Jis_b_08265_000_000_2010_cor_2_201312_e_ch 2z3v3u
This document was ed by and they confirmed that they have the permission to share it. If you are author or own the copyright of this book, please report to us by using this report form. Report 3b7i
Overview 3e4r5l
& View Jis_b_08265_000_000_2010_cor_2_201312_e_ch as PDF for free.
More details w3441
- Words: 3,074
- Pages: 11
JAPANESE INDUSTRIAL STANDARD JIS B 8265:2010 Construction of pressure vessel—General principles December, 2013 ERRATA (1/11)
Page
Position
32
Figure 11 e) (below the figure)
36
6.2, Table 2
Error
Correct
tw is the pipe thickness of schedule 160.
tw is the pipe thickness of schedule 160. Nominal diameter of the pipe fitting is 80A (DN80) or under.
Type of
Efficiency of welded ts ( )
Type of
ts
Percentage of applying the
ts
b) 20 ％
Percentage
of
applying
the
radiographic examination
radiographic examination a) 100 ％
Efficiency of welded ts ( )
a) 100 ％
c) Not
b) 20 ％
c) Not applied
applied B－1
1.00
0.95
0.70
B－1
1.00
0.95
0.70
B－2
0.90
0.85
0.65
B－2
0.90
0.85
0.65
－
－
0.60
B－3
－
－
0.60
B－3
L－1
－
－
0.55
L－1
－
－
0.55
0.50
L－2
－
－
0.50
0.45
L－3
－
－
0.45
L－2 L－3
－ －
－ －
NOTE: The efficiency of welded ts in the case of cylindrical shells apply to longitudinal and circumference ts. However, the calculated thickness of cylindrical shells applies to the longitudinal ts.
(continued)
B 8265:2010
Page 40 6.5 c)
Position 6.5 c)
ERRATA (2/11)
Error See below.
Correct See below.
Error: For the hub part of tube plates with hubs or flat end plates with hubs (only in the case of machining from plates), the ultrasonic examination of the whole volume of the hub part from the two directions, the radial and axial, of the hub shall be performed in accordance with JIS G 0801, and the judging criteria given in 1) and 2) below shall be satisfied. Correct: For the hub part of tube plates with hubs or flat end plates with hubs (only in the case of machining from plates), the ultrasonic examination of the whole volume of the hub part from the two directions, the radial and axial, of the hub shall be performed in accordance with JIS G 0801 before and after machining, and the judging criteria given in 1) and 2) below shall be satisfied.
Page 60
63
Position Table B.1 (continued) Type: JIS G 3127 Designation: SL5N590 Base metal class Table B.1 (continued) Type: JIS G 3452 Designation: SGP Fabrication method Table B.1 (continued) Type: JIS G 3454 Designation: STPG370 Fabrication method Table B.1 (continued) Type: JIS G 3454 Designation: STPG410 Fabrication method Table B.1 (continued) Type: JIS G 3456 Designation: STPT370 Fabrication method Table B.1 (continued) Type: JIS G 3456 Designation: STPT410 Fabrication method Table B.1 (continued) Type: JIS G 3457 Designation: STPY400 Fabrication method
Error 9B
Correct 11A
E B
W B
S E
S W
S E
S W
S E
S W
S E
S W
A
W
(continued)
B 8265:2010
Page 65
66
67
Position Table B.1 (continued) Type: JIS G 3460 Designation: STPL380 Fabrication method Table B.1 (continued) Type: JIS G 3461 Designation: STB340 Fabrication method Table B.1 (continued) Type: JIS G 3461 Designation: STB410 Fabrication method Table B.1 (continued) Type: JIS G 3461 Designation: STB510 Fabrication method Table B.1 (continued) Type: JIS G 3462 Designation: STBA12 Fabrication method Table B.1 (continued) Type: JIS G 3462 Designation: STBA13 Fabrication method Table B.1 (continued) Type: JIS G 3462 Designation: STBA20 Fabrication method Table B.1 (continued) Type: JIS G 3462 Designation: STBA22 Fabrication method Table B.1 (continued) Type: JIS G 3463 Designation: SUS329J4LTB Fabrication method Type: JIS G 3463 Designation: SUS329J4LTB Add the values in the right as the allowable tensile stress values for fabrication method W (added above), for temperatures 40 °C, 75 °C, 100 °C, 125 °C, 150 °C, 175 °C, 200 °C, 225 °C, 250 °C, 275 °C and 300 °C, respectively.
