Pds Hempel's Galvosil 15700 En-gb 1w2p1w

Product Data HEMPEL'S GALVOSIL 15700 15700: LIQUID 15709: HEMPEL’S ZINC METAL PIGMENT 97170/97140 Description:

HEMPEL’S GALVOSIL 15700 is a two-component, solvent-borne, self-curing, inorganic zinc silicate with outstanding resistance against weathering and abrasion. It has excellent chemical resistance within the pH range 6-9. Offers cathodic protection of local mechanical damage. Hempel's Zinc metal pigment 97170 is in full compliance with ISO 3549 and ASTM D520 type I. This is available in 15700 19840. Hempel's Zinc metal pigment 97140 is additionally in compliance with ASTM D520 type II. This is available in 15700 1984Z.

Recommended use:

As a general purpose, heavy-duty, rust-preventing primer. As a single, complete coating for long-term protection of steel exposed to moderately to severely corrosive environment and to abrasion. As a tank lining in accordance with the CARGO PROTECTION GUIDE. In compliance with SSPC-Paint 20, type 1, level 1 and ISO 12944-5.

Service temperature:

Resistant to permanent (non-cyclic) dry temperatures as well as occasionally dry peak temperatures up to maximum: 500°C/932°F. Resistant to cyclic dry temperatures up to 400°C/752°F. Further information - see REMARKS overleaf.

Certificates/Approvals:

Meets the requirements laid down in ASTM A-490 Class "B" for Slip-Co-efficient and Creep Resistance. Tested according to section 175.300 of the Code of Federal Regulations Title 21 – Liquid Foodstuff. Consult Hempel for details.

Availability:

Part of Group Assortment. Local availability subject to confirmation.

PHYSICAL CONSTANTS: Shade nos/Colours: Finish: Volume solids, %: Theoretical spreading rate: Flash point: Specific gravity: Surface-dry: Through-dry: Fully cured: VOC content: Shelf life:

-

19840 / Metal grey Flat 64 ± 1 12.8 m2/l [513.3 sq.ft./US gallon] - 50 micron/2 mils 14 °C [57.2 °F] 2.7 kg/litre [22.2 lbs/US gallon] 0.5 hour(s) 20°C/68°F (60-75% RH) 45 minute(s) 20°C/68°F 16 hour(s) 20°C/68°F and minimum 65% RH (see REMARKS overleaf) 434 g/l [3.6 lbs/US gallon] 6 months , 25°C/77°F for the LIQUID and 3 years for HEMPEL'S ZINC METAL PIGMENT (stored in closed container) from time of production. Shelf life is dependent on storage temperature. Shelf life is reduced at storage temperatures above: 25°C/77°F. Do not store above the following temperature: 40°C/105°F. Shelf life is exceeded if the liquid is gelled or if the mixed product forms gels before application. The physical constants stated are nominal data according to the HEMPEL Group's approved formulas.

APPLICATION DETAILS: Version, mixed product: Mixing ratio: Application method: Thinner (max.vol.): Pot life: Nozzle orifice: Nozzle pressure: Cleaning of tools: Indicated film thickness, dry: Indicated film thickness, wet: Overcoat interval, min: Overcoat interval, max: Safety:

15700 LIQUID 15709: HEMPEL’S ZINC METAL PIGMENT 97170/97140 3.1 : 6.9 by weight Airless spray / Air spray / Brush (touch up) [08700 and/or 0870M (30%) See separate APPLICATION INSTRUCTIONS ]/ 08700 (50%) / 08700 (10%) 4 hour(s) 20°C/68°F 0.019 - 0.023 " 100 bar [1450 psi] (Airless spray data are indicative and subject to adjustment) HEMPEL'S THINNER 08700 50 micron [2 mils] See separate APPLICATION INSTRUCTIONS 75 micron [3 mils] According to separate APPLICATION INSTRUCTIONS According to separate APPLICATION INSTRUCTIONS Handle with care. Before and during use, observe all safety labels on packaging and paint containers, consult HEMPEL Safety Data Sheets and follow all local or national safety regulations.

