Hybrid Racing Z3 K-swap Shifter Install Guide 503s1b

Install Guide for Z3 K-Swap Shifter This product may not be legal for highway use. Hybrid Racing is not responsible for any direct or indirect, actual or incidental expense attributed to the use of any performance parts sold by Hybrid Racing LLC. Purchasers agree to all of the of this agreement upon the purchase of parts.

    

Features: Friction reducing and wear-compensating center pivot point. Anodized aluminum front and side rockers Independently adjustable front/back and left/right throw which can be set between 85% and 45% of the OEM 8th Gen Civic shifter. Adjustable shift knob height and position. Rubber seal to keep out road noise, debris, and exhaust heat

 

     

Recommend Tools: Drill with 3/8” drill bit 3mm, 4mm, 5mm, 6mm allen wrench Package Contents: (1) Short shifter assembly with aluminum dust shield (4) M8 allen bolts with washers (1) Hybrid Racing shifter cable bracket (1) OEM shifter cable bracket (1) Rubber gasket (3) M6 allen bolts with washers

Important!! Please read the entire install guide twice before starting your installation. No, really it’s a good idea to read it twice before you begin so everything goes smooth ;)

1

Install Guide STEP 1: Using a 3mm allen wrench remove the (4) M4 bolts securing the aluminum dust cover to the shifter assembly.

STEP 2: Insert the shifter assembly from the bottom and with a 6mm allen wrench, secure it to the center tunnel on the rear side with (2) of the supplied M8 bolts as shown in FIG 2.

STEP 3: Once the shifter assembly is held snug in the center tunnel, push it up flat against the car and mark the center of the holes for the (2) front mounting bolts as illustrated in FIG 3. 2

Install Guide STEP 4: Remove the shifter assembly, then using a drill with 3/8” drill bit, drill a hole at the two marks you made. (May be a good idea to drill with an 1/8” drill bit for a pilot hole first)

STEP 5: Place the rubber gasket atop the shifter assembly and secure it to the baseplate with the (4) plastic push-in rivets. If your shifter appears as the one in FIG 5 you are ready to .

STEP 6: Install the shifter assembly with the rubber gasket installed back into the center tunnel as you did in step 2 as shown in FIG 6. Loosely thread the (2) M8 bolts in, do not tighten yet. 3

Install Guide STEP 7: With the same 6mm allen wrench, go inside of the car to install the (2) M8 bolts that hold the front of the shifter assembly up. Since the shifter is loosely mounted from the bottom, grab the shifter arm to pull up on the assembly and line the holes up as shown in FIG 7. Once you have them both threaded in, tighten them down.

STEP 8: Go back under the car and using a 6mm allen wrench again, tighten the (2) rear mounting bolts. If yours appears as the one in FIG 8 it ready to have the cables installed.

Cable Selection The next section of this install guide includes the installation of the cables. Before you can install cables you need to decide which cables you are going to use, OEM or Hybrid Racing. Once you have chosen which cables you would like to use you can move on to step 9.

4

OEM Cable Install STEP 9A: Locate the OEM cable keeper in the bag of hardware that came with the shifter. You need the one shown in FIG 9A.

STEP 9B: Starting with the lower cable shown in FIG 9B, snap the endlinks onto the rocker arms and then slide shifter cable bases into grooves of the base. (NOTE: These steps should be done with the shifter attached to the car, these pictures are shown off of the car for better reference)

STEP 9C: Slide the OEM cable keeper over the cable bases and using a 4mm allen wrench thread in and tighten the (2) M6 bolts as illustrated in FIG 9C.

5

Hybrid Racing Cable Install STEP 9A: Locate the Hybrid Racing cable keeper in the bag of hardware that came with the shifter. You need the one shown in FIG 9A.

STEP 9B: Starting with the lower cable shown in FIG 9B, snap the endlinks onto the rocker arms and then pull back on the cables and place the cable bases in the corresponding holes. (NOTE: These steps should be done with the shifter attached to the car, these pictures are shown off of the car for better reference)

STEP 9C: Slide the Hybrid Racing cable keeper into the grooves of the cable bases and using a 4mm allen wrench thread in and tighten the (3) M6 bolts as illustrated in FIG 9C. 6

Install Guide STEP 10: Using a 3mm allen wrench and the (4) M4 bolts you removed in step 1, secure the dust shield to the shifter assembly. Once you have done this and you shifter appears as the one in FIG 10, you are ready to move into the interior of the car.

STEP 11: Slide the offset onto the lower shifting arm, rotate it to your desired position, tighten the lower offset bolt with a 5mm wrench as shown in FIG 11A. Also, place the upper shifter rod to the desired position and tighten the upper offset bolt with a 5mm allen wrench.

STEP 12: Thread your shift knob onto the upper shift rod, and lock into position by tightening the binding nut with a 17mm wrench as shown in FIG 12A. Once you are done with the shift knob your installed shifter should appear as the one in FIG 12B.

7

If you have any questions or comments, please email at [email protected] Legal Disclaimer s assume all cost and risk associated with these or any other items purchased from Hybrid Racing LLC. Parts sold or manufactured by Hybrid Racing LLC may not meet legal requirements for use on public roads. People thinking about purchasing product(s) from Hybrid Racing LLC should check with their local and state authorities for legality. It is the ’s responsibility to know and comply with all local and federal laws and regulations. Use or installation of Hybrid Racing LLC products may affect insurance and/or vehicle warranty coverage. It is the ’s sole responsibility for consequences that may occur due to having the product installed in his/her vehicle. Hybrid Racing LLC assumes no legal responsibilities and/or liabilities, whether to ’s vehicle, engine, person(s), and/or property(s), that result from the use of, or servicing of a vehicle of which a Hybrid Racing LLC product has been installed/attempted to be installed, or to any other vehicle(s) and/or person(s), regardless of whether or not this product has any involvement directly or indirectly and/or liability, and/or whether or not proper installation has been carried forth. All engines, engine parts and electrical components are for OFF ROAD USE ONLY/ RACING VEHICLES ONLY. They are not for or to be used on public roads in the USA. Acquisition of a Hybrid Racing LLC product will act as an acknowledgement of the legal disclaimer stated herein. Hybrid Racing LLC reserves the right to change this disclaimer at any time without any prior consent or notification. Should you need to us our details are as follows: Hybrid Racing LLC, 12231 Industriplex Suite B, Baton Rouge, LA 70809 www.hybrid-racing.com

8