ERRATA (3/11)
Error S E
Correct S W
S, E E
S, W W
S, E E
S, W W
S, E E
S, W W
S, E E
S, W W
S, E E
S, W W
S, E E
S, W W
S, E E
S, W W
–
–
S W
132, 132, 131, 129, 128, 125, 123, 122, 120, 119, 119
(continued)
B 8265:2010
Page 68
77
Position Table B.1 (continued) Type: JIS G 3464 Designation: STBL380 Fabrication method Table B.1 (continued) NOTE 3
80
Table B.1 (continued) Note ah)
83
Table B.3 (continued) Type: JIS H 3300 Model: 1020 Quality class: O Specified minimum tensile strength Table B.3 (continued) Type: JIS H 3300 Model: 1201 Quality class: O Specified minimum tensile strength Table B.3 (continued) Type: JIS H 3300 Model: 1220 Quality class: O Specified minimum tensile strength Table B.3 (continued) Type: JIS H 3300 Model: 1020 Quality class: OL Specified minimum tensile strength
ERRATA (4/11)
Error S, E E
S : seamless pipes; E : electric resistance welded tubes; A : submerged arc welding tubes; W : automatic arc welding tubes or electric resistance welded tubes. The external pressure chart number in this row may be applied to JIS G 4051, JIS G 4303, and JIS G 4311, only when used for stiffening rings 205 [Outer diameter 4 mm or over up to and incl. 100 mm /Wall thickness 0.3 mm or over up to and incl. 30 mm] 205 [Outer diameter 4 mm or over up to and incl. 250 mm /Wall thickness 0.3 mm or over up to and incl. 30 mm] 205 [Outer diameter 4 mm or over up to and incl. 250 mm /Wall thickness 0.3 mm or over up to and incl. 30 mm] 205 [Outer diameter 4 mm or over up to and incl. 100 mm /Wall thickness 0.3 mm or over up to and incl. 30 mm]
Correct S,W W
S: seamless pipes ; B: forge-welded tubes ; W : electric resistance welded tubes; submerged arc welding tubes; automatic arc welding tubes or laser welding tubes. The external pressure chart number in this row may be applied only when used for stiffening rings
205 [Outer diameter 4 mm or over up to and incl. 100 mm /Wall thickness 0.25 mm or over up to and incl. 30 mm] 205 [Outer diameter 4 mm or over up to and incl. 250 mm /Wall thickness 0.25 mm or over up to and incl. 30 mm] 205 [Outer diameter 4 mm or over up to and incl. 250 mm /Wall thickness 0.25 mm or over up to and incl. 30 mm] 205 [Outer diameter 4 mm or over up to and incl. 100 mm /Wall thickness 0.25 mm or over up to and incl. 30 mm]
(continued)
B 8265:2010
Page 83
ERRATA (5/11)
Position Table B.3 (continued) Type: JIS H 3300 Model: 1201 Quality class: OL Specified minimum tensile strength Table B.3 (continued) Type: JIS H 3300 Model: 1220 Quality class: OL Specified minimum tensile strength
Error 205 [Outer diameter 4 mm or over up to and incl. 250 mm /Wall thickness 0.3 mm or over up to and incl. 30 mm] 205 [Outer diameter 4 mm or over up to and incl. 250 mm /Wall thickness 0.3 mm or over up to and incl. 30 mm]
Correct 205 [Outer diameter 4 mm or over up to and incl. 250 mm /Wall thickness 0.25 mm or over up to and incl. 30 mm] 205 [Outer diameter 4 mm or over up to and incl. 250 mm /Wall thickness 0.25 mm or over up to and incl. 30 mm]
Table B.3 (continued) Type: JIS H 3300 Model: 1020 Quality class: 1/2H Specified minimum tensile strength Table B.3 (continued) Type: JIS H 3300 Model: 1100 Quality class: 1/2H Specified minimum tensile strength Table B.3 (continued) Type: JIS H 3300 Model: 1201 Quality class: 1/2H Specified minimum tensile strength Table B.3 (continued) Type: JIS H 3300 Model: 1220 Quality class: 1/2H Specified minimum tensile strength Table B.3 (continued) Type: JIS H 3300 Model: 1565 Quality class: 1/2H Specified minimum tensile strength
245 [Outer diameter 4 mm or over up to and incl. 100 mm /Wall thickness 0.3 mm or over up to and incl. 30 mm]
245 [Outer diameter 4 mm or over up to and incl. 100 mm /Wall thickness 0.25 mm or over up to and incl. 25 mm]
245 [Outer diameter 5 mm or over up to and incl. 250 mm /Wall thickness 0.5 mm or over up to and incl. 30 mm] 245 [Outer diameter 4 mm or over up to and incl. 250 mm /Wall thickness 0.3 mm or over up to and incl. 30 mm] 245 [Outer diameter 4 mm or over up to and incl. 250 mm /Wall thickness 0.3 mm or over up to and incl. 30 mm] 270 [Outer diameter 4 mm or over up to and incl. 250 mm /Wall thickness 0.15 mm or over up to and incl. 30 mm]
