.70 39.00 45.30

73/4

C-90 C-95 H2S-90 H2S-95 HCL-80ª L-80 LS-140ª P-110 Q-125 S-95ª T-95

85/8

C-75 C-75 C-75 C-75 C-90 C-90 C-90 C-95 C-95

Size O.D. In.

Drift Dia. In.

O.D. of Box In.


Drift Dia. In.

O.D. of lg. In.

6.625 6.501 6.435 6.375 6.875 6.765 6.625 6.501 6.435 6.375 6.435 6.765 6.625 6.501 6.375 6.435 6.969 6.875 6.765 6.625 6.969 6.875 6.765 6.625 6.501 6.435 6.375 6.251 6.125 6.765 6.625 6.435

6.500 6.376 6.310 6.250 6.750 6.640 6.500 6.376 6.310 6.250 6.310 6.640 6.500 6.376 6.250 6.310 6.844 6.750 6.640 6.500 6.844 6.750 6.640 6.500 6.376 6.310 6.250 6.126 6.000 6.640 6.500 6.310

8.500 — — — 8.500 8.500 8.500 — — — — — — — — — — — — — — — — — — — — — — 8.500 8.500 8.500

6.5 — — — 6.75 6.64 6.5 — — — — — — — — — — — — — — — — — — — — — — — — —

8.010 — — — 8.010 8.010 8.010 — — — — — — — — — — — — — — — — — — — — — — — — —

8,810 10,810 11,510 12,040 5,340 7,850 11,060 13,920 15,430 16,550 17,090 8,350 12,060 15,350 18,700 13,660 4,850 7,150 8,800 10,600 3,710 5,140 7,280 10,000 12,410 13,660 14,300 15,580 16,850 8,860 13,450 19,680

46.10 46.10 46.10 46.10 46.10 46.10 46.10 46.10 46.10 46.10 46.10

6.560 6.560 6.560 6.560 6.560 6.560 6.560 6.560 6.560 6.560 6.560

6.435 6.435 6.435 6.435 6.435 6.435 6.435 6.435 6.435 6.435 6.435

— — — — — — — — — — —

— — — — — — — — — — —

— — — — — — — — — — —

12,740 13,320 12,740 13,320 13,320 11,340 18,090 14,990 16,580 13,320 13,320

36.00 40.00 44.00 49.00 40.00 44.00 49.00 36.00 40.00

7.825 7.725 7.625 7.511 7.725 7.625 7.511 7.825 7.725

7.700 7.600 7.500 7.386 7.600 7.500 7.386 7.700 7.600

9.625 9.625 9.625 9.625 — — — 9.625 9.625

7.7 7.6 7.5 7.386 — — — 7.7 7.6

9.120 9.120 9.120 9.120 — — — 9.120 9.120

4,020 5,350 6,680 8,200 5,870 7,490 9,340 4,360 6,010


Page 31 NO. 203


Round Thread Short

Long

Buttress Thd.



Ext. Line t

9,180 10,320 10,920 11,480 9,470 10,860 12,620 14,190 15,020 15,780 17,070 12,340 14,340 16,120 17,930 12,970 7,150 8,180 9,380 10,900 7,150 8,180 9,380 10,900 12,250 12,970 13,630 14,980 16,350 — — —

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

9,180 10,320 10,490 10,490 9,470 10,860 12,620 14,190 14,430 14,430 16,400 12,340 14,340 16,120 16,400 12,460 7,150 8,180 9,380 10,900 7,159 8,180 9,380 10,900 12,250 12,460 12,460 — — 14,800 17,210 19,680

9,180 9,790 9,790 9,790 9,470 10,860 12,620 13,460 13,460 13,460 15,290 12,340 14,340 15,290 15,290 11,620 7,150 8,180 9,380 10,900 7,150 8,180 9,380 10,900 11,620 11,620 11,620 — — 14,800 17,210 18,350

895 998 1,051 1,100 940 1,069 1,231 1,372 1,446 1,512 1,643 1,215 1,399 1,559 1,718 1,248 714 811 923 1,063 714 811 923 1,063 1,185 1,248 1,306 1,423 1,539 1,458 1,679 1,971

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

798 905 962 1,013 769 901 1,066 1,210 1,285 1,353 1,439 1,009 1,194 1,355 1,515 1,116 568 668 783 926 560 659 772 914 1,037 1,101 1,159 — — 1,207 1,428 1,721

981 1,093 1,152 1,205 960 1,093 1,258 1,402 1,477 1,545 1,619 1,197 1,379 1,536 1,672 1,293 740 841 957 1,101 716 813 925 1,065 1,187 1,251 1,300 — — 1,482 1,706 1,932

896 — — — 922 1,008 1,120 — — — — — — — — — — — — — — — — — — — — — — — — —

12,090 12,760 12,090 12,760 10,750 10,750 18,810 14,780 16,790 12,760 12,760

— — — — — — — — — — —

11,810 12,460 11,810 12,460 10,490 10,490 18,360 14,430 16,400 12,460 12,460

11,010 11,620 11,010 11,620 9,790 9,790 17,130 13,460 15,290 11,620 11,620

1,204 1,271 1,204 1,271 1,070 1,070 1,872 1,471 1,672 1,271 1,271

— — — — — — — — — — —

928 978 965 978 965 841 1,429 1,142 1,279 992 978

1,074 1,129 1,091 1,129 1,091 1,001 1,628 1,334 1,462 1,168 1,129

— — — — — — — — — — —

6,090 6,850 7,610 8,480 8,220 9,130 10,170 7,710 8,670

— — — — — — — — —

6,090 6,850 7,610 8,480 8,220 9,130 10,170 7,710 8,670

6,090 6,850 7,610 8,480 8,220 9,130 10,170 7,710 8,670

775 867 957 1,059 1,040 1,149 1,271 982 1,098

— — — — — — — — —

648 742 834 939 858 965 1,085 789 904

847 947 1,046 1,157 1,038 1,146 1,268 976 1,092

871 942 1,007 1,007 — — — 963 1,042



Page 32 TABLE


85/8

Grade

C-95 C-95 F-25* H2S-90ª H2S-90ª H2S-90ª H2S-95ª H2S-95ª H2S-95ª H-40 H-40 HCK-55ª HCK-55ª HCK-55ª HCK-55ª HCL-80ª HCL-80ª HCL-80ª HCL-80ª HCN-80ª HCN-80ª HCN-80ª HCN-80ª H-110ª H-110ª HCQ-125ª J-55 J-55 J-55 J-55ª K-55ª K-55 K-55 L-80 L-80ª L-80ª L-80ª LS-65ª LS-65ª LS-65ª LS-65ª N-80 N-80 N-80 N-80 P-110 P-110 P-110 Q-125ª Q-125ª S-95 S-95ª S-95ª

Thread & lg.


Inside Dia. In.

44.00 49.00 24.00 40.00 44.00 49.00 40.00 44.00 49.00 28.00 32.00 24.00 28.00 32.00 36.00 36.00 40.00 44.00 49.00 36.00 40.00 44.00 49.00 40.00 44.00 44.00 24.00 32.00 36.00 24.00 24.00 32.00 36.00 36.00 40.00 44.00 49.00 24.00 32.00 36.00 40.00 36.00 40.00 44.00 49.00 40.00 44.00 49.00 44.00 49.00 49.00 40.00 44.00

7.625 7.511 8.097 7.725 7.625 7.511 7.725 7.625 7.511 8.017 7.921 8.097 8.017 7.921 7.825 7.825 7.725 7.625 7.511 7.825 7.725 7.625 7.511 7.725 7.625 7.625 8.097 7.921 7.825 8.097 8.097 7.921 7.825 7.825 7.725 7.625 7.511 8.097 7.921 7.825 7.725 7.825 7.725 7.625 7.511 7.725 7.625 7.511 7.625 7.511 7.511 7.725 7.625

Drift Dia. In.

O.D. of lg. In.

7.500 7.386 7.972 7.600 7.500 7.386 7.600 7.500 7.386 7.892 7.796 7.972 7.892 7.796 7.700 7.700 7.600 7.500 7.386 7.700 7.600 7.500 7.386 7.600 7.500 7.500 7.972 7.796 7.700 7.972 7.972 7.796 7.700 7.700 7.600 7.500 7.386 7.972 7.796 7.700 7.600 7.700 7.600 7.500 7.386 7.600 7.500 7.386 7.500 7.386 7.386 7.600 7.500

9.625 9.625 9.625 — — — — — — 9.625 9.625 — — — — — — — — — — — — — — — 9.625 9.625 9.625 — 9.625 9.625 9.625 — — — — — — — — 9.625 9.625 9.625 9.625 9.625 9.625 9.625 — — — — —


7.5 7.386 — — — — — — — — — — — — — — — — — — — — — — — — — 7.7 7.7 — — 7.7 7.7 — — — — — — — — 7.7 7.6 7.5 7.386 7.6 7.5 7.386 — — — — —

O.D. of Box In.

