Parallel Batteries _ Dc Circuits - Electronics Textbook 1r6i5h

6/13/2015

Parallel Batteries : DC Circuits ­ Electronics Textbook

 (https://www.facebook.com/allaboutcircuits)  (https://twitter.com/AllAboutCircuit)  (https://www.linkedin.com/company/all-about-circuits)

Table of Contents   

Parallel Batteries Chapter 3 - DC Circuits

PARTS AND MATERIALS

Four 6-volt batteries 12-volt light bulb, 25 or 50 watt Lamp socket High-wattage 12-volt lamps may be purchased from recreational vehicle (RV) and boating supply stores. Common sizes are 25 watt and 50 watt. This lamp will be used as a “heavy” load for your batteries (heavy load = one that draws substantial current). A regular household (120 volt) lamp socket will work just fine for these low-voltage “RV” lamps.

CROSS-REFERENCES Lessons In Electric Circuits, Volume 1, chapter 5: “Series and Parallel Circuits” Lessons In Electric Circuits, Volume 1, chapter 11: “Batteries and Power Systems”

LEARNING OBJECTIVES

Voltage source regulation Boosting current capacity through parallel connections

SCHEMATIC DIAGRAM

ILLUSTRATION

http://www.allaboutcircuits.com/textbook/experiments/chpt­3/parallel­batteries/

1/5

6/13/2015

Parallel Batteries : DC Circuits ­ Electronics Textbook

INSTRUCTIONS Begin this experiment by connecting one 6-volt battery to the lamp. The lamp, designed to operate on 12 volts, should glow dimly when powered by the 6-volt battery. Use your voltmeter to read voltage across the lamp like this:

The voltmeter should a voltage lower than the usual voltage of the battery. If you use your voltmeter to read the voltage directly at the battery terminals, you will measure a low voltage there as well. Why is this? The large current drawn by the high-power lamp causes the voltage at the battery terminals to “sag” or “droop,” due to voltage dropped across resistance internal to the battery.

We may overcome this problem by connecting batteries in parallel with each other, so that each battery only has to supply a fraction of the total current demanded by the lamp. Parallel connections involve making all the positive (+) battery terminals electrically common to each other by connection through jumper wires, and all negative (-) terminals common to each other as well. Add one battery at a time in parallel, noting the lamp voltage with the addition of each new, parallel-connected battery:

http://www.allaboutcircuits.com/textbook/experiments/chpt­3/parallel­batteries/

2/5

6/13/2015

Parallel Batteries : DC Circuits ­ Electronics Textbook

There should also be a noticeable difference in light intensity as the voltage “sag” is improved. Try measuring the current of one battery and comparing it to the total current (light bulb current). Shown here is the easiest way to measure single-battery current:

By breaking the circuit for just one battery, and inserting our ammeter within that break, we intercept the current of that one battery and are therefore able to measure it. Measuring total current involves a similar procedure: make a break somewhere in the path that total current must take, then insert the ammeter within than break:

http://www.allaboutcircuits.com/textbook/experiments/chpt­3/parallel­batteries/

3/5

6/13/2015

Parallel Batteries : DC Circuits ­ Electronics Textbook

Note the difference in current between the single-battery and total measurements. To obtain maximum brightness from the light bulb, a series-parallel connection is required. Two 6-volt batteries connected series-aiding will provide 12 volts. Connecting two of these series-connected battery pairs in parallel improves their current-sourcing ability for minimum voltage sag:

← Previous Page (/textbook/experiments/chpt-3/series-batteries/) Next Page → (/textbook/experiments/chpt-3/voltage-divider/)



(https://www.facebook.com/sharer/sharer.php?

u=http://www.allaboutcircuits.com/textbook/experiments/chpt-3/parallel-batteries)



(https://twitter.com/share?url=http://www.allaboutcircuits.com/textbook/experiments/chpt-

3/parallel-batteries&via=allaboutcircuit)



(https://plus.google.com/share?

url=http://www.allaboutcircuits.com/textbook/experiments/chpt-3/parallel-batteries)

 (https://www.linkedin.com/shareArticle? WHO WE ARE mini=true&url=http://www.allaboutcircuits.com/textbook/experiments/chpt-3/parallel-batteries) Published under the and conditions of the Design Science License (https://www.gnu.org/licenses/dsl.html) http://www.allaboutcircuits.com/textbook/experiments/chpt­3/parallel­batteries/

4/5

6/13/2015

Parallel Batteries : DC Circuits ­ Electronics Textbook

Published under the and conditions of the Design Science License (https://www.gnu.org/licenses/dsl.html)

(/)

 

More  (/-us/)

CONTENT

CATEGORIES

News (/news/)

Trending (/)

Projects (/projects/)

Arduino (/latest/arduino/)

Technical Articles (/technical-articles/)

Power (/latest/power/)

Textbook (/textbook/)

Embedded (/latest/embedded/)

s (/s/)

IoT (/latest/iot/)

Video Lectures (/video-lectures/)

Sensors (/latest/sensors/)

Worksheets (/worksheets/)

Digital ICs (/latest/digital-ics/)

Forum (//forum.allaboutcircuits.com/)

Test & Measure (/latest/test-and-measure/)

CONNECT WITH US Facebook

YouTube

(https://www.facebook.com/allaboutcircuits)

(https://www.youtube.com/channel/UCYTq2bhe5pim45p

Twitter (https://twitter.com/AllAboutCircuit)

gDjw)

Us (/-us/)

LinkedIn (https://www.linkedin.com/company/all-aboutcircuits)

 

SIGN UP Enter your email address



© EETech Media, LLC (http://eetech.com/). All rights reserved

http://www.allaboutcircuits.com/textbook/experiments/chpt­3/parallel­batteries/

5/5