205 [Outer diameter 5 mm or over up to and incl. 250 mm /Wall thickness 0.5 mm or over up to and incl. 25 mm] 245 [Outer diameter 4 mm or over up to and incl. 250 mm /Wall thickness 0.25 mm or over up to and incl. 25 mm] 245 [Outer diameter 4 mm or over up to and incl. 250 mm /Wall thickness 0.25 mm or over up to and incl. 25 mm] 270 [Outer diameter 4 mm or over up to and incl. 250 mm /Wall thickness 0.15 mm or over up to and incl. 25 mm] (continued)
B 8265:2010
Page 83
84
Position Table B.3 (continued) Type: JIS H 3300 Model: 1862 Quality class: 1/2H Specified minimum tensile strength Table B.3 (continued) Type: JIS H 3300 Model: 5010 Quality class: 1/2H Designation (at two positions: one in the fourth column from the left, the other in the rightmost column) Table B.3 (continued) Type: JIS H 3300 Model: 5010 Quality class: 1/2H Specified minimum tensile strength Table B.3 (continued) Type: JIS H 3300 Model: 1565 Quality class: 3/4H Specified minimum tensile strength Table B.3 (continued) Type: JIS H 3300 Model: 1862 Quality class: 3/4H Designation (at two positions: one in the fourth column from the left, the other in the rightmost column) Table B.3 (continued) Type: JIS H 3300 Model: 1862 Quality class: 3/4H Specified minimum tensile strength
ERRATA (6/11)
Error 305 [Outer diameter 4 mm or over up to and incl. 250 mm /Wall thickness 0.15 mm or over up to and incl. 30 mm] C5010T-1/2H C5010T-1/2H
Correct 305 [Outer diameter 4 mm or over up to and incl. 250 mm /Wall thickness 0.15 mm or over up to and incl. 25 mm] C5010T-1/2H C5010TS-1/2H
270 [Outer diameter 4 mm or over up to and incl. 250 mm /Wall thickness 0.15 mm or over up to and incl. 30 mm] 295 [Outer diameter 4 mm or over up to and incl. 250 mm /Wall thickness 0.15 mm or over up to and incl. 30 mm] C1862T-3/4H C1862T-3/4H
270 [Outer diameter 4 mm or over up to and incl. 250 mm /Wall thickness 0.15 mm or over up to and incl. 25 mm] 295[Outer diameter 4 mm or over up to and incl. 250 mm /Wall thickness 0.15 mm or over up to and incl. 25 mm] C1862T-3/4H C1862TS-3/4H
325 [Outer diameter 4 mm or over up to and incl. 250 mm /Wall thickness 0.15 Mm or over up to and incl. 30 mm]
325 [Outer diameter 4 mm or over up to and incl. 250 mm /Wall thickness 0.15 mm or over up to and incl. 25 mm]
(continued)
B 8265:2010
Page 84
Position Table B.3 (continued) Type: JIS H 3300 Model: 5010 Quality class: 3/4H Designation (at two positions: one in the fourth column from the left, the other in the rightmost column) Table B.3 (continued) Type: JIS H 3300 Model: 5010 Quality class: 3/4H Specified minimum tensile strength Table B.3 (continued) Type: JIS H 3300 Model: 1020 Quality class: H Specified minimum tensile strength
Table B.3 (continued) Type: JIS H 3300 Model: 1201, 1220 Quality class: H Specified minimum tensile strength
ERRATA (7/11)
Error C5010T-3/4H C5010T-3/4H
Correct C5010T-3/4H C5010TS-3/4H
295 [Outer diameter 4 mm or over up to and incl. 250 mm /Wall thickness 0.15 mm or over up to and incl. 30 mm] 315 [Outer diameter 25 mm or over up to and incl. 100 mm /Wall thickness 0.3 mm or over up to and incl. 6 mm]
295 [Outer diameter 4 mm or over up to and incl. 250 mm /Wall thickness 0.15 mm or over up to and incl. 25 mm] 315 [Outer diameter 25 mm or under /Wall thickness 0.25 mm or over up to and incl. 3 mm] 315 [Outer diameter over 25 mm up to and incl. 50 mm /Wall thickness 0.9 mm or over up to and incl. 4 mm] 315 [Outer diameter over 50 mm up to and incl. 100 mm /Wall thickness 1.5 mm or over up to and incl. 6 mm] 315 [Outer diameter 25 mm or under /Wall thickness 0.25 mm or over up to and incl. 3 mm] 315 [Outer diameter over 25 mm up to and incl. 50 mm /Wall thickness 0.9 mm or over up to and incl. 4 mm] 315 [Outer diameter over 50 mm up to and incl. 100 mm /Wall thickness 1.5 mm or over up to and incl. 6 mm]
315 [Outer diameter 25 mm or under /Wall thickness 0.3 mm or over up to and incl. 3 mm /Outer diameter over 25 mm up to and incl. 50 mm /Wall thickness 0.9 mm or over up to and incl. 4 mm /Outer diameter over 50 mm up to and incl. 100 mm /Wall thickness 1.5 mm or over up to and incl. 6 mm]
(continued)
B 8265:2010
Page 84
Position Table B.3 (continued) Type: JIS H 3300 Model: 1565 Quality class: H Specified minimum tensile strength