9.120 9.120 — — — — — — — — — — — — — — — — — — — — — — — — — 9.120 9.120 — — 9.120 9.120 — — — — — — — — 9.120 9.120 9.120 9.120 9.120 9.120 9.120 — — — — —


7,730 9,690 950 7,900 9,100 10,400 7,900 9,100 10,400 1,640 2,210 1,780 2,680 4,130 5,300 6,060 7,900 9,100 10,400 6,060 7,900 9,100 10,400 7,900 9,100 9,100 1,370 2,530 3,450 1,370 1,370 2,530 3,450 4,100 5,520 6,950 8,580 1,430 2,740 3,760 4,890 4,100 5,520 6,950 8,570 6,380 8,400 10,720 8,980 11,650 10,400 7,900 9,100


Page 33 NO. 203


9,640 10,740 1,340 8,220 9,130 10,170 8,670 9,640 10,740 2,470 2,860 2,950 3,390 3,930 4,460 6,490 7,300 8,120 9,040 6,490 7,300 8,120 9,040 10,040 11,160 12,680 2,950 3,930 4,460 2,950 2,950 3,930 4,460 6,490 7,300 8,120 9,040 3,480 4,640 5,280 5,930 6,490 7,300 8,120 9,040 10,040 11,160 12,430 12,680 14,130 10,740 8,670 9,640

Round Thread Short

Long

— — — — — — — — — 2,470 2,860 2,950 3,390 3,930 4,460 — — — — — — — — — — — 2,950 3,930 4,460 2,950 2,950 3,930 4,460 — — — — 3,480 4,640 5,280 — — — — — — — — — — — — —

9,640 10,740 173 8,220 9,130 10,170 8,670 9,640 10,740 — — — 3,390 3,930 4,460 6,490 7,300 8,120 9,040 6,490 7,300 8,120 9,040 10,040 11,160 12,680


3,930 4,460 — — 3,930 4,460 6,490 7,300 8,120 9,040 — 4,640 5,280 5,930 6,490 7,300 8,120 9,040 10,040 11,160 12,430 12,680 14,130 10,740 8,670 9,640

Buttress Thd.

9,640 10,740 161 8,220 9,130 10,170 8,670 9,640 10,740 318 366 — 3,390 3,930 4,460 6,490 7,300 8,120 9,040 6,490 7,300 8,120 9,040 10,040 11,160 12,680 381 3,930 4,460 — — 3,930 4,460 6,490 7,300 8,120 9,040 — 4,640 5,280 5,930 6,490 7,300 8,120 9,040 10,040 11,160 12,430 12,680 14,130 10,740 8,670 9,640


1,212 1,341 — 1,040 1,149 1,271 1,098 1,212 1,341 233 279 381 437 503 568 827 925 1,021 1,129 827 925 1,021 1,129 1,271 1,404 1,595 244 503 568 381 381 503 568 — 925 1,021 1,129 451 595 672 751 827 925 1,021 1,129 1,271 1,404 1,553 1,595 1,765 1,341 1,098 1,212


— — — — — — — — — — — 326 414 497 579 — — — — — — — — — — — — 372 434 244 263 402 468 827 — — — 302 435 506 — — — — — — — — — — — — —


1,017 1,144 — 892 1,004 1,129 904 1,017 1,144 — — — 464 556 648 779 892 1,004 1,129 779 892 1,004 1,129 1,055 1,186 1,330 — 417 486 — — 452 526 — 776 874 983 — 487 567 649 688 788 887 997 1,055 1,186 1,335 1,330 1,496 1,159 915 1,030

1,206 1,334 — 1,057 1,167 1,291 1,092 1,206 1,334 — — — 651 749 847 945 1,057 1,167 1,291 945 1,057 1,167 1,291 1,228 1,423 1,562 — 579 654 — — 690 780 678 966 1,066 1,180 — 664 751 839 895 1,001 1,105 1,222 1,288 1,423 1,574 1,562 1,728 1,377 1,127 1,244

Ext. Line t

1,113 1,113 — — — — — — — — — — — — — — — — — — — — — — — — — 686 688 — — 869 871 864 — — — — — — — 917 992 1,060 1,060 1,240 1,326 1,326 — — — — —

Page 34 TABLE


95/8

Inside Dia. In.

T-95 T-95 T-95 V-150* V-150*

40.00 44.00 49.00 44.00 49.00

C-75 C-75 C-75 C-75 C-90 C-90 C-90 C-90 C-90 C-90 C-90 C-90 C-90 C-95 C-95 C-95 C-95 C-95 F-25* H2S-90ª H2S-90ª H2S-90ª H2S-90ª H2S-95 H2S-95ª H2S-95ª H2S-95ª H-40 H-40 HCK-55ª HCK-55ª HCL-80ª HCL-80ª HCL-80ª HCL-80ª HCN-80ª HCN-80ª HCN-80ª HCN-80ª H-110ª H-110ª H-110*ª HCQ-125ª HCQ-125ª HCQ-125*ª J-55 J-55 K-55

40.00 43.50 47.00 53.50 40.00 43.50 47.00 53.50 58.40 59.40 64.90 70.30 75.60 40.00 43.50 47.00 53.50 58.40 29.30 47.00 40.00 43.50 53.50 40.00 43.50 47.00 53.50 32.30 36.00 36.00 40.00 40.00 43.50 47.00 53.50 40.00 43.50 47.00 53.50 43.50 47.00 53.50 43.50 47.00 53.50 36.00 40.00 36.00

Grade

Extreme Line

Thread & lg.


Drift Dia. In.

O.D. of Box In.


Drift Dia. In.

O.D. of lg. In.

7.725 7.625 7.511 7.625 7.511

7.600 7.500 7.386 7.500 7.386

— — — 9.625 9.625

— — — — —

— — — — —

6,020 7,740 9,710 9,640 12,950

8.835 8.755 8.681 8.535 8.835 8.755 8.681 8.535 8.435 8.407 8.281 8.157 8.031 8.835 8.755 8.681 8.535 8.435 9.063 8.681 8.835 8.755 8.535 8.835 8.755 8.681 8.535 9.001 8.921 8.921 8.835 8.835 8.755 8.681 8.535 8.835 8.755 8.681 8.535 8.755 8.681 8.535 8.755 8.681 8.535 8.921 8.835 8.921

8.679 8.599 8.525 8.379 8.679 8.599 8.525 8.379 8.279 8.251 8.125 8.001 7.875 8.679 8.599 8.525 8.379 8.279 8.907 8.525 8.679 8.599 8.379 8.679 8.599 8.525 8.379 8.845 8.765 8.765 8.679 8.679 8.599 8.525 8.379 8.679 8.599 8.525 8.379 8.599 8.525 8.379 8.599 8.525 8.379 8.765 8.679 8.765

10.625 10.625 10.625 10.625 — — — — — — — — — 10.625 10.625 10.625 10.625 — 10.625 — — — — — — — — 10.625 10.625 — — — — — — — — — — — — — — — — 10.625 10.625 10.625

8.599 8.599 8.525 8.379 — — — — — — — — — 8.599 8.599 8.525 8.379 — — — — — — — — — — — — — — — — — — — — — — — — — — — — — 8.599 —

10.100 10.100 10.100 10.100 — — — — — — — — — 10.100 10.100 10.100 10.100 — — — — — — — — — — — — — — — — — — — — — — — — — — — — — 10.100 —

2,980 3,750 4,630 6,380 3,250 4,010 5,000 7,120 8,560 8,980 10,800 12,610 13,670 3,330 4,130 5,080 7,330 8,880 860 7,100 4,230 5,600 8,850 4,230 5,600 7,100 8,850 1,400 1,740 2,980 4,230 4,230 5,600 7,100 8,850 4,230 5,600 7,100 8,850 5,600 7,100 8,850 5,600 7,100 8,850 2,020 2,570 2,020


Page 35 NO. 203


Round Thread Short

Long

Buttress Thd.