-

Date of issue: March 2016

Page: 1/2

Product Data HEMPEL'S GALVOSIL 15700 SURFACE PREPARATION:

Remove oil and grease etc. thoroughly with suitable detergent. Remove salts and other contaminants by high pressure fresh water cleaning. Abrasive blasting with sharp abrasive to minimum Sa 2½ (ISO 8501-1:2007) with a surface profile equivalent to Rugotest No. 3, BN10, Keane-Tator Comparator, min. 3.0 G/S, or ISO Comparator rough Medium (G). In case of new steel to be exposed to no more than medium aggressive (industrial) environment and without any extraordinary demands to lifetime, a surface preparation degree of SSPC-SP6 may suffice. See separate APPLICATION INSTRUCTIONS and corresponding PAINTING SPECIFICATION for cargo tanks.

APPLICATION CONDITIONS:

The surface must be completely clean and dry at the time of application and its temperature must be above the dew point to avoid condensation. At temperatures ranging from 0°C/32°F to 40°C/105°F, curing needs minimum 50% relative humidity. Curing is retarded at lower temperature and lower humidity. In confined spaces provide adequate ventilation during application and drying. See separate APPLICATION INSTRUCTIONS

SUBSEQUENT COAT:

As a tank coating: None, i.e. no other paints are acceptable in combination with the product. Otherwise according to specification.

REMARKS: Weathering/service temperatures: Wet service temperature, non-saline water: max 60°C/140°F Wet service temperature, other liquids: Consult the corresponding CARGO PROTECTION GUIDE Hot sea water washing and (low pressure) steam cleaning should never be executed on tank coatings which have not been in service for at least one month. HEMPEL about temperature permissible. Film thicknesses/thinning: Thinning: For application at high temperatures, a special thinner is available. Use: HEMPEL'S THINNER 08740

Note:

HEMPEL'S THINNER 0870M can be used to accelerate curing. (See separate APPLICATION INSTRUCTIONS) HEMPEL'S THINNER 0870M is not allowed to be used inside tanks. HEMPEL'S GALVOSIL 15700 For professional use only.

ISSUED BY: HEMPEL A/S 1570019840 X Move PDS Disclaimer to Second pagedent on both temperature and humidity. Deviations from the standard conditions may shorten or prolong the overcoating intervals. Full curing will be obtained after: 0°C/32°F and 65% RH: 3 days 10°C/50°F and minimum 65% RH: 36 hours 20°C/68°F and minimum 65% RH: 16 hours (A certain degree of curing does take place at temperatures below 0°C/32°F, but at an extremely low speed) (Consult the separate APPLICATION INSTRUCTIONS) The state of curing should be checked before overcoating, a resistance rating of minimum 4 by ASTM D4752 is required. MEK (Methyl Ethyl Ketone) may be substituted by Hempel Thinner 08700 for the test. This Product Data Sheet supersedes those previously issued. For explanations, definitions and scope, see “Explanatory Notes” available on www.hempel.com. Data, specifications, directions and recommendations given in this data sheet represent only test results or experience obtained under controlled or specially defined circumstances. Their accuracy, completeness or appropriateness under the actual conditions of any intended use of the Products herein must be determined exclusively by the Buyer and/or . The Products are supplied and all technical assistance is given subject to HEMPEL's GENERAL CONDITIONS OF SALES, DELIVERY AND SERVICE, unless otherwise expressly agreed in writing. The Manufacturer and Seller disclaim, and Buyer and/or waive all claims involving, any liability, including but not limited to negligence, except as expressed in said GENERAL CONDITIONS for all results, injury or direct or consequential losses or damages arising from the use of the Products as recommended above, on the overleaf or otherwise. Product data are subject to change without notice and become void five years from the date of issue.

Date of issue: March 2016

Page: 2/2