Table B.3 (continued) Type: JIS H 3300 Model: 1862 Quality class: H Designation (at four positions: two in the fourth column from the left, the other two in the rightmost column) Table B.3 (continued) Type: JIS H 3300 Model: 1862 Quality class: H Specified minimum tensile strength
Table B.3 (continued) Type: JIS H 3300 Model: 5010 Quality class: H Designation (at four positions: two in the fourth column from the left, the other two in the rightmost column)
ERRATA (8/11)
Error 400 [Outer diameter 51 mm or under /Wall thickness 0.15 mm or over up to and incl. 4 mm]
C1862T-H C1862T-H
450 [Outer diameter 51 mm or under /Wall thickness 0.15 mm or over up to and incl. 4 mm]
C5010T-H C5010T-H
Correct 400 [Outer diameter 25 mm or under /Wall thickness 0.15 mm or over up to and incl. 3 mm] 400 [Outer diameter over 25 mm up to and incl. 51 mm /Wall thickness 0.15 mm or over up to and incl. 4 mm] C1862T-H C1862TS-H
450 [Outer diameter 25 mm or under /Wall thickness 0.15 mm or over up to and incl. 3 mm] 450 [Outer diameter over 25 mm up to and incl. 51 mm /Wall thickness 0.15 mm or over up to and incl. 4 mm] C5010T-H C5010TS-H
(continued)
B 8265:2010
Page 84
102
Position Table B.3 (continued) Type: JIS H 3300 Model: 5010 Quality class: H Specified minimum tensile strength
199
Table B.4 Type: JIS G 4107 Model dimensions Table C.14 (concluded) Standard composition: 55Ni-21Cr-13.5Mo Grade symbol Table D.1 (continued) Type of materials: Titanium alloy Type 61 Longitudinal elastic coefficient of materials at each temperature, 20 F.9
216
Figure G.2 b) 4)
112
115
Error
Taper over 1/3
ERRATA (9/11)
Error 400 [Outer diameter 51 mm or under /Wall thickness 0.15 mm or over up to and incl. 4 mm]
Type 3 < 63
Correct 400 [Outer diameter 25 mm or under /Wall thickness 0.15 mm or over up to and incl. 3 mm] 400 [Outer diameter over 25 mm up to and incl. 51 mm /Wall thickness 0.15 mm or over up to and incl. 4 mm] Type 3 ≤ 63
N06002
N06022
101
110
The large diameter hole The large diameter hole shall be reinforced as given shall be reinforced as given in a) to c) below. in a) to b) below. Replace the existing figure with the correct one as shown below. Correct
Taper over 1/3
1.5g0 min.
1.5g0 min. Taper 1/3 or under
Taper 1/3 or under Weld centre
Weld centre
（
: Corrected position）
(continued)
B 8265:2010
Page 250
Position Figure I.2 a) 3)
ERRATA (10/11)
Replace the existing figure with the correct one as shown below. Correct
Error
min.
max.
min.
max.
（
Page 253
Position Figure I.4
: Corrected position）
Replace the existing figure with the correct one as shown below. Correct
Error
Metal to metal
Flange II Flange I
Flange I
Flange II
Metal to metal
（
Page 267
Position L.3.2
273
M.1
min.
: Corrected position）
Error The calculated thickness of the bolted flat cover plate shall be as given in a) to c) below. This Annex applies to the calculation of plates of pressure vessels….
Correct The calculated thickness of the bolted flat cover plate shall be as given in a) to d). This Annex applies to the calculated thickness of plates of pressure vessels….
(continued)
B 8265:2010
Page 274
Position Figure M.1 b) Error
ERRATA (11/11)
Replace the existing figure with the correct one as shown below. Correct
（
Page 277
Position M.5 c)
M.6
284
Figure O.2 Below b)
Error The load by which….the total area occupied by the tube hole from the area ed by the tube stay,….. σa: allowable tensile stress of the material…..However, in the case of stays that are fixed by welding, it shall be the allowable tensile stress of the material of the stay…. Meanings of symbols used in the figures: …… The position of the notch to be given….the thermally affected area.
: Corrected position）
Correct The load by which….the total area occupied by the tube hole and the area occupied by the stay tube from the area ed by the tube stay,….. σa: allowable tensile stress of the material…..However, in the case of stays having welds, it shall be the allowable tensile stress of the material of the stay…. Meanings of symbols used in the figures: …… The position of the notch to be given….the thermally affected area. When taking two test pieces in the case of welding metal over 38 mm in thickness, in addition to the one shown in the figure, another shall be taken at the opposite side of the base metal such that the test piece axis is at 0.25 t from the base metal surface.