Ext. Line t

8,670 9,640 10,740 — —

— — — — —

8,670 9,640 10,740 15,220 16,950

8,670 9,640 10,740 15,220 16,950

1,098 1,212 1,341 1,914 2,118

— — — — —

904 1,017 1,144 1,591 1,789

1,092 1,206 1,334 1,925 2,130

— — — — —

5,390 5,930 6,440 7,430 6,460 7,120 7,720 8,920 9,740 9,970 11,000 12,010 13,040 6,820 7,510 8,150 9,410 10,280 — 7,720 6,460 7,120 8,920 6,820 7,510 8,150 9,410 2,270 2,560 3,520 3,950 5,750 6,330 6,870 7,930 5,750 6,330 6,870 7,930 8,700 9,440 10,900 9,890 10,730 12,390 3,520 3,950 3,520

— — — — — — — — — — — — — — — — — — 1,280 — — — — — — — — 2,270 2,560 3,520 3,950 — — — — — — — — — — — — — — 3,520 3,950 3,520

5,390 5,930 6,440 7,430 6,460 7,120 7,720 8,920 9,740 — — — — 6,820 7,510 8,150 9,410 10,280 — 7,720 6,460 7,120 8,920 6,820 7,510 8,150 9,410 — — 3,520 3,950 5,750 6,330 6,870 7,930 5,750 6,330 6,870 7,930 8,700 9,440 10,900 9,890 10,730 12,390 3,520 3,950 3,520

5,390 5,930 6,440 7,430 6,460 7,120 7,720 8,920 9,740 — — — — 6,820 7,510 8,150 9,410 10,280 206 7,720 6,460 7,120 8,920 6,820 7,510 8,150 9,410 365 410 3,520 3,950 5,750 6,330 6,870 7,930 5,750 6,330 6,870 7,930 8,700 9,440 10,900 9,890 10,730 12,390 3,520 3,950 3,520

859 942 1,018 1,166 1,031 1,130 1,221 1,399 1,519 1,553 1,701 1,845 1,989 1,088 1,193 1,289 1,477 1,604 185 1,221 1,031 1,130 1,399 1,088 1,193 1,289 1,477 254 294 564 630 916 1,005 1,086 1,244 916 1,005 1,086 1,244 1,381 1,493 1,710 1,570 1,697 1,943 564 630 564

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — 526 604 — — — — — — — — — — — — — — 394 452 423

694 776 852 999 804 899 987 1,157 1,272 — — — — 847 948 1,040 1,220 1,341 — 1,027 837 936 1,205 847 948 1,040 1,220 — — 605 694 837 936 1,027 1,205 837 936 1,027 1,205 1,106 1,213 1,422 1,240 1,361 1,595 453 520 489

926 1,016 1,098 1,257 1,021 1,119 1,210 1,386 1,504 — — — — 1,074 1,178 1,273 1,458 1,583 — 1,234 1,042 1,142 1,414 1,074 1,178 1,273 1,458 — — 829 926 1,042 1,142 1,234 1,414 1,042 1,142 1,234 1,414 1,388 1,500 1,718 1,527 1,650 1,890 639 714 755

975 975 1,032 1,173 — — — —



— — — — 1,078 1,078 1,141 1,297 — — — — — — — — — — — — — — — — — — — — — — — — — — — — — 770 —

Page 36 TABLE


Thread & lg.

Grade


Inside Dia. In.

95/8

K-55 L-80 L-80ª L-80ª L-80ª L-80ª LS-140ª LS-140ª LS-140ª LS-65ª LS-65ª LS-65ª N-80 N-80 N-80 N-80 N-80ª P-110 P-110 P-110ª P-110ª P-110 Q-125ª Q-125ª Q-125ª Q-125ª S-95 S-95 S-95ª S-95ª T-95 T-95 T-95 T-95 T-95 T-95 T-95 T-95 T-95 V-150* V-150* V-150* V-150*

40.00 40.00 43.50 47.00 53.50 58.40 43.50 47.00 53.50 36.00 40.00 43.50 40.00 43.50 47.00 53.50 58.40 43.50 53.50 43.50 58.40 47.00 43.50 47.00 53.50 58.40 43.50 40.00 47.00 53.50 40.00 43.50 47.00 53.50 58.40 59.40 64.90 70.30 75.60 53.50 58.40 61.10 71.80

8.835 8.835 8.755 8.681 8.535 8.435 8.755 8.681 8.535 8.921 8.835 8.755 8.835 8.755 8.681 8.535 8.435 8.755 8.535 8.755 8.435 8.681 8.755 8.681 8.535 8.435 8.755 8.835 8.681 8.535 8.835 8.755 8.681 8.535 8.435 8.407 8.281 8.157 8.031 8.535 8.435 8.375 8.125

93/4

H2S-90 H2S-95k H-110ª LS-140ª P-110ª Q-125ª S-95

59.20 59.20 59.20 59.20 59.20 59.20 59.20

8.560 8.560 8.560 8.560 8.560 8.560 8.560

Size O.D. In.

Drift Dia. In.

8.679 8.679 8.599 8.525 8.379 8.279 8.599 8.525 8.379 8.765 8.679 8.599 8.679 8.599 8.525 8.379 8.279 8.599 8.379 8.599 8.279 8.525 8.599 8.525 8.379 8.279 8.599 8.679 8.525 8.379 8.679 8.599 8.525 8.379 8.279 8.251 8.125 8.001 7.875 8.379 8.279 8.219 7.969 — — — — — — —

O.D. of lg. In.

Drift Dia. In.

O.D. of Box In.


10.625 — — — — — — — — — — — 10.625 10.625 10.625 10.625 — 10.625 10.625 — — 10.625 — — — — — — — — — — — — — — — — — 10.625 10.625 10.625 10.625

8.599 — — — — — — — — — — — 8.599 8.599 8.525 8.379 — 8.599 8.379 — — 8.525 — — — — — — — — — — — — — — — — — — — — —

10.100 — — — — — — — — — — — 10.100 10.100 10.100 10.100 — 10.100 10.100 — — 10.100 — — — — — — — — — — — — — — — — — — — — —

2,570 3,090 3,810 4,760 6,620 7,890 5,600 7,100 8,850 2,190 2,770 3,520 3,090 3,810 4,750 6,620 7,890 4,430 7,930 4,420 9,760 5,310 4,620 5,640 8,440 10,530 5,600 4,230 7,100 8,850 3,320 4,120 5,090 7,340 8,880 9,320 11,260 13,180 14,430 8,970 11,570 13,130 19,640

— — — — — — —

— — — — — — —

— — — — — — —

9,750 9,750 9,750 10,820 9,490 10,210 9,750


Page 37 NO. 203


Round Thread



Short

Long

Buttress Thd.

3,950 5,750 6,330 6,870 7,930 8,650 11,070 12,010 13,870 4,160 4,670 5,140 5,750 6,330 6,870 7,930 8,650 8,700 10,900 8,700 11,900 9,440 9,890 10,730 12,390 13,520 7,510 6,820 8,150 9,410 6,820 7,510 8,150 9,410 10,280 10,520 11,610 12,680 13,770 — — — —

3,950 — — — — — — — — 4,160 4,670 — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

3,950 5,750 6,330 6,870 7,930 8,650 11,070 12,010 13,870 4,160 4,670 5,140 5,750 6,330 6,870 7,930 8,650 8,700 10,900 8,700 11,900 9,440 9,890 10,730 12,390 13,520 7,510 6,820 8,150 9,410 6,820 7,510 8,150 9,410 10,280 — — — — 14,860 16,230 17,050 18,060

3,950 5,750 6,330 6,870 7,930 8,650 11,070 12,010 13,870 4,160 4,670 5,140 5,750 6,330 6,870 7,930 8,650 8,700 10,900 8,700 11,900 9,440 9,890 10,730 12,390 13,520 7,510 6,320 8,150 9,410 6,820 7,510 8,150 9,410 10,280 — — — — 14,860 16,230 16,560 16,560

630 916 1,005 1,086 1,244 1,350 1,758 1,900 2,177 667 745 816 916 1,005 1,086 1,244 1,350 1,381 1,710 1,381 1,857 1,493 1,570 1,697 1,943 2,110 1,193 1,088 1,289 1,477 1,088 1,193 1,289 1,477 1,604 1,634 1,796 1,948 2,100 2,332 2,532 2,651 3,136

486 — — — — — — — — 460 528 — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

561 727 813 893 1,047 1,151 1,386 1,521 1,783 529 608 679 737 825 905 1,062 1,167 1,106 1,422 1,106 1,564 1,213 1,240 1,361 1,595 1,754 959 858 1,053 1,235 847 948 1,040 1,220 1,341 — — — — 1,909 2,098 2,211 2,672

843 947 1,038 1,122 1,286 1,396 1,702 1,839 2,107 734 823 899 979 1,074 1,161 1,329 1,443 1,388 1,718 1,388 1,865 1,500 1,527 1,650 1,890 2,052 1,213 1,106 1,311 1,502 1,074 1,178 1,273 1,458 1,583 — — — — 2,321 2,519 2,638 2,692

975 — — — — — — — — — — — 1,027 1,027 1,086 1,235 — 1,283 1,544 — — 1,358 — — — — — — — — — — — — — — — — — — — — —

9,610 10,150 11,750 14,950 11,750 13,350 10,150

— — — — — — —

9,610 10,150 11,750 14,950 11,750 13,350 10,150

9,610 10,150 11,750 14,950 11,750 13,350 10,150

1,540 1,626 1,882 2,396 1,882 2,139 1,626

— — — — — — —

1,175 1,189 1,387 1,739 1,387 1,555 1,204

1,383 1,426 1,681 2,061 1,681 1,850 1,469

— — — — — — —



Ext. Line t

Page 38 TABLE


Thread & lg.

Grade


Inside Dia. In.

97/8

H2S-90 H2S-95k LS-140ª P-110ª Q-125ª S-95

62.80 62.80 62.80 62.80 62.80 62.80

8.625 8.625 8.625 8.625 8.625 8.625

103/4

C-75 C-75 C-90 C-90 C-90 C-90 C-90 C-90 C-90 C-95 C-95 C-95 C-95 F-25* H2S-90 H2S-90 H2S-90ª H2S-90ª H2S-90ª H2S-95 H2S-95 H2S-95 H2S-95ª H2S-95ª H-40 H-40 HCK-55ª HCK-55ª HCK-55ª HCK-55ª HCL-80ª HCL-80ª HCL-80ª HCL-80ª HCN-80ª HCN-80ª HCN-80ª HCN-80ª HCN-80ª HCN-80ª H-110ª H-110ª H-110ª H-110ª H-110ª HCQ-125 HCQ-125ª

51.00 55.50 51.00 55.50 60.70 65.70 73.20 79.20 85.30 51.00 55.50 60.70 65.70 32.75 51.00 60.70 55.50 65.70 71.10 51.00 55.50 71.10 60.70 65.70 32.75 40.50 40.50 45.50 51.00 55.50 51.00 55.50 60.70 65.70 40.50 45.50 51.00 55.50 60.70 65.70 51.00 55.50 60.70 65.70 71.10 60.70 51.00

9.850 9.760 9.850 9.760 9.660 9.560 9.406 9.282 9.156 9.850 9.760 9.660 9.560 10.192 9.850 9.660 9.760 9.560 9.450 9.850 9.760 9.450 9.660 9.560 10.192 10.050 10.050 9.950 9.850 9.760 9.850 9.760 9.660 9.560 10.050 9.950 9.850 9.760 9.660 9.560 9.850 9.760 9.660 9.560 9.450 9.660 9.850

Size O.D. In.

Drift Dia. In.

O.D. of lg. In.

Drift Dia. In.

O.D. of Box In.


— — — — — —

— — — — — —

— — — — — —

— — — — — —

10,180 10,180 11,870 10,280 11,140 10,180

9.694 9.604 9.694 9.604 9.504 9.404 9.250 9.126 9.000 9.694 9.604 9.504 9.404 10.036 9.694 9.504 9.604 9.404 9.294 9.694 9.604 9.294 9.504 9.404 10.036 9.894 9.894 9.794 9.694 9.604 9.694 9.604 9.504 9.404 9.894 9.875 9.694 9.604 9.504 9.404 9.694 9.604 9.504 9.404 9.294 9.504 9.694

11.750 11.750 — — — — — — — 11.750 11.750 — — 11.750 — — — — — — — — — — 11.750 11.750 — — — — — — — — — — — — — — — — — — — — —

9.694 9.604 — — — — — — — 9.694 9.604 — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

11.460 11.460 — — — — — — — 11.460 11.460 — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

3,100 3,950 3,400 4,160 5,460 6,760 8,760 10,370 12,010 3,490 4,300 5,590 6,960 650 4,460 7,550 5,950 8,640 9,600 4,460 5,950 9,600 7,550 8,640 — 1,420 2,100 3,130 4,420 5,220 4,460 5,950 7,550 8,640 2,100 3,130 4,460 5,950 7,550 8,640 4,460 5,950 7,550 8,640 9,600 7,550 4,460


Page 39 NO. 203


Round Thread Short

Long

Buttress Thd.



Ext. Line t

9,970 10,520 15,510 12,180 13,840 10,520

— — — — — —

9,970 10,520 15,510 12,180 13,840 10,520

9,940 10,490 15,460 12,140 13,800 10,490

1,635 1,725 2,543 1,998 2,270 1,725

— — — — — —

1,096 1,109 1,622 1,294 1,451 1,123

1,304 1,344 1,942 1,584 1,743 1,385

— — — — — —

5,490 6,040 6,590 7,250 7,980 8,720 9,850 10,750 11,680 6,960 7,660 8,430 9,200 — 6,590 7,980 7,250 8,720 9,520 6,960 7,660 10,050 8,430 9,200 1,820 2,280 3,130 3,580 4,030 4,430 5,860 6,450 7,100 7,750 4,560 5,210 5,860 6,450 7,100 7,750 8,060 8,860 9,760 10,650 11,640 11,090 9,160

5,490 6,040 6,590 7,250 7,980 8,720 — — — 6,960 7,660 8,430 9,200 1,140 6,590 7,980 7,250 8,720 9,200 6,960 7,660 9,710 8,430 9,200 1,820 2,280 3,130 3,580 4,030 4,430 5,860 6,450 7,100 7,750 4,560 5,210 5,860 6,450 7,100 7,750 8,060 8,860 9,760 10,650 11,240 11,090 9,160

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

5,490 6,040 6,590 7,250 7,980 8,720 — — — 6,960 7,660 8,430 9,200 — 6,590 7,980 7,250 8,720 8,980 6,960 7,660 9,480 8,430 9,200 — — 3,130 3,580 4,030 4,430 5,860 6,450 7,100 7,750 4,560 5,210 5,860 6,450 7,100 7,750 8,060 8,860 9,760 10,650 10,980 11,090 9,160

1,092 1,196 1,311 1,435 1,573 1,708 1,915 2,079 2,243 1,383 1,515 1,660 1,803 229 1,311 1,573 1,435 1,708 1,856 1,383 1,515 1,959 1,660 1,803 367 457 629 715 801 877 1,165 1,276 1,398 1,519 915 1,040 1,165 1,276 1,398 1,519 1,602 1,754 1,922 2,088 2,269 2,184 1,820

756 843 879 979 1,089 1,198 — — — 927 1,032 1,148 1,263 196 916 1,136 1,021 1,249 1,317 927 1,032 1,388 1,148 1,263 205 314 562 659 756 843 906 1,010 1,123 1,236 681 799 916 1,021 1,136 1,249 1,080 1,203 1,338 1,472 1,618 1,503 1,213

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

1,160 1,271 1,287 1,409 1,544 1,677 — — — 1,354 1,483 1,625 1,765 — 1,316 1,579 1,441 1,716 1,822 1,354 1,483 1,918 1,625 1,765 — — 911 1,037 1,160 1,271 1,316 1,441 1,579 1,716 1,034 1,175 1,316 1,441 1,579 1,716 1,594 1,745 1,912 2,077 2,257 2,109 1,758

1,383 1,515 — — — — — — — 1,529 1,675 — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —



Page 40 TABLE


103/4

Grade

HCQ-125ª HCQ-125ª J-55 J-55 J-55 K-55 K-55 K-55 L-80 L-80 L-80ª L-80ª LS-140ª LS-140ª LS-140ª LS-140ª LS-140ª LS-65 LS-65 LS-65ª LS-65ª N-80 N-80 N-80 N-80ª N-80ª P-110 P-110 P-110 P-110 P-110* Q-125 Q-125 Q-125ª Q-125ª Q-125ª S-95 S-95 S-95ª S-95ª S-95ª T-95 T-95 T-95 T-95 T-95 T-95 T-95 V-150* V-150*

Thread & lg.


Inside Dia. In.

55.50 65.70 40.50 45.50 51.00 40.50 45.50 51.00 51.00 60.70 55.50 65.70 51.00 55.50 60.70 65.70 71.10 51.00 45.50 40.50 55.50 45.50 51.00 55.50 60.70 65.70 51.00 55.50 60.70 65.70 71.10 51.00 60.70 55.50 65.70 71.10 60.70 65.70 51.00 55.50 71.10 51.00 55.50 60.70 65.70 73.20 79.20 85.30 65.70 71.10

9.760 9.560 10.050 9.950 9.850 10.050 9.950 9.850 9.850 9.660 9.760 9.560 9.850 9.760 9.660 9.560 9.450 9.850 9.950 10.050 9.760 9.950 9.850 9.760 9.660 9.560 9.850 9.760 9.660 9.560 9.450 9.850 9.660 9.760 9.560 9.450 9.660 9.560 9.850 9.760 9.450 9.850 9.760 9.660 9.560 9.406 9.282 9.156 9.560 9.450

Drift Dia. In.

O.D. of lg. In.