(concluded)
Page
Position
32
Figure 11 e) (below the figure)
36
6.2, Table 2
Error
Correct
tw is the pipe thickness of schedule 160.
tw is the pipe thickness of schedule 160. Nominal diameter of the pipe fitting is 80A (DN80) or under.
Type of
Efficiency of welded ts ( )
Type of
ts
Percentage of applying the
ts
b) 20 ％
Percentage
of
applying
the
radiographic examination
radiographic examination a) 100 ％
Efficiency of welded ts ( )
a) 100 ％
c) Not
b) 20 ％
c) Not applied
applied B－1
1.00
0.95
0.70
B－1
1.00
0.95
0.70
B－2
0.90
0.85
0.65
B－2
0.90
0.85
0.65
－
－
0.60
B－3
－
－
0.60
B－3
L－1
－
－
0.55
L－1
－
－
0.55
0.50
L－2
－
－
0.50
0.45
L－3
－
－
0.45
L－2 L－3
－ －
－ －
NOTE: The efficiency of welded ts in the case of cylindrical shells apply to longitudinal and circumference ts. However, the calculated thickness of cylindrical shells applies to the longitudinal ts.
(continued)
B 8265:2010
Page 40 6.5 c)
Position 6.5 c)
ERRATA (2/11)
Error See below.
Correct See below.
Error: For the hub part of tube plates with hubs or flat end plates with hubs (only in the case of machining from plates), the ultrasonic examination of the whole volume of the hub part from the two directions, the radial and axial, of the hub shall be performed in accordance with JIS G 0801, and the judging criteria given in 1) and 2) below shall be satisfied. Correct: For the hub part of tube plates with hubs or flat end plates with hubs (only in the case of machining from plates), the ultrasonic examination of the whole volume of the hub part from the two directions, the radial and axial, of the hub shall be performed in accordance with JIS G 0801 before and after machining, and the judging criteria given in 1) and 2) below shall be satisfied.
Page 60
63
Position Table B.1 (continued) Type: JIS G 3127 Designation: SL5N590 Base metal class Table B.1 (continued) Type: JIS G 3452 Designation: SGP Fabrication method Table B.1 (continued) Type: JIS G 3454 Designation: STPG370 Fabrication method Table B.1 (continued) Type: JIS G 3454 Designation: STPG410 Fabrication method Table B.1 (continued) Type: JIS G 3456 Designation: STPT370 Fabrication method Table B.1 (continued) Type: JIS G 3456 Designation: STPT410 Fabrication method Table B.1 (continued) Type: JIS G 3457 Designation: STPY400 Fabrication method
Error 9B
Correct 11A
E B
W B
S E
S W
S E
S W
S E
S W
S E
S W
A
W
(continued)
B 8265:2010
Page 65
66
67
Position Table B.1 (continued) Type: JIS G 3460 Designation: STPL380 Fabrication method Table B.1 (continued) Type: JIS G 3461 Designation: STB340 Fabrication method Table B.1 (continued) Type: JIS G 3461 Designation: STB410 Fabrication method Table B.1 (continued) Type: JIS G 3461 Designation: STB510 Fabrication method Table B.1 (continued) Type: JIS G 3462 Designation: STBA12 Fabrication method Table B.1 (continued) Type: JIS G 3462 Designation: STBA13 Fabrication method Table B.1 (continued) Type: JIS G 3462 Designation: STBA20 Fabrication method Table B.1 (continued) Type: JIS G 3462 Designation: STBA22 Fabrication method Table B.1 (continued) Type: JIS G 3463 Designation: SUS329J4LTB Fabrication method Type: JIS G 3463 Designation: SUS329J4LTB Add the values in the right as the allowable tensile stress values for fabrication method W (added above), for temperatures 40 °C, 75 °C, 100 °C, 125 °C, 150 °C, 175 °C, 200 °C, 225 °C, 250 °C, 275 °C and 300 °C, respectively.