9.604 9.404 9.894 9.794 9.694 9.894 9.794 9.694 9.694 9.504 9.604 9.404 9.694 9.604 9.504 9.404 9.294 9.694 9.794 9.894 9.604 9.875 9.694 9.604 9.504 9.404 9.694 9.604 9.504 9.404 9.294 9.694 9.504 9.604 9.404 9.294 9.504 9.404 9.694 9.604 9.294 9.694 9.604 9.504 9.404 9.250 9.126 9.000 9.404 9.294

— — 11.750 11.750 11.750 11.750 11.750 11.750 — — — — — — — — — — — — — — 11.750 11.750 — — 11.750 11.750 11.750 11.750 11.750 — — — — — — — — — — — — — — — — — 11.750 11.750


— — — 9.794 9.694 — 9.794 9.694 — — — — — — — — — — — — — — 9.694 9.604 — — 9.694 9.604 9.504 — — — — — — — — — — — — — — — — — — — — —

O.D. of Box In.

— — — 11.460 11.460 — 11.460 11.460 — — — — — — — — — — — — — — 11.460 11.460 — — 11.460 11.460 11.460 — — — — — — — — — — — — — — — — — — — — —


5,950 8,640 1,580 2,090 2,700 1,580 2,090 2,700 3,220 5,160 4,020 6,300 4,460 5,950 7,550 8,640 10,570 2,870 2,280 1,680 3,690 2,470 3,220 4,020 5,160 6,300 3,670 4,630 5,860 7,490 9,280 3,740 6,070 4,850 7,920 9,990 7,550 8,640 4,460 5,950 9,600 3,480 4,290 5,590 6,960 9,090 10,800 12,540 8,330 10,890


Page 41 NO. 203


10,070 12,110 3,130 3,580 4,030 3,130 3,580 4,030 5,860 7,100 6,450 7,750 10,260 11,280 12,420 13,560 14,810 4,760 4,230 3,700 5,240 5,210 5,860 6,450 7,100 7,750 8,060 8,860 9,760 10,650 — 9,160 11,090 10,070 12,110 13,230 8,430 9,200 6,960 7,660 10,050 6,960 7,660 8,430 9,200 10,390 11,350 12,330 — —

Round Thread Short

10,070 12,110 3,130 3,580 4,030 3,130 3,580 4,030 5,860 7,100 6,450 7,750 10,260 11,280 12,420 13,560 14,310 4,760 4,230 3,700 5,240 5,210 5,860 6,450 7,100 7,750 8,060 8,860 9,760 10,650 11,240 9,160 11,090 10,070 12,110 12,780 8,430 9,200 6,960 7,660 9,710 6,960 7,660 8,430 9,200 — — — 14,530 15,330


Long

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

Buttress Thd.

10,070 12,110 3,130 3,580 4,030 3,130 3,580 4,030 5,860 7,100 6,450 7,750 10,260 11,280 12,420 13,560 13,980 4,760 4,230 3,700 5,240 5,210 5,860 6,450 7,100 7,750 8,060 8,860 9,760 10,650 10,980 9,160 11,090 10,070 12,110 12,480 8,430 9,200 6,960 7,660 9,480 6,960 7,660 8,430 9,200 — — — 14,530 14,970

t Strength - 1000 Lbs.**


Threaded & lg. t ButRound Thread tress Short Long Thd.

1,993 2,373 629 715 801 629 715 801 1,165 1,398 1,276 1,519 2,039 2,233 2,446 2,657 2,888 946 845 743 877 1,040 1,165 1,276 1,398 1,519 1,602 1,754 1,922 2,088 2,269 1,820 2,184 1,993 2,373 2,578 1,660 1,803 1,383 1,515 1,959 1,383 1,515 1,660 1,803 2,021 2,194 2,367 2,847 3,094

1,351 1,653 420 493 565 450 528 606 794 983 884 1,082 1,356 1,510 1,680 1,848 2,031 661 576 491 736 701 804 895 996 1,096 1,080 1,203 1,338 1,472 1,618 1,213 1,503 1,351 1,653 1,817 1,161 1,277 937 1,043 1,403 927 1,032 1,148 1,263 — — — 1,978 2,174


— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

1,925 2,291 700 796 891 819 931 1,043 1,190 1,428 1,303 1,551 1,959 2,146 2,351 2,554 2,775 1,026 916 806 1,124 1,097 1,228 1,345 1,473 1,600 1,594 1,745 1,912 2,077 2,418 1,758 2,109 1,925 2,291 2,489 1,670 1,814 1,392 1,524 1,971 1,354 1,483 1,625 1,765 — — — 2,799 2,957

Ext. Line t

— — — 975 1,092 — 1,236 1,383 — — — — — — — — — — — — — — 1,456 1,595 — 1,820 1,993 2,000 — — — — — — — — — — — — — — — — — — — — —

Page 42 TABLE


Grade

Extreme Line

Thread & lg.


Inside Dia. In.

Drift Dia. In.

O.D. of lg. In.

Drift Dia. In.

O.D. of Box In.


113/4

C-75 C-90 C-95 F-25* H2S-90ª H2S-90ª H2S-90ª H2S-95 H2S-95ª H2S-95ª H-40 HCK-55ª HCK-55ª HCK-55ª HCL-80ª HCL-80ª HCN-80ª HCN-80ª H-110ª H-110ª H-110ª HCQ-125ª HCQ-125ª HCQ-125ª J-55 J-55 J-55 K-55 K-55 K-55 L-80 L-80ª LS-140 LS-140ª LS-65 LS-65ª LS-65ª LS-65ª N-80 N-80ª P-110ª P-110ª Q-125ª Q-125ª Q-125ª S-95 S-95 S-95ª T-95

60.00 60.00 60.00 38.00 60.00 65.00 71.00 65.00 60.00 71.00 42.00 47.00 54.00 60.00 60.00 65.00 60.00 65.00 60.00 65.00 71.00 60.00 65.00 71.00 47.00 54.00 60.00 47.00 54.00 60.00 65.00 60.00 71.00 65.00 65.00 47.00 54.00 60.00 60.00 65.00 65.00 71.00 60.00 65.00 71.00 60.00 71.00 65.00 60.00

10.772 10.772 10.772 11.150 10.772 10.682 10.586 10.682 10.772 10.586 11.084 11.000 10.880 10.772 10.772 10.682 10.772 10.682 10.772 10.682 10.586 10.772 10.682 10.586 11.000 10.880 10.772 11.000 10.880 10.772 10.682 10.772 10.586 10.682 10.682 11.000 10.880 10.772 10.772 10.682 10.682 10.586 10.772 10.682 10.586 10.772 10.586 10.682 10.772

10.616 10.616 10.616 10.994 10.616 10.526 10.430 10.526 10.616 10.430 10.928 10.844 10.724 10.616 10.616 10.526 10.616 10.526 10.616 10.526 10.430 10.616 10.526 10.430 10.844 10.724 10.616 10.844 10.724 10.616 10.526 10.616 10.430 10.526 10.526 10.844 10.724 10.616 10.616 10.625 10.526 10.430 10.616 10.526 10.430 10.616 10.430 10.526 10.616

12.750 — 12.750 12.750 — — — — — — 12.750 — — — — — — — — — — — — — 12.750 12.750 12.750 12.750 12.750 12.750 — — — — — — — — 12.750 — — — — — — — — — —

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

3,070 3,360 3,440 620 4,410 5,140 7,280 5,740 4,410 7,280 1,070 2,000 3,100 4,360 4,410 5,740 4,410 5,740 4,410 5,740 7,280 4,410 5,740 7,280 1,510 2,070 2,660 1,510 2,070 2,660 3,870 3,180 7,280 5,740 3,580 1,590 2,250 2,840 3,180 3,870 4,480 5,470 3,680 4,690 5,760 4,410 7,280 5,740 3,440

117/8

H2S-90 H2S-95ª H-110ª HCQ-125ª

71.80 71.80 71.80 71.80

10.711 10.711 10.711 10.711

— — — —

— — — —

— — — —

— — — —

7,190 7,190 7,190 7,190


Page 43 NO. 203


Round Thread Short

Long

Buttress Thd.




Ext. Line t

5,460 6,550 6,920 — 6,550 7,160 7,800 7,560 6,920 8,230 1,980 3,070 3,560 4,010 5,830 6,360 5,830 6,360 8,010 8,750 9,530 9,100 9,940 10,840 3,070 3,560 4,010 3,070 3,560 4,010 6,360 5,830 12,140 11,130 5,170 3,630 4,210 4,730 5,830 6,360 8,750 9,530 9,100 9,940 10,840 6,920 8,230 7,560 6,920

5,460 6,550 6,920 1,120 6,550 7,160 7,800 7,560 6,920 8,230 1,980 3,070 3,560 4,010 5,830 6,360 5,830 6,360 8,010 8,750 9,530 9,100 9,940 10,840 3,070 3,560 4,010 3,070 3,560 4,010 6,360 5,830 12,140 11,130 5,170 3,630 4,210 4,730 5,830 6,360 8,750 9,530 9,100 9,940 10,840 6,920 8,230 7,560 6,920

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

5,460 6,550 6,920 — 6,550 7,160 7,800 7,560 6,920 8,230 — 3,070 3,560 4,010 5,830 6,360 5,830 6,360 8,010 8,750 9,530 9,100 9,940 10,840 3,070 3,560 4,010 3,070 3,560 4,010 6,360 5,830 12,140 11,130 5,170 3,630 4,210 4,730 5,830 6,360 8,750 9,530 9,100 9,940 10,840 6,920 8,230 7,560 6,920

1,298 1,557 1,644 270 1,557 1,639 1,838 1,788 1,644 1,940 478 737 850 952 1,384 1,505 1,384 1,505 1,903 2,070 2,246 2,163 2,352 2,552 737 850 952 737 850 952 1,505 1,384 2,859 2,634 1,223 871 1,005 1,125 1,384 1,505 2,070 2,246 2,163 2,352 2,552 1,644 1,940 1,788 1,644

869 1,011 1,066 222 1,055 1,164 1,226 1,177 1,066 1,293 307 638 760 869 1,055 1,152 1,055 1,164 1,242 1,371 1,506 1,396 1,540 1,693 477 568 649 509 606 693 1,007 913 1,893 1,722 837 557 665 759 924 1,019 1,371 1,506 1,396 1,540 1,693 1,077 1,306 1,189 1,066

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

1,361 1,517 1,596 — 1,555 1,691 1,790 1,736 1,596 1,884 — 1,054 1,216 1,361 1,555 1,691 1,555 1,691 1,877 2,041 2,215 2,074 2,256 2,448 807 931 1,042 935 1,079 1,208 1,521 1,399 2,730 2,516 1,307 931 1,074 1,201 1 440 1,566 2,041 2,215 2,074 2,256 2,448 1,638 1,933 1,781 1,596

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

7,270 8,150 9,430 10,720

7,270 8,150 9,430 10,720

— — — —

7,270 8,150 9,430 10,720

1,858 1,962 2,271 2,581

1,129 1,141 1,329 1,494

— — — —

1,647 1,691 1,988 2,198

— — — —



Page 44 TABLE


Thread & lg.

Grade


Inside Dia. In.

117/8

LS-140ª P-110ª Q-125ª S-95

71.80 71.80 71.80 71.80

10.711 10.711 10.711 10.711

— — — —

— — — —

— — — —

— — — —

7,190 5,290 5,630 7,190

133/8

C-75 C-75* C-75* C-75* C-90 C-90 C-95 C-95 F-25* H2S-90 H2S-90 H2S-95 H2S-95 H-40 HCK-55ª HCK-55ª HCK-55ª HCL-80ª HCL-80ª HCN-80ª HCN-80ª H-110ª H-110ª H-110ª H-110ª HCQ-125ª HCQ-125ª HCQ-125ª J-55 J-55 J-55 K-55 K-55 K-55 L-80 L-80ª LS-140ª LS-65 LS-65 LS-65ª LS-65ª N-80 N-80 N-80* N-80* N-80ª P-110* P-110ª P-110ª

72.00 77.00 85.00 98.00 68.00 72.00 68.00 72.00 48.00 72.00 80.70 72.00 80.70 48.00 54.50 61.00 68.00 68.00 72.00 68.00 72.00 68.00 72.00 80.70 86.00 72.00 80.70 86.00 54.50 61.00 68.00 54.50 61.00 68.00 72.00 68.00 72.00 54.50 68.00 61.00 72.00 72.00 85.00 77.00 98.00 68.00 72.00 68.00 80.70

12.347 12.275 12.159 11.937 12.415 12.347 12.415 12.347 12.715 12.347 12.215 12.347 12.215 12.715 12.615 12.515 12.415 12.415 12.347 12.415 12.347 12.415 12.347 12.215 12.125 12.347 12.215 12.125 12.615 12.515 12.415 12.615 12.515 12.415 12.347 12.415 12.347 12.615 12.415 12.515 12.347 12.347 12.159 12.275 11.937 12.415 12.347 12.415 12.215

12.191 12.119 12.003 11.781 12.259 12.191 12.259 12.191 12.559 12.191 12.059 12.191 12.059 12.559 12.459 12.359 12.259 12.259 12.191 12.259 12.191 12.259 12.191 12.059 11.969 12.191 12.059 11.969 12.459 12.359 12.259 12.459 12.359 12.259 12.191 12.259 12.191 12.459 12.259 12.359 12.191 12.191 12.003 12.119 11.781 12.259 12.191 12.259 12.059

14.375 14.375 14.375 14.375 — — — 14.375 14.375 — — — — 14.375 — — — — — — — — — — — — — — 14.375 14.375 14.375 14.375 14.375 14.375 — — — — — — — 14.375 14.375 14.375 14.375 — 14.375 — —

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

2,590 2,990 3,810 5,720 2,320 2,780 2,330 2,820 560 3,470 4,990 3,470 4,990 770 1,400 2,040 2,850 2,910 3,470 2,910 3,470 2,910 3,470 4,990 6,240 3,470 4,990 6,240 1,130 1,540 1,950 1,130 1,540 1,950 2,670 2,260 3,470 1,140 2,110 1,620 2,430 2,670 3,870 3,100 5,910 2,260 2,880 2,340 4,000

Size O.D. In.

Drift Dia. In.

O.D. of lg. In.

Drift Dia. In.

O.D. of Box In.



Page 45 NO. 203


Round Thread Short

Long

Buttress Thd.




Ext. Line t

12,010 9,430 10,720 8,150

12,010 9,430 10,720 8,150

— — — —

12,010 9,430 10,720 8,150

2,891 2,271 2,581 1,962

1,671 1,329 1,494 1,153

— — — —

2,451 1,988 2,198 1,735

— — — —

5,040 — — — 5,650 6,050 5,970 6,390 — 6,050 6,830 6,390 7,210 1,730 2,730 3,090 3,450 5,020 5,380 5,020 5,380 6,910 7,400 8,350 9,000 8,410 9,490 10,220 2,730 3,090 3,450 2,730 3,090 3,450 5,380 5,020 9,420 3,230 4,080 3,660 4,370 5,380 — — — 5,020 — 6,910 8,350

5,040 5,400 5,970 6,270 5,650 6,050 5,970 6,390 1,080 6,050 — 6,390 — 1,730 2,730 3,090 3,450 5,020 5,380 5,020 5,380 6,910 7,400 — — 8,410 — — 2,730 3,090 3,450 2,730 3,090 3,450 5,380 5,020 9,420 3,230 4,080 3,660 4,370 5,380 6,360 5,760 6,680 5,020 7,400 6,910 —

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

5,040 5,400 5,970 6,120 5,650 6,050 5,970 6,390 — 6,050 7,340 6,390 7,210 — 2,730 3,090 3,450 5,020 5,380 5,020 5,380 6,910 7,400 8,350 9,000 8,410 9,490 10,220 2,730 3,090 3,450 2,730 3,090 3,450 5,380 5,020 9,420 3,230 4,080 3,660 4,370 5,380 6,360 5,760 6,530 5,020 7,400 6,910 8,350

1,558 1,662 1,829 2,144 1,750 1,869 1,847 1,973 338 1,869 2,098 1,973 2,215 541 853 962 1,069 1,556 1,661 1,556 1,661 2,139 2,284 2,565 2,754 2,596 2,914 3,129 853 962 1,069 853 962 1,069 1,661 1,556 2,908 1,008 1,264 1,137 1,350 1,661 1,951 1,773 2,287 1,556 2,596 2,139 2,565

978 1,054 1,177 1,408 1,057 1,142 1,114 1,204 260 1,192 — 1,204 — 322 689 798 905 1,093 1,181 1,103 1,192 1,297 1,402 — — 1,577 — — 514 595 675 547 633 718 1,029 952 1,763 602 791 697 854 1,040 1,252 1,122 1,498 963 1,402 1,297 —

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

1,598 2,054 2,261 2,296 1,683 1,798 1,772 1,893 — 1,850 2,077 1,893 2,125 — 1,194 1,345 1,496 1,732 1,850 1,732 1,850 2,079 2,221 2,493 2,677 2,463 2,765 2,969 909 1,025 1,140 1,038 1,169 1,300 1,650 1,545 2,749 1,052 1,318 1,185 1,408 1,693 2,364 2,148 2,400 1,585 2,433 2,079 2,493

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —



Page 46 TABLE


Thread & lg.