ERRATA (3/11)
Error S E
Correct S W
S, E E
S, W W
S, E E
S, W W
S, E E
S, W W
S, E E
S, W W
S, E E
S, W W
S, E E
S, W W
S, E E
S, W W
–
–
S W
132, 132, 131, 129, 128, 125, 123, 122, 120, 119, 119
(continued)
B 8265:2010
Page 68
77
Position Table B.1 (continued) Type: JIS G 3464 Designation: STBL380 Fabrication method Table B.1 (continued) NOTE 3
80
Table B.1 (continued) Note ah)
83
Table B.3 (continued) Type: JIS H 3300 Model: 1020 Quality class: O Specified minimum tensile strength Table B.3 (continued) Type: JIS H 3300 Model: 1201 Quality class: O Specified minimum tensile strength Table B.3 (continued) Type: JIS H 3300 Model: 1220 Quality class: O Specified minimum tensile strength Table B.3 (continued) Type: JIS H 3300 Model: 1020 Quality class: OL Specified minimum tensile strength
ERRATA (4/11)
Error S, E E
S : seamless pipes; E : electric resistance welded tubes; A : submerged arc welding tubes; W : automatic arc welding tubes or electric resistance welded tubes. The external pressure chart number in this row may be applied to JIS G 4051, JIS G 4303, and JIS G 4311, only when used for stiffening rings 205 [Outer diameter 4 mm or over up to and incl. 100 mm /Wall thickness 0.3 mm or over up to and incl. 30 mm] 205 [Outer diameter 4 mm or over up to and incl. 250 mm /Wall thickness 0.3 mm or over up to and incl. 30 mm] 205 [Outer diameter 4 mm or over up to and incl. 250 mm /Wall thickness 0.3 mm or over up to and incl. 30 mm] 205 [Outer diameter 4 mm or over up to and incl. 100 mm /Wall thickness 0.3 mm or over up to and incl. 30 mm]
Correct S,W W
S: seamless pipes ; B: forge-welded tubes ; W : electric resistance welded tubes; submerged arc welding tubes; automatic arc welding tubes or laser welding tubes. The external pressure chart number in this row may be applied only when used for stiffening rings
205 [Outer diameter 4 mm or over up to and incl. 100 mm /Wall thickness 0.25 mm or over up to and incl. 30 mm] 205 [Outer diameter 4 mm or over up to and incl. 250 mm /Wall thickness 0.25 mm or over up to and incl. 30 mm] 205 [Outer diameter 4 mm or over up to and incl. 250 mm /Wall thickness 0.25 mm or over up to and incl. 30 mm] 205 [Outer diameter 4 mm or over up to and incl. 100 mm /Wall thickness 0.25 mm or over up to and incl. 30 mm]
(continued)
B 8265:2010
Page 83
ERRATA (5/11)
Position Table B.3 (continued) Type: JIS H 3300 Model: 1201 Quality class: OL Specified minimum tensile strength Table B.3 (continued) Type: JIS H 3300 Model: 1220 Quality class: OL Specified minimum tensile strength
Error 205 [Outer diameter 4 mm or over up to and incl. 250 mm /Wall thickness 0.3 mm or over up to and incl. 30 mm] 205 [Outer diameter 4 mm or over up to and incl. 250 mm /Wall thickness 0.3 mm or over up to and incl. 30 mm]
Correct 205 [Outer diameter 4 mm or over up to and incl. 250 mm /Wall thickness 0.25 mm or over up to and incl. 30 mm] 205 [Outer diameter 4 mm or over up to and incl. 250 mm /Wall thickness 0.25 mm or over up to and incl. 30 mm]
Table B.3 (continued) Type: JIS H 3300 Model: 1020 Quality class: 1/2H Specified minimum tensile strength Table B.3 (continued) Type: JIS H 3300 Model: 1100 Quality class: 1/2H Specified minimum tensile strength Table B.3 (continued) Type: JIS H 3300 Model: 1201 Quality class: 1/2H Specified minimum tensile strength Table B.3 (continued) Type: JIS H 3300 Model: 1220 Quality class: 1/2H Specified minimum tensile strength Table B.3 (continued) Type: JIS H 3300 Model: 1565 Quality class: 1/2H Specified minimum tensile strength
245 [Outer diameter 4 mm or over up to and incl. 100 mm /Wall thickness 0.3 mm or over up to and incl. 30 mm]
245 [Outer diameter 4 mm or over up to and incl. 100 mm /Wall thickness 0.25 mm or over up to and incl. 25 mm]
245 [Outer diameter 5 mm or over up to and incl. 250 mm /Wall thickness 0.5 mm or over up to and incl. 30 mm] 245 [Outer diameter 4 mm or over up to and incl. 250 mm /Wall thickness 0.3 mm or over up to and incl. 30 mm] 245 [Outer diameter 4 mm or over up to and incl. 250 mm /Wall thickness 0.3 mm or over up to and incl. 30 mm] 270 [Outer diameter 4 mm or over up to and incl. 250 mm /Wall thickness 0.15 mm or over up to and incl. 30 mm]