Grade


Inside Dia. In.

133/8

P-110ª Q-125ª Q-125ª Q-125ª S-95 S-95ª S-95ª S-95ª T-95 T-95 V-150*

86.00 72.00 80.70 86.00 72.00 68.00 80.70 86.00 68.00 72.00 72.00

12.125 12.347 12.215 12.125 12.347 12.415 12.215 12.125 12.415 12.347 12.347

11.969 12.191 12.059 11.969 12.191 12.259 12.059 11.969 12.259 12.191 12.191

— — — — — — — — — — 14.375

— — — — — — — — — — —

— — — — — — — — — — —

4,780 2,880 4,140 5,030 3,470 2,910 4,990 6,240 2,330 2,820 2,880

131/2

H2S-90 H2S-95 H-110ª HCQ-125ª P-110ª Q-125ª S-95ª

81.40 81.40 81.40 81.40 81.40 81.40 81.40

12.340 12.340 12.340 12.340 12.340 12.340 12.340

— — — — — — —

— — — — — — —

— — — — — — —

— — — — — — —

4,860 4,860 4,860 4,860 3,910 4,030 4,860

135/8

H2S-90ª H2S-95ª H-110ª HCQ-125ª P-110ª Q-125ª S-95ª

88.20 88.20 88.20 88.20 88.20 88.20 88.20

12.375 12.375 12.375 12.375 12.375 12.375 12.375

— — — — — — —

— — — — — — —

— — — — — — —

— — — — — — —

5,930 5,930 5,930 5,930 4,570 4,800 5,930

16

C-75* F-25* H-40 HCN-80ª HCN-80ª HCN-80ª H-110ª H-110ª H-110ª HCQ-125ª HCQ-125ª HCQ-125ª J-55 J-55 J-55 J-55 K-55 K-55 K-55 K-55* LS-65ª LS-65ª N-80 N-80* N-80ª N-80ª

109.00 55.00 65.00 84.00 95.00 97.00 84.00 95.00 97.00 84.00 95.00 97.00 75.00 84.00 109.00 118.00 75.00 84.00 118.00 109.00 75.00 84.00 118.00 109.00 84.00 95.00

14.688 15.376 15.250 15.010 14.868 14.850 15.010 14.868 14.850 15.010 14.868 14.850 15.124 15.010 14.688 14.570 15.124 15.010 14.570 14.688 15.124 15.010 14.570 14.688 15.010 14.868

14.500 15.188 15.062 14.822 — — 14.822 — — 14.822 — — 14.936 14.822 14.500 14.382 14.936 14.822 14.382 14.500 14.936 14.822 14.382 14.500 14.822 —

17.000 17.000 17.000 — — — — — — — — — 17.000 17.000 — — 17.000 17.000 — 17.000 — — — 17.000 — —

— — — — — — — — — — — — — — — — — — — — — — — — — —

— — — — — — — — — — — — — — — — — — — — — — — — — —

2,980 290 670 1,910 2,580 2,990 1,910 2,580 2,990 1,910 2,580 2,990 1,020 1,410 2,560 3,170 1,020 1,410 3,170 2,560 1,020 1,470 3,680 3,080 1,480 2,180

Size O.D. In.

Drift Dia. In.

O.D. of lg. In.

Drift Dia. In.

O.D. of Box In.



Page 47 NO. 203


Round Thread Short

Long

Buttress Thd.




Ext. Line t

9,000 8,410 9,490 10,220 6,390 5,970 7,210 7,770 5,970 6,390 —

— 8,410 — — 6,390 5,970 — — 5,970 6,390 10,090

— — — — — — — — — — —

9,000 8,410 9,490 10,220 6,390 5,970 7,210 7,770 5,970 6,390 10,090

2,754 2,596 2,914 3,129 1,973 1,847 2,215 2,378 1,847 1,973 3,323

— 1,577 — — 1,215 1,125 — — 1,114 1,204 1,887

— — — — — — — — — — —

2,677 2,463 2,765 2,969 1,935 1,812 2,173 2,333 1,772 1,893 2,976

— — — — — — — — — — —

6,770 7,140 8,270 9,400 8,270 9,400 7,140

— — — — — — —

— — — — — — —

6,770 7,140 8,270 9,400 8,270 9,400 7,140

2,119 2,236 2,590 2,943 2,590 2,943 2,236

— — — — — — —

— — — — — — —

1,862 1,905 2,235 2,479 2,235 2,479 1,948

— — — — — — —

7,220 7,630 8,830 10,030 8,830 10,030 7,630

— — — — — — —

— — — — — — —

7,220 7,630 8,830 10,030 8,830 10,030 7,630

2,297 2,425 2,808 3,191 2,808 3,191 2,425

— — — — — — —

— — — — — — —

1,801 1,843 2,163 2,399 2,163 2,399 1,885

— — — — — — —

— — 1,640 4,330 4,950 5,030 5,960 6,810 6,920 6,770 7,740 7,860 2,630 2,980 3,950 4,300 2,630 2,980 4,300 — 3,110 3,520 6,260 — 4,330 4,950

5,380 850 1,640 4,330 — — 5,960 — — 6,770 — — 2,630 2,980 3,950 4,300 2,630 2,980 4,300 3,950 3,110 3,520 6,260 5,740 4,330 —

— — — — — — — — — — — — — — — — — — — — — — — — — —

— — — 4,330 4,950 5,030 5,960 6,810 6,920 6,770 7,740 7,860 2,630 2,980 3,950 4,300 2,630 2,980 4,300 3,950 3,110 3,520 6,260 — 4,330 4,950

2,372 384 736 1,929 2,196 2,230 2,652 3,019 3,067 3,014 3,431 3,485 1,178 1,326 1,739 1,889 1,178 1,326 1,889 1,739 1,392 1,567 2,747 2,530 1,929 2,196

1,499 258 439 1,342 — — 1,575 — — 1,773 — — 710 817 1,116 1,224 752 865 1,296 1,181 832 957 1,741 1,594 1,167 —

— — — — — — — — — — — — — — — — — — — — — — — — — —

— — — 1,898 2,161 2,194 2,518 2,866 2,910 2,809 3,198 3,246 1,200 1,351 1,772 1,924 1,331 1,499 2,131 1,962 1,394 1,570 2,703 — 1,898 2,161

— — — — — — — — — — — — — — — — — — — — — — — — — —



Page 48 TABLE


Thread & lg.

Grade


Inside Dia. In.

16

N-80ª P-110ª P-110ª P-110ª Q-125ª Q-125ª Q-125ª

97.00 84.00 95.00 97.00 84.00 95.00 97.00

14.850 15.010 14.868 14.850 15.010 14.868 14.850

— 14.822 — — 14.822 — —

— — — — — — —

— — — — — — —

— — — — — — —

2,270 1,480 2,230 2,340 1,480 2,230 2,340

185/8

H-40 H-40 H-40 H-40ª J-55 J-55 J-55 J-55ª K-55 K-55 K-55 K-55 N-80 N-80 N-80 N-80

87.50 106.00 117.50 94.50 87.50 106.00 117.50 94.50 87.50 94.50 106.00 117.50 87.50 94.50 106.00 117.50

17.755 17.563 17.439 17.689 17.755 17.563 17.439 17.689 17.755 17.689 17.563 17.439 17.755 17.689 17.563 17.439

17.567 17.375 17.251 17.501 17.567 17.375 17.251 17.501 17.567 17.501 17.375 17.251 17.567 17.501 17.375 17.251

19.625 — — — 19.625 — — — 19.625 — — — — — — —

— — — — — — — — — — — — — — — —

— — — — — — — — — — — — — — — —

630 1,140 1,500 780 630 1,140 1,510 780 630 780 1,140 1,510 630 780 1,150 1,620

20

F-25* H-40 J-55 J-55 J-55 K-55 K-55 K-55 K-55 L-80 N-80 N-80

94.00 94.00 94.00 106.50 133.00 94.00 106.50 133.00 169.00 169.00 106.50 133.00

19.124 19.124 19.124 19.000 18.730 19.124 19.000 18.730 18.376 18.376 19.000 18.730

18.936 18.936 18.936 18.812 18.542 18.936 18.812 18.542 18.188 18.188 18.812 18.542

21.000 21.000 21.000 21.000 21.000 21.000 21.000 21.000 — — — —

— — — — — — — — — — — —

— — — — — — — — — — — —

410 520 520 770 1,500 520 770 1,500 2,500 3,020 770 1,600

Size O.D. In.

Drift Dia. In.

O.D. of lg. In.

Drift Dia. In.

O.D. of Box In.



Page 49 NO. 203


Round Thread Short

Long

Buttress Thd.