205 [Outer diameter 5 mm or over up to and incl. 250 mm /Wall thickness 0.5 mm or over up to and incl. 25 mm] 245 [Outer diameter 4 mm or over up to and incl. 250 mm /Wall thickness 0.25 mm or over up to and incl. 25 mm] 245 [Outer diameter 4 mm or over up to and incl. 250 mm /Wall thickness 0.25 mm or over up to and incl. 25 mm] 270 [Outer diameter 4 mm or over up to and incl. 250 mm /Wall thickness 0.15 mm or over up to and incl. 25 mm] (continued)
B 8265:2010
Page 83
84
Position Table B.3 (continued) Type: JIS H 3300 Model: 1862 Quality class: 1/2H Specified minimum tensile strength Table B.3 (continued) Type: JIS H 3300 Model: 5010 Quality class: 1/2H Designation (at two positions: one in the fourth column from the left, the other in the rightmost column) Table B.3 (continued) Type: JIS H 3300 Model: 5010 Quality class: 1/2H Specified minimum tensile strength Table B.3 (continued) Type: JIS H 3300 Model: 1565 Quality class: 3/4H Specified minimum tensile strength Table B.3 (continued) Type: JIS H 3300 Model: 1862 Quality class: 3/4H Designation (at two positions: one in the fourth column from the left, the other in the rightmost column) Table B.3 (continued) Type: JIS H 3300 Model: 1862 Quality class: 3/4H Specified minimum tensile strength
ERRATA (6/11)
Error 305 [Outer diameter 4 mm or over up to and incl. 250 mm /Wall thickness 0.15 mm or over up to and incl. 30 mm] C5010T-1/2H C5010T-1/2H
Correct 305 [Outer diameter 4 mm or over up to and incl. 250 mm /Wall thickness 0.15 mm or over up to and incl. 25 mm] C5010T-1/2H C5010TS-1/2H
270 [Outer diameter 4 mm or over up to and incl. 250 mm /Wall thickness 0.15 mm or over up to and incl. 30 mm] 295 [Outer diameter 4 mm or over up to and incl. 250 mm /Wall thickness 0.15 mm or over up to and incl. 30 mm] C1862T-3/4H C1862T-3/4H
270 [Outer diameter 4 mm or over up to and incl. 250 mm /Wall thickness 0.15 mm or over up to and incl. 25 mm] 295[Outer diameter 4 mm or over up to and incl. 250 mm /Wall thickness 0.15 mm or over up to and incl. 25 mm] C1862T-3/4H C1862TS-3/4H
325 [Outer diameter 4 mm or over up to and incl. 250 mm /Wall thickness 0.15 Mm or over up to and incl. 30 mm]
325 [Outer diameter 4 mm or over up to and incl. 250 mm /Wall thickness 0.15 mm or over up to and incl. 25 mm]
(continued)
B 8265:2010
Page 84
Position Table B.3 (continued) Type: JIS H 3300 Model: 5010 Quality class: 3/4H Designation (at two positions: one in the fourth column from the left, the other in the rightmost column) Table B.3 (continued) Type: JIS H 3300 Model: 5010 Quality class: 3/4H Specified minimum tensile strength Table B.3 (continued) Type: JIS H 3300 Model: 1020 Quality class: H Specified minimum tensile strength
Table B.3 (continued) Type: JIS H 3300 Model: 1201, 1220 Quality class: H Specified minimum tensile strength
ERRATA (7/11)
Error C5010T-3/4H C5010T-3/4H
Correct C5010T-3/4H C5010TS-3/4H
295 [Outer diameter 4 mm or over up to and incl. 250 mm /Wall thickness 0.15 mm or over up to and incl. 30 mm] 315 [Outer diameter 25 mm or over up to and incl. 100 mm /Wall thickness 0.3 mm or over up to and incl. 6 mm]
295 [Outer diameter 4 mm or over up to and incl. 250 mm /Wall thickness 0.15 mm or over up to and incl. 25 mm] 315 [Outer diameter 25 mm or under /Wall thickness 0.25 mm or over up to and incl. 3 mm] 315 [Outer diameter over 25 mm up to and incl. 50 mm /Wall thickness 0.9 mm or over up to and incl. 4 mm] 315 [Outer diameter over 50 mm up to and incl. 100 mm /Wall thickness 1.5 mm or over up to and incl. 6 mm] 315 [Outer diameter 25 mm or under /Wall thickness 0.25 mm or over up to and incl. 3 mm] 315 [Outer diameter over 25 mm up to and incl. 50 mm /Wall thickness 0.9 mm or over up to and incl. 4 mm] 315 [Outer diameter over 50 mm up to and incl. 100 mm /Wall thickness 1.5 mm or over up to and incl. 6 mm]
315 [Outer diameter 25 mm or under /Wall thickness 0.3 mm or over up to and incl. 3 mm /Outer diameter over 25 mm up to and incl. 50 mm /Wall thickness 0.9 mm or over up to and incl. 4 mm /Outer diameter over 50 mm up to and incl. 100 mm /Wall thickness 1.5 mm or over up to and incl. 6 mm]
(continued)
B 8265:2010
Page 84
Position Table B.3 (continued) Type: JIS H 3300 Model: 1565 Quality class: H Specified minimum tensile strength
Table B.3 (continued) Type: JIS H 3300 Model: 1862 Quality class: H Designation (at four positions: two in the fourth column from the left, the other two in the rightmost column) Table B.3 (continued) Type: JIS H 3300 Model: 1862 Quality class: H Specified minimum tensile strength
Table B.3 (continued) Type: JIS H 3300 Model: 5010 Quality class: H Designation (at four positions: two in the fourth column from the left, the other two in the rightmost column)
ERRATA (8/11)
Error 400 [Outer diameter 51 mm or under /Wall thickness 0.15 mm or over up to and incl. 4 mm]
C1862T-H C1862T-H
450 [Outer diameter 51 mm or under /Wall thickness 0.15 mm or over up to and incl. 4 mm]
C5010T-H C5010T-H
Correct 400 [Outer diameter 25 mm or under /Wall thickness 0.15 mm or over up to and incl. 3 mm] 400 [Outer diameter over 25 mm up to and incl. 51 mm /Wall thickness 0.15 mm or over up to and incl. 4 mm] C1862T-H C1862TS-H
450 [Outer diameter 25 mm or under /Wall thickness 0.15 mm or over up to and incl. 3 mm] 450 [Outer diameter over 25 mm up to and incl. 51 mm /Wall thickness 0.15 mm or over up to and incl. 4 mm] C5010T-H C5010TS-H
(continued)
B 8265:2010
Page 84
102
Position Table B.3 (continued) Type: JIS H 3300 Model: 5010 Quality class: H Specified minimum tensile strength
199
Table B.4 Type: JIS G 4107 Model dimensions Table C.14 (concluded) Standard composition: 55Ni-21Cr-13.5Mo Grade symbol Table D.1 (continued) Type of materials: Titanium alloy Type 61 Longitudinal elastic coefficient of materials at each temperature, 20 F.9
216
Figure G.2 b) 4)
112
115
Error
Taper over 1/3
ERRATA (9/11)
Error 400 [Outer diameter 51 mm or under /Wall thickness 0.15 mm or over up to and incl. 4 mm]
Type 3 < 63
Correct 400 [Outer diameter 25 mm or under /Wall thickness 0.15 mm or over up to and incl. 3 mm] 400 [Outer diameter over 25 mm up to and incl. 51 mm /Wall thickness 0.15 mm or over up to and incl. 4 mm] Type 3 ≤ 63
N06002
N06022
101
110
The large diameter hole The large diameter hole shall be reinforced as given shall be reinforced as given in a) to c) below. in a) to b) below. Replace the existing figure with the correct one as shown below. Correct
Taper over 1/3
1.5g0 min.
1.5g0 min. Taper 1/3 or under
Taper 1/3 or under Weld centre
Weld centre
（
: Corrected position）
(continued)
B 8265:2010
Page 250
Position Figure I.2 a) 3)
ERRATA (10/11)
Replace the existing figure with the correct one as shown below. Correct
Error
min.
max.
min.
max.
（
Page 253
Position Figure I.4
: Corrected position）
Replace the existing figure with the correct one as shown below. Correct
Error
Metal to metal
Flange II Flange I
Flange I
Flange II
Metal to metal
（
Page 267
Position L.3.2
273
M.1
min.
: Corrected position）
Error The calculated thickness of the bolted flat cover plate shall be as given in a) to c) below. This Annex applies to the calculation of plates of pressure vessels….
Correct The calculated thickness of the bolted flat cover plate shall be as given in a) to d). This Annex applies to the calculated thickness of plates of pressure vessels….
(continued)
B 8265:2010
Page 274
Position Figure M.1 b) Error
ERRATA (11/11)
Replace the existing figure with the correct one as shown below. Correct
（
Page 277
Position M.5 c)
M.6
284
Figure O.2 Below b)
Error The load by which….the total area occupied by the tube hole from the area ed by the tube stay,….. σa: allowable tensile stress of the material…..However, in the case of stays that are fixed by welding, it shall be the allowable tensile stress of the material of the stay…. Meanings of symbols used in the figures: …… The position of the notch to be given….the thermally affected area.
: Corrected position）
Correct The load by which….the total area occupied by the tube hole and the area occupied by the stay tube from the area ed by the tube stay,….. σa: allowable tensile stress of the material…..However, in the case of stays having welds, it shall be the allowable tensile stress of the material of the stay…. Meanings of symbols used in the figures: …… The position of the notch to be given….the thermally affected area. When taking two test pieces in the case of welding metal over 38 mm in thickness, in addition to the one shown in the figure, another shall be taken at the opposite side of the base metal such that the test piece axis is at 0.25 t from the base metal surface.
(concluded)
More Documents from "dh" 3l2p1d
Ian Goodfellow, Yoshua Bengio, Aaron Courville-deep Learning [pre-pub Version]-mit Press (2016).pdf 2lm5q
November 2019 127
Jis_b_08265_000_000_2010_cor_2_201312_e_ch 2z3v3u
October 2020 0
K3 Apd Di Puskesmas.docx 203f6m
April 2020 23
6l6m1j
October 2020 0
Extreme Adjectives y6q24
August 2021 0