Ext. Line t

5,030 5,960 6,810 6,920 6,770 7,740 7,860

— 5,960 — — 6,770 — —

— — — — — — —

5,030 5,960 6,810 6,920 6,770 7,740 7,860

2,230 2,652 3,019 3,067 3,014 3,431 3,485

— 1,575 — — 1,773 — —

— — — — — — —

2,194 2,518 2,866 2,910 2,809 3,198 3,246

— — — — — — —

1,630 2,000 2,230 1,760 2,250 2,740 3,060 2,420 2,250 2,420 2,740 3,060 3,270 3,520 3,990 4,460

1,630 2,000 2,230 1,760 2,250 2,740 3,060 2,420 2,250 2,420 2,740 3,060 3,270 3,520 3,990 4,460

— — — — — — — — — — — — — — — —

— 2,000 2,230 1,760 — 2,740 3,060 2,420 — 2,420 2,740 3,060 3,270 3,520 3,990 4,460

994 1,208 1,344 1,068 1,367 1,661 1,849 1,469 1,367 1,469 1,661 1,849 1,990 2,137 2,416 2,689

559 703 795 609 754 948 1,072 821 794 865 998 1,129 1,079 1,174 1,356 1,534

— — — — — — — — — — — — — — — —

— 1,206 1,342 1,067 1,329 1,613 1,795 1,427 1,427 1,533 1,733 1,929 1,887 2,027 2,292 2,551

— — — — — — — — — — — — — — — —

— 1,530 2,110 2,410 3,060 2,110 2,410 3,060 3,910 5,680 3,500 4,450

960 1,530 2,110 2,410 3,060 2,110 2,410 3,060 3,230 4,690 3,500 4,450

— — 2,110 2,410 3,060 2,110 2,410 3,060 3,430 4,990 3,500 4,450

— — — — — — — — 3,380 4,920 3,500 4,450

673 1,077 1,480 1,685 2,125 1,480 1,685 2,125 2,692 3,916 2,450 3,091

359 581 784 913 1,192 824 960 1,253 1,402 2,202 1,307 1,707

— — 907 1,057 1,380 955 1,113 1,453 1,732 2,549 1,514 1,976

— — 1,402 1,596 2,012 1,479 1,683 2,123 2,689 3,610 2,281 2,877

— — — — — — — — — — — —



Page 50 TABLE 204

STRETCH DATA FOR DRILL PIPE, TUBING AND CASING Size of Tubing, D.P. or Casing

2.375” Upset Tubing 4.70 #/Ft.



2.875” Drill Pipe 10.40 #/Ft.

Stretch Per Length of Pipe Suspended in Well, Feet

Pull Above 1000 Lb. Pull Above Wt. of Pipe, Inches Factor C

500 1,000 2,000 3,000

.115 .310 .620 .930

4,000 5,000 10,000

1.240 1.550 3.100

500 1,000 2,000 3,000

Stretch Weight of Pipe Per In. Stretch of Pipe Pounds

6,450 3,225 1,612 1,075

.14 .56 2.22 5.00

806 644 322

8.88 13.88 55.51

.110 .220 .440 .660

9,080 4,540 2,270 1,513

.14 .56 2.22 5.00

4,000 5,000 10,000

.880 1.100 2.200

1,135 908 454

8.88 13.88 55.51

500 1,000 2,000 3,000

.0772 .1544 .3088 .4632

12,960 6,480 3,240 2,160

.14 .56 2.22 5.00

4,000 5,000 10,000

.6176 .7720 1.544

1,620 1,296 648

8.88 13.88 55.51

500 1,000 2,000 3,000

.070 .140 .280 .420

14,300 7,150 3,575 2,383

.14 .56 2.22 5.00

4,000 5,000 10,000

.560 .700 1.40

1,787 1,430 715

8.88 13.88 55.51

FORMULA FOR DETERMINING STRETCH IN PIPE S=

L X P X C 1000 X 1000

(use to set tension packer with no weight indication) FORMULA FOR DETERMINING PULL OF PIPE 1000 X 1000 X S P= C X L FORMULA FOR FREE PIPE DEPTH L= Where:

L S P C

= = = =

Due To Own Weight Suspended in Water, Inches

S X 1000 X 1000 P

X

C

Length of free pipe in feet. Stretch pulled in pipe, in inches. Pull on pipe to get the stretch “S” in pounds Constant for given pipe size and weight being stretched. (For this equation use C factor at pipe length of 1000 ft.)

Page 51 TABLE 204

STRETCH DATA FOR DRILL PIPE, TUBING AND CASING Size of Tubing, D.P. or Casing

Stretch Per Length of Pipe Suspended in Well, Feet

3.500” Drill Pipe 13.30 #/Ft.

4.500” Drill Pipe 16.60 #/Ft.

5.500” Casing 17 #/Ft.

7.000” Casing 23 #/Ft.

Pull Above 1000 Lb. Pull Above Wt. of Pipe, Inches Factor C

Stretch Weight of Pipe Per In. Stretch of Pipe Pounds

Due To Own Weight Suspended in Water, Inches

500 1,000 2,000 3,000

.055 .110 .220 .330

18,200 9,100 4,550 3,033

.14 .56 2.22 5.00

4,000 5,000 10,000

.440 .550 1.10

2,275 1,820 910

8.88 13.88 55.51

500 1,000 2,000 3,000

.0450 .0900 .180 .270

22,200 11,100 5,550 3,700

.14 .56 2.22 5.00

4,000 5,000 10,000

.360 .450 .900

2,775 2,220 1,110

8.88 13.88 55.51

500 1,000 2,000 3,000

.0402 .0804 .160 240

24,800 12,400 6,230 4,133

.14 .56 2.22 5.00

4,000 5,000 10,000

.320 .402 804

3,100 2,480 1,240

8.88 13.88 55.51

500 1,000 2,000 3,000

.0301 .0602 .120 .181

33,220 16,610 8,305 5,537

.14 .56 2.22 5.00

4,000 5,000 10,000

241 .301 .602

4,152 3,322 1,661

8.88 13.88 55.51

NOTE: The above figures apply only to steel pipe that has not been stretched or is not being stretched beyond its elastic limit. Example: A 7” RTTS is set at 15,000 feet on 2 3/8: 4.7 #/ft. EUE tubing. There are indications that the casing has collapsed above the tool. Pick up pipe weight, mark pipe and pull 20,000 pounds above pipe weight. This 20,000 pounds stretches pipe 25 inches. Where is the casing collapsed? S = 25 inches P = 20,000 pounds C = .31 (C factor from table at 1000 ft.) L=

25 X 1000 X 1000 20,000 X .31

L = 4032 feet

Page 52 TABLE 205

SLACK-OFF DATA FOR TUBING AND DRILL PIPE Size of Tubing or Drill Pipe

Slack-Off Factor*

1.900 O.D. EUE Tubing 2.375 O.D. EUE Tubing 2.875 O.D. EUE Tubing 3.500 O.D. EUE Tubing 2.875 O.D. 10.40 lb/ft DP 3.500 O.D. 13.30 lb/ft DP 4.500 O.D. 16.60 lb/ft DP

0.68 0.39 0.26 0.17 0.16 0.12 0.10

* Inches to slack-off to obtain 1000 lbs. weight on packer for each 1000 ft. of depth. An allowance is included for coiling and friction. Required slack (inc.) =

Desired Weight 1000

X

Packer Depth 1000

X Factor

Example: Weight desired on packer ......................................... 15,000 lbs. Depth packer set ............................................................. 5,000:” Size of Tubing ........................................................ 2.375” EUE Slack-off factor for 2.375” EUE from table = 0.39 15,000 1000

X

5,000 1000

X 0.39 = 29.25 (use 29 inches)

The setting stroke required to set any particular tool is not included in these figures and will have to be added.

NOTE: The above figures apply only to pipe that has not been stretched, or is not being stretched beyond its elastic limit.

Page 53

TUBING

API Non-Upset Tubing Sizes: 1.050” - 41/2”

API External Upset Tubing Sizes: 1.050” - 41/2”

Extreme-Line Tubing Sizes: 23/8” - 31/2”

Page 54

CASING API SHORT OR LONG

Round-Thread Casing Sizes: 41/2” - 20” (21/2” and 241/2”)

API Buttress-Thread Casing Sizes: 41/2” - 20”

API Extreme-Line Casing Sizes: 5” - 103/4”

Halliburton Red Book Sec200 5q1sp

Overview 3e4r5l

More details w3441

Related Documents 3m3m1z

Halliburton Red Book Sec200 5q1sp

Halliburton-red-book-cementing-data.pdf 1o2u3a

Halliburton Red Book Cementing Data 6o2f7

Halliburton u572x

Halliburton 2014 3h5561

Softaware Halliburton 1p